• 한국정보처리학회논문지
• /
• 제4권9호
• /
• pp.2403-2411
• /
• 1997

Direct3D는 새로운 3차원 그래픽 가속기로써, 이를 이용하여 보다 쉽게 윈도우용 그래픽 프로그램을 제작할 수가 있다. 여기서는 Direct3D를 이용하여 제작한 프랙탈 지형 데이터 모델 뷰어를 제시한다. 지형 모델 뷰어 제작에 따른 클래스의 정의, 입력을 위한 대화상자의 설계, 초기화 과정, 프로그램의 실행과정을 설명하고 지형 모델 뷰어의 실행으로 얻어진 결과중, 철사형, 솔리드형, 포인트형의 출력을 보인다. 지형 형상화의 결과를 보이기 위하여, 여기서는 프랙탈 격자형 중간점 이동 알고리즘에 의하여 만들어진 데이터를 사용하였다.

• 한국태양에너지학회 논문집
• /
• 제32권6호
• /
• pp.85-92
• /
• 2012

A nanofluid is a fluid containing suspended solid particles, with sizes on the order of nanometers. Normally, nanofluids have higher thermal conductivitiest han their base fluids. Therefore, we measured the thermal conductivity and viscosity of oxidized carbon nanofluids based the mixture of distilled water and ethanol (ethanol concentration is 0.2) oxidized carbon nanofluids were made by ultrasonic dispersing oxidized multi-walled carbon nanotubes in the mixture of distilled water and ethanol at the rates of 0.001~ 0.1 vol%. The thermal conductivity and viscosity of oxidized carbon nanofluids were measured by using transient hot-wire method and rotational digital viscometer, respectively. And all of experiments were carried out at the same temperature conditions($10^{\circ}C$, $25^{\circ}C$ and $70^{\circ}C$). As a result, when volume fraction of nanofluids is 0.1 vol%, thermal conductivity was improved 13.6% ($10^{\circ}C$), 15.1% ($25^{\circ}C$), and 17.0% ($70^{\circ}C$), and its viscosity was increased by 36.0% ($10^{\circ}C$), 32.9% ($25^{\circ}C$) and 19.5% ($70^{\circ}C$) than the base fluids.

• 한국태양에너지학회 논문집
• /
• 제32권6호
• /
• pp.93-99
• /
• 2012

A nanofluid is a fluid containing suspended solid particles, with sizes on the order of nanometers. Especially graphene nanoparticle that has the high thermal conductivity properties among the various nanoparticles added to the nanofluid is receiving attention. Graphene is a flat monolayer of $sp^2$-bonded carbon atoms tightly packed into a honeycomb lattice. And are known to have very high thermal conductivity. Therefore, we compared thermal conductivity with viscosity of graphene M-5 nanofluids and graphene M-15 nanofluids. Graphene M-5 and graphene M-15 have different average particle diameters and the other properties are the same. Two kinds of graphene nanofluids was examined by measuring thermal conductivity via transient hot-wire method. And the viscosity was measured by using a rotational digital viscometer. As a result, graphene M-5 nanofluids exhibited better thermal conductivity and viscosity than graphene M-15 nanofluids.

• Journal of Welding and Joining
• /
• 제13권1호
• /
• pp.127-137
• /
• 1995

The possibility of new GMAW process using economic shielding gases including CO$_{2}$ gas was investigated on the effect of shielding gas on weldabilty. In the optimum welding condition using 600A power source, FCAW process showed low depositions rate, 114 g/min at 300A, but new GMAW using other mixed shielding gases exhibited high deposition rate, 208-224 g/min at 450A. TIME gas, Ar+CO$_{2}$ gas and Ar+CO$_{2}$+O$_{2}$ gas as a shielding gas were able to be used to the very high welding current(450A), moreover TIME gas and Ar+CO$_{2}$ gas showed the highest arc stability among shielding gases studied in this experiments. The weld penetration was performed by axial spray transfer mode of weld droplet. On the basis of workability, weldability and economic point of view, Ar mixture (80%Ar+20%CO$_{2}$) gas was recommended as a shielding gas for the development and application of new GMAW process. This shielding gas showed the low spatter, good weld quality, stable arc and low cost at the region of high welding current.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.357-360
• /
• 2002

Nowadays, the improvement and development of Multi-media, information and communication technology are rapidly processed. And many products, for example, digital camera, digital camcorder, and PDA, are used for them. They need large data storage capacity and small size, light storage system. Due to that, many studies and researches in data storage system have been carried out. Especially, micro drive system was presented by IBM.(1) However, its system is expensive and uneasy to be portable. In ODD technologies, 1 inch drive system is not yet or in processing status.(2) If to be possible and to be come up, it is cheap than HDD system and easy to transfer information. In this paper, a miniaturized actuator(about linch) is designed and tested for ODD system. Specially, it is adapted for NFR(Near-field Recoding) system using SIL(Solid Immersion Lens). It is the dual-servo actuator which consists of a coarse actuator and fine actuator. Its actuating force generation method is VCM(Voice Ceil Motor). The fine actuator has 4-wire suspensions and bobbin wrapped by coil and includes focusing motion as well as tracking motion. The coarse actuator has an actuating coil and V-grooved guide mechanism. Also, the characteristics of the designed actuator is estimated by sine-swept mode and LDV(Laser Doppler Vibro-meter).

• Journal of Welding and Joining
• /
• 제23권1호
• /
• pp.69-76
• /
• 2005

Recently, application of arc welding to galvanized carbon steel sheet is on the increasing Ould in the fields of automobile and construction industries. In arc welding process, zinc is evaporated in weld pool, even under the appropriate welding condition and produce blowhole and/or pit. Zinc gas cause instability of arc and increase spatter and fume. This research is purposed to minimize the heat-input and the formation of porosities in the welded joint of the galvanized carbon steel sheet using variable polarity AC wave pulse MIG welding system. An appropriate welding condition which showed low spatter and good bead appearance was acquired by applying the AC pulse MIG welding machine to DC duplicated MIG welding with the solid wire. When oxygen gas was added to shield gas of MIG welding for galvanized steel sheet, arc length was increased and arc stability was improved. In the AC duplicated welding, the loss of galvanized layer was decreased as the amount of heat-input was decreased when the EN ratio was increased under the condition that average welding current was evenly set.

• Journal of Welding and Joining
• /
• 제13권4호
• /
• pp.46-54
• /
• 1995

The cold cracking susceptibility of a variety of weld metals deposited by GMAW with several kinds of commercial solid wires for high strength-toughness steel was investigated. G-BOP test and LB-TRC test were carried out to study the effects of preheat, chemical composition and hydrogen level on the weld metal cold cracking. The results obtained are as follows. 1) 10% CPT obtained by G-BOP test was the most valuable criteria for evaluating the cold cracking susceptibility of weld metals compared with percentage of cracking at room temperature and crack free temperature, and it had good correlation with the results of LB-TRC test. 2) Cold cracking susceptibility of weld metals was high in the row of MG100A, MG100C, MG100D and MG100B. Welds deposited with MG130 and MG80 showed similar icidents of cracking with MG100C and MG100B respectively, even though their strength levels were different. 3) Diffusible hydrogen level in weld metals which has good relation with hydrogen content in wire itself was the most critical factor for controlling the cold cracking susceptibility of weld metal.

• Journal of Welding and Joining
• /
• 제27권2호
• /
• pp.27-31
• /
• 2009

Ferritic stainless steels have a good heat resistance and economic advantage. They are used for applications such as automotive exhaust systems where resistance to general corrosion is superior to carbon steels. However, there are not enough research for ferritic stainless steels on weldability mainly used as automotive exhaust manifolds. In this study, mechanical and microstructure properties of as-welded STS 429L and STS 444 ferrite stainless steels were confirmed by tensile, bending, hardness test, optical microscopy and scanning electron microscopy. Tensile strength of the STS 444 is higher than the STS 429L when it is a raw material. In contrast to this fact, STS 429L indicated higher tensile strength after butt welded. In addition, the hardness have a increasing tendency as getting down on the bead.

• 대한기계학회논문집A
• /
• 제20권11호
• /
• pp.3525-3537
• /
• 1996

This paper presents a CAD program develpoed on a microcomputer in order to support graphic and computational assessment of ergonomic problems associated with the design of a man-in-cab system. The program is coded to help workspace designers with ergonomic evaluations needed in the design stage. This paper proposed a biomechanical -ergonomic evaluations needed using man and workplace models. The human model is developed to have dimensions obtained from the Korean anthropometric data reported in 1992. Its graphical representation is based on a wire-frame model but, whenever necessary, body segments can be represented by a solid model with hidden line/faces removed and shaded. Workplace models are presented for cabs of the excavator, one of the most popular construction vehicles. A workplace model consists of an operator seat, a steering wheel. two control levers, two pedals, and a control panel. The workplace elements can be modified in their sizes, positions, and orientations by changing the reference point and design parameters. An algorithm for the view test is suggested and loaded to provide a visual evaluaiton of the overall layout of a workplace model.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2009년도 하계학술발표대회 논문집
• /
• pp.1379-1384
• /
• 2009

High power light emitting diode(LEDs), a strong candidate for the next generation general illumination applications are of interest. With major advantages of power saving, increased life expectancy and faster response time over traditional incandescent bulb, the LEDs are rapidly taking over many applications such as LCD backlighting, traffic light, automotive lighting, signage, etc. The increased electrical currents used to drive the LEDs have focused more attention on the thermal management because the efficiency and reliability of the solid-state lighting devices strongly depend on successful thermal management. There exist some problems that are caused by heat generation in the LED package, such as wire breakage, yellowing of epoxy resin, lifted chip caused by reflow of thermal paste chip attach and interfacial separation between LED package and silicon resin. The goal of this study is to analyze high power LED thermal properties of using pulsating heat pipe.