• ETRI Journal
• /
• v.39 no.6
• /
• pp.859-865
• /
• 2017

This paper presents a method for determining the optimum active-area width (OAW) of solar cells in a module architecture. The current density-voltage curve of a reference cell with a narrow active-area width is used to reproduce the current density profile in the test cell whose active area width is to be optimized. We obtained self-consistent current density and electric potential profiles from iterative calculations of both properties, considering the distributed resistance of the contact layers. Further, we determined the OAW that yields the maximum efficiency by calculating efficiency as a function of the active-area width. The proposed method can be applied to the design of the active area of a dye-sensitized solar cell in Z-type series connection modules for indoor and building-integrated photovoltaic systems. Our calculations predicted that OAW increases as the sheet resistances of the contact layers and the intensity of light decrease.

• Bulletin of the Korean Chemical Society
• /
• v.24 no.10
• /
• pp.1501-1504
• /
• 2003

Single-wall carbon nanotubes (SWCN) were integrated in $TiO_2$ film and the beneficial influence on the dyesensitized solar cells in terms of improved photocurrent was studied in the light of static J-V characteristics obtained both under illumination and in the dark, photocurrent transients, IPCE spectra and impedance spectra. Compared with a solar cell without SWCN, it is established that the photocurrent density of the modified cell increases at all applied potentials. The enhanced photocurrent density is correlated with the augmented concentration of electrons in the conduction band of $TiO_2$ and with increased electrical conductivity. Explanations are additionally corroborated with the help of SEM, Raman spectra and dye-desorption measurements.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.3
• /
• pp.66-71
• /
• 1992

We fabricated highly stable a-Si:H solar cell using low band gap intrinsic layer fabricated by RP-CVD. We obtained a-Si:H with optical band gap of less than 1.65 eV with deposition rate of 0.18 $\AA$/sec, and used this material as bottom i-layer of a-Si:H double stacked solar cells. We have succeeded in the fabrication of very stable a-Si:H double stacked solar cell of which the conversion efficiency is about 9% and the degradation is less than 4% after light illumination for 100h under 350mW/cm$^{2}$.

• Journal of the Korean Solar Energy Society
• /
• v.29 no.1
• /
• pp.64-69
• /
• 2009

This paper aims at enhancing the electric production efficiency of photovoltaic(PV) system. The electrical power of PV system is proportional to light intensity on a PV module surface. In this paper, we apply two types of systems to enhance power generation efficiency. First, of all, concentring sunlight using specular surface and one-axis tracking system which traces the sun with vertical direction are applied in this project. From this, we analyze the fixed type method and power generation efficiency.

• Electrical & Electronic Materials
• /
• v.1 no.1
• /
• pp.26-34
• /
• 1988

Sintered CdS/CdTe solar cells have been farbricated by coating a (Cd+Te) slurry on sintered CdS films followed by the sintering at 625.deg.C for one hour with various heating rates. When cadmium and tellurinm powders are used instead of CdTe powder to form CdS/CdTe junction, CdTe is formed in the temperature range of 290.deg.C-400.deg.C. The microstructure of the CdTe films depends strongly on the heating rate of the sintering due to the low melting temperature and the high vapor pressure of the elemental Cd and Te. An optimum heating rate obtain CdTe films with uniform and dense microstructure which, in turn, improves the efficiency of the sintered CdS/CdTe solar cells. All-polycrystalline CdS/CdTe solar cells with an efficiency of 9.57% under 50mW/cm$^{2}$ tungsten light have been farbricated by using a heating rate of 14.deg.C/min.

• International Journal of Internet, Broadcasting and Communication
• /
• v.13 no.2
• /
• pp.93-102
• /
• 2021

In this research, we present a natural lighting system with transmission distance of 30m and lighting efficiency of 35% (30m standard) for operating hours of 7h/day (based on clear sky). The system is composed of parabolic reflective mirror and modified light pipe that can secure more than 88% of light concentration efficiency. The light loss rate of newly designed light pipe transmission system is demonstrated to 0.8 %/m in the straight-line part and 2%/m in the curved part. Modified light pipe daylighting system shows better performance over fiber optic daylighting system in terms of transmission distance (1.5 times longer) and illuminance (3.05 times higher).

• Bulletin of the Korean Chemical Society
• /
• v.34 no.6
• /
• pp.1853-1856
• /
• 2013

$TiO_2$ hollow nanoparticles (HNPs) and their light scattering effect which influences on the photoelectric conversion efficiency of a dye-sensitized solar cell (DSSC) were investigated. When only HNPs were employed in DSSC as the anode layer material, the conversion efficiency (e.g., 0.96%) was the lowest, possibly due to scattering loss of incident light. However, DSSC fabricated by using HNPs as a scattering overlayer on the $TiO_2$ nanoparticles (P-25), showed higher conversion efficiency (4.02%) than that without using HNPs (3.36%).

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.495-498
• /
• 2008

Photocatalytic water splitting into $H_2$ and $O_2$ using semiconductors has received much attention, especially for its potential application to direct production of $H_2$ for clean energy from water utilizing solar light energy. Since the report of Fujishima and Honda on the water splitting by photoelectrochemical cells, numerous different semiconducting materials have been used as photocatalysts for hydrogen generation from water. Among them, platinized titania significantly accelerates hydrogen production from water. For geometrical improvement of $TiO_2$ particle, porous $TiO_2$ structure was proposed and studied such as nanofiber, nanorod and nototubes. This research focuses on finding out the optimum temperature and electrolyte to produce $H_2$ by solar water splitting.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.126.1-126.1
• /
• 2011

박막형 태양전지의 효율 향상을 위하여 광확산 패턴이 형성된 기판을 제작하고 이를 이용하여 비정질 실리콘 박막 태양전지를 제작하였다. 나노 임프린트 방법을 사용하여 제작된 광확산 패턴은 불규칙한 마이크로-나노 크기의 미세구조를 가지고 있어 빛의 확산투과 비율을 향상시켜주는 역할을 하였다. 제작된 광확산 기판위에 TCO물질을 증착하고, PECVD법을 사용하여 비정질 실리콘 p-i-n 접합 구조를 형성하였다. 제작된 태양전지 소자를 1.5 AM의 조건에서 I-V 특성을 분석하였으며, 비교군으로 사용된 일본 Asahi 사의 U-type glass에 비해 높은 Jsc 값을 나타내었다. 또한 외부양자효율을 측정함으로써 광확산 패턴에 의한 양자효율 변화를 확인 할 수 있었다.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.7.2-7.2
• /
• 2011

Photoelectrochemical solar cells such as dye-sensitized cells (DSSCs), which exhibit high performance and are cost-effective, provide an alternative to conventional p-n junction photovoltaic devices. However, the efficiency of such cells plateaus at 11~12%, in contrast to their theoretical value of 33%. The majority of research has focused on improving energy conversion efficiency of DSSC by controlling nanostructure and exploiting new materials in photoelectrode consisting of semiconducting oxide nanoparticles and a transparent conducting oxide electrode (TCO). In this presentation, we introduce monodisperesed TiO2 nanoparticles prepared by forced hydrolysis method and their superiority as photoelectrode materials was characterized with aids of optical and electrochemical analysis. Inverse opal-based scattering layers containing highly crystalline anatase nanoparticles are also introduced and their feasibility for use as bi-functional light scattering layer is discussed in terms of optical reflectance and charge generation properties as a function of optical wavelength.