• Journal of Korea Foundry Society
• /
• v.22 no.3
• /
• pp.109-113
• /
• 2002

A good fluidity of high strength Al-alloys is required to cast thin wall castings needed to reduce the weight of cast parts. The fluidity, measured as the length to which the metal flows in a standard channel, is affected by many factors, such as the pouring temperature, solidification type of the alloy, the channel thickness, melt head, mold materials and temperature, coating etc. Therefore the experimentally measured fluidity scatters very much and makes it difficult to estimate the fluidity of a melt with a few measurements. The effect of Ti content and grain refinement on the fluidity of high strength aluminum alloy was investigated with a test casting with 8 thin flow channels to reduce the scattering of the fluidity results. The fluidity of Al-4.8%Cu-0.6%Mn Al-6.2%Zn-1.6%Mg-1.0%Cu and well-known commercial aluminum alloy, A356 was tested. Initial content of Ti was varied from 0 to 0.2wt% and Al-5Ti-B master alloy was added for grain refinement. The flow length varied linearly with superheat. By adding Ti and Al-5Ti-B, the fluidity increased. The grain size decreased by adding grain refiner at the same time. The fluidity depended on the degree of grain refinement. The fluidity of the alloy solidifying in mushy type is improved by grain refinement, because grain refinement increases the solid fraction at the time of flow stoppage.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.1
• /
• pp.67-74
• /
• 2002

A phosphor for Plasma Display Panel, BaMgAl$_{10}$ O$_{17}$ :Eu$^{2+}$, showing a blue emission band at about 450nm was prepared by a solid-state reaction using BaCO$_3$, $Al_2$O$_3$, MgO, Eu$_2$O$_3$ as starting materials wish flux AlF$_3$. The study of the behaviour of Eu in BAM phosphor was carried out by the photoluminescence spectra and the Rietveld method with X-ray and neutron powder diffraction data to refine the structural parameters such as lattice constants, the valence state of Eu, the preferential site of Mg atom and the site fraction of each atom. The phenomenon of the concentration quenching was abound 2.25~2.3wt% of Eu due to a decrease in the critical distance for energy transfer of inter-atomic Eu. Through the combined Rietveld refinement, R-factor, R$_{wp}$, was 8.11%, and the occupancy of Eu and Mg was 0.0882 and 0.526 at critical concentration. The critical distance of Eu$^{2+}$ in BAM was 18.8$\AA$ at 2.25% Eu of the concentration quenching. Furthermore, c/a ratio was decreased to 3.0wt% and no more change was observed over that concentration. The maximum entropy electron density was found that the modeling of $\beta$-alumina structure in BaMgAl$_{10}$ O$_{17}$ :Eu$^{2+}$correct coincided showing Ba, Eu, O atoms of z= 1/4 mirror plane.e.ane.e.

• Nuclear Engineering and Technology
• /
• v.48 no.2
• /
• pp.525-532
• /
• 2016

High-energy linear accelerators are increasingly used in the medical field. However, the unwanted photo-neutrons can also be contributed to the dose delivered to the patients during their treatments. In this study, neutron fluxes were measured in a solid water phantom placed at the isocenter 1-m distance from the head of an18-MV linac using the foil activation method. The produced activities were measured with a calibrated well-type Ge detector. From the measured fluxes, the total neutron fluence was found to be $(1.17{\pm}0.06){\times}10^7n/cm^2$ per Gy at the phantom surface in a $20{\times}20cm^2$ X-ray field size. The maximum photo-neutron dose was measured to be $0.67{\pm}0.04$ mSv/Gy at $d_{max}=5cm$ depth in the phantom at isocenter. The present results are compared with those obtained for different field sizes of $10{\times}10cm^2$, $15{\times}15cm^2$, and $20{\times}20cm^2$ from 10-, 15-, and 18-MV linacs. Additionally, ambient neutron dose equivalents were determined at different locations in the room and they were found to be negligibly low. The results indicate that the photo-neutron dose at the patient position is not a negligible fraction of the therapeutic photon dose. Thus, there is a need for reduction of the contaminated neutron dose by taking some additional measures, for instance, neutron absorbing-protective materials might be used as aprons during the treatment.

• Korean Journal of Ecology and Environment
• /
• v.48 no.3
• /
• pp.168-175
• /
• 2015

This study was conducted in autumn to determine phosphorus (P) fraction in sediments of Daechung Lake, to elucidate controlling factors for sedimentary P, and to compare with the other areas. For this study, sediment samples were collected at 6 sites only once on November 2014 using ponar grab and analyzed for solid-phase P (Loosely adsorbed, Fe-bound, Al-bound, detrital apatite, and refractory organic P) by sequential extraction. Total phosphorus (TP) was relatively high in front of Daechung Dam and Hoinam where fish farm was run until 1997. The dominant sedimentary P form was Al-bound P, followed by Fe-bound P, which could be released from sediment to water column during suboxic state. Based on principal component analysis, Al-bound P, Fe-bound, and TP were controlled by grain size of sediments. Loosely adsorbed, detrital apatite, and refractory organic P were relatively highly accumulated at the mouth of major tributaries where suspended sediments were delivered. Sedimentary P concentrations in Daechung Lake sediments were not higher than in other lake sediments. Therefore, based on these results, major controlling factors were grain size and input of suspended sediments from tributaries.

• Nuclear Engineering and Technology
• /
• v.51 no.5
• /
• pp.1406-1416
• /
• 2019

In this research, a multi-slit prompt-gamma camera was developed to locate the distal dose falloff of the proton beam spots in spot scanning proton therapy. To see the performance of the developed camera, therapeutic proton beams were delivered to a solid plate phantom and then the prompt gammas from the phantom were measured using the camera. Our results show that the camera locates the 90% distal dose falloff (= d90%), within about 2-3 mm of error for the spots which are composed $3.8{\times}10^8$ protons or more. The measured location of d90% is not very sensitive to the irradiation depth of the proton beam (i.e., the depth of proton beam from the phantom surface toward which the camera is located). Considering the number of protons per spot for the most distal spots in typical treatment cases (i.e., 2 Gy dose divided in 2 fields), the camera can locate d90% only for a fraction of the spots depending on the treatment cases. However, the information of those spots is still valuable in that, in the multi-slit prompt-gamma camera, the distal dose falloff of the spots is located solely based on prompt gamma measurement, i.e., not referring to Monte Carlo simulation.

• Journal of the Korea Institute of Building Construction
• /
• v.19 no.3
• /
• pp.219-228
• /
• 2019

The aim of the research is to provide a fundamental data of low viscosity typed superplasticizer (SP) on cement-based materials incorporating various supplementary cementitious materials (SCMs). As a relatively new product, low-viscosity typed SP has introduced for high performance concrete with high viscosity due to its high solid volume fraction with various SCMs. However, there are not enough research or reports on the performance of the low viscosity typed SP with cement-based materials incorporting SCMs. hence, in this research, for cement paste and mortar, fluidity and rheological properties were evaluated when the mixtures contained various SCMs such as fly ash, blast furnace slag, and silica fume. From the experiment conducted, it was checked that the low viscosity typed superplasticizer decreased the plastic viscosity of the mixture as well as the yield stress. From the results of this research, it is expected to contribute on introduction of new type SP for high performance concrete or high-viscous cementitious materials.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2023.05a
• /
• pp.313-313
• /
• 2023

이 연구에서는 침수식생 조건에서 식생 형태 별 frontal area, solid volume fraction이 유속 분포에 미치는 영향을 분석하고, 흐름측정결과로부터 식생 형태에 따른 난류흐름특성을 분석하기 위하여 수행 되었다. 식생흐름 구현을 위하여 5 cm의 간격으로 총 257개의 모형식생을 전체 영역에 배치했다. 유속측정위치는 수위측정결과에 따라 흐름이 안정화되는 구간에서 연직방향으로 17개 지점에서 측정한 후 앙상블 평균하여 분석했다. Branch의 유무에 따라 Type I과 II로 구분하여 각 식생에 대해 유속의 연직분포를 측정한 결과, Branch가 없는 Type I에서는 유속이 지속적으로 감소하는 반면, Type 2에서는 Frontal area가 급격히 증가하는 Branch 구간에서 유속이 급격히 감소한 후 Trunk 구간에서 유속이 다시 증가하는 변화를 보였다. Velocity Spectrum 분석 결과, 모든 지점에 대해 평균한 결과 고주파수 영역에서 -5/3 law를 따르는 것으로 나타나 전체 영역에서 isotropic & homogeneous 난류흐름이 발생함을 확인했다. 난류흐름특성 계산결과, Turbulent kinetic energy(k)를 mean kinetic energy(K)로 무차원화하여 연직분포를 비교했을 때 -k/K는 모두 식생에 근접하며 증가했다. Shear production(P_s)의 계산결과로부터 전단흐름에 의한 난류운동에너지 생성영향분석결과, Type I과 II가 식생경계의 mixing interface 부근에서 급격히 증가하는 분포를 보였으며, 이는 시간평균유속분포에서 분석한 결과와 일치한다. Wake production(P_w)의 연직분포계산결과, P_s와 유사하게 식생경계 부근에서 상승하는 결과가 나타났으며, 이는 식생경계에서 발생하는 Large scale eddy로 인해 발생함을 알 수 있다. 마지막으로 x-방향 난류확산계수로부터 scale factor(α_x)의 연직분포를 계산한 결과, 식생경계부근의 mixing interface에서 증가한 후 식생영역 내에서 감소하는 분포를 나타냈다. z-방향 난류확산 계수의 scale factor(α_z)는 α_x에 비해 작게 계산되었다. 이러한 결과는 오염물질의 연직확산이 식생경계에서 증가한 후 식생 내부에서 감소하여 오염물질, 부유사 등의 축적이 이뤄질 것으로 예상된다. 이는 가지로 인해 식생저항이 증가할 경우 용존성 물질의 혼합이 감소하여 식생의 저장대 효과가 증가함을 의미한다.

• Progress in Superconductivity and Cryogenics
• /
• v.25 no.2
• /
• pp.5-9
• /
• 2023

The effect of La_0.7Sr_0.3MnO₃ (LSMO) addition on the superconducting property of Bi_1.6Pb_0.4Sr₂Ca₂Cu₃O_10+δ ((Bi, Pb)-2223) polycrystalline samples was studied. LSMO (0.3 wt.% to 2.0 wt.%) added (Bi, Pb)-2223 samples were prepared by using a solid-state reaction method. The XRD analyses show that as the LSMO addition increases, the volume fraction of the Bi-2223 phase is gradually decreased. The critical temperature (T_c) exhibits a gradual decrease with a single transition as the LSMO amount increases up to 1.0 wt.%, but a further addition of LSMO induces an abrupt decrease of T_c with a dual transition. The analyses on the local structure of the CuO₂ plane from the X-ray absorption fine structure (EXAFS) measurements showed that for the samples with low concentration of LSMO up to 1.0 wt.%, the Cu-O bond length and the CuO₂ plane ordering do not degrade from the values of pure (Bi, Pb)-2223, while they get worsen with a further increase of LSMO addition. These results open up the possibility of LSMO as artificial pinning centers of the (Bi, Pb)-2223 system for power application.

• Advances in nano research
• /
• v.16 no.4
• /
• pp.341-352
• /
• 2024

This study investigates the heat and mass transfer characteristics of a MoS₂ nanoparticle suspension in ethylene glycol over a porous stretching sheet. MoS₂ nanoparticles are known for their exceptional thermal and chemical stability which makes it convenient for enhancing the energy and mass transport properties of base fluids. Ethylene glycol, a common coolant in various industrial applications is utilized as the suspending medium due to its superior heat transfer properties. The effects of variable thermal conductivity, variable mass diffusivity, thermal radiation and thermophoresis which are crucial parameters in affecting the transport phenomena of nanofluids are taken into consideration. The governing partial differential equations representing the conservation of momentum, energy, and concentration are reduced to a set of nonlinear ordinary differential equations using appropriate similarity transformations. R software and MATLAB-bvp5c are used to compute the solutions. The impact of key parameters, including the nanoparticle volume fraction, magnetic field, Prandtl number, and thermophoresis parameter on the flow, heat and mass transfer rates is systematically examined. The study reveals that the presence of MoS₂ nanoparticles curbs the friction between the fluid and the solid boundary. Moreover, the variable thermal conductivity controls the rate of heat transfer and variable mass diffusivity regulates the rate of mass transfer. The numerical and statistical results computed are mutually justified via tables. The results obtained from this investigation provide valuable insights into the design and optimization of systems involving nanofluid-based heat and mass transfer processes, such as solar collectors, chemical reactors, and heat exchangers. Furthermore, the findings contribute to a deeper understanding of stretching sheet systems, such as in manufacturing processes involving continuous casting or polymer film production. The incorporation of MoS₂-C₂H₆O₂ nanofluids can potentially optimize temperature distribution and fluid dynamics.

• Economic and Environmental Geology
• /
• v.35 no.6
• /
• pp.491-508
• /
• 2002

While about 80% of Jeju soils are classified as Andisols, the soils derived from volcanic ash in Dangsanbong are not Andisols. There is a significant difference of precipitation in localities of Jeju island. The study area is characterized by the lowest amount of annual rainfall in Jeju Island, and by the layered silicates as dominant solid phase in clay fraction. The purpose of this study was to characterize the mineralogy of the non-Andie soils in detail, especially hydroxy-interlayered silicates. Two major soil horizons are recognized in the soil profile developed in the Dangsanbong area, which can be designated as A and C. The soil pH($H_{2}0$), ranges from 6.6 to 7.3 increasing with depth, is higher than that of typical Andisols(pH<6.0). While the pH(NaF), ranges from 9.49 to 9.81, indicates that significant amount of amorphous phases might be present as exchanging complexes. It is estimated to about 1.542.88 wt% by using chemical selective dissolution. The organic content of surface horizon is about 2 wt%. This soil are composed of quartz, feldspar and olivine as major constituents with minor of silicate clays. Quartz is frequently observed in A and distinctly decreases in its amount with depth, while olivine is dominant phase in C and rarely observed in A. In the <0.2$\mu\textrm{m}$ size fraction, smectite and kaolinite/smectite interstratification are dominant with minor of illite. The amounts of smectite decrease with depth, while the amounts of kaolinite/smecite interstratification increase with depth, which indicates the trend of mineral transformation with increasing the degree of weathering. The proportion of kaolinite in kaolinite/smectite interstratification is about 85%, and is not changed significantly through the profile. In the 2-0.2$\mu\textrm{m}$size fraction, vermiculite, smectite, illite and kaolinite are major components with minor of chlorite. Most of chlorite are interstratified with smectite. Chlorite which is not interstratified with smectite occurs only in surface horizon. The proportion of the chlorite in the chlorite/smectite interstratification is 59-70(%) and increases with depth. Hydroxy-interlayered vermiculite(HIV) with hydroxy-Fe/AI in their interlayers occurs in both A and C horizon. The amounts of hydroxy-Fe/AI decrease with depth. Hydroxy-interlayered smectite(HIS) of which interlayers might be composed of hydroxy-Mg/Al occurs only in C horizon. As the results of mineralogical investigation for the soil profile in the study area, clay minerals might be changed and evolved through the following weathering sequences: 1) Smectite Kaolinite, HIS, Vermiculite, 2) Vermiculite HIV Chlorite.