• Journal of the Korean Solar Energy Society
• /
• v.33 no.1
• /
• pp.89-95
• /
• 2013

A DBLP(Double blind light pipe) daylight system can be installed at a building exterior wall or roof to replace artificial light during the day time. This system was consisted of a double blind light collector, a mirror duct type light transformer and a prism light pipe distributor. The double blinds were used to track the sun's altitude and azimuth movements to collect the sunlight throughout the day. The sunlight collected by the light collector was reflected on the first mirror and the second mirror and sent to the light pipe through the light transformer. The transformer was designed to deliver the sunlight into the light pipe efficiently. The light distributor plays a role in diffusing the sunlight coming in through the light collector to be used for indoor lighting. In this paper, a DBLP system has been designed, installed and tested at a KIER daylighting twin test cell. The DBLP daylighting system was applied to the experimental test cell which has an indoor area of 2.0 m wide ${\times}$ 2.4 m height ${\times}$ 3.8 m length. The experiment was conducted from January 30 to February 27, 2012, under clear skies and partially cloudy skies. Data was collected from 10:00 am to 16:00 pm every 2 minute and the average was calculated for every 30 minute of the data collection to obtain the system efficiency. The results indicated that the DBLP system efficiency was evaluated as 11.67%. The DBLP system indoor illumination energy reduction was predicted as 0.822 kWh/day. This could replace 4 sets of a 32W fluorescent lamp operating 6.4 hours per a day.

• Journal of The Korean Astronomical Society
• /
• v.50 no.4
• /
• pp.105-109
• /
• 2017

The well-known solar cycle controls almost the entire appearance of the solar photosphere. We therefore presume that the continuous emission of visible light from the solar surface follows the solar cyclic variation. In this study, we examine the solar cyclic variation of photospheric brightness in the visible range using solar images taken by the Solar and Heliospheric Observatory (SOHO)/Michelson Doppler Imager (MDI). The photospheric brightness in the visible range is quantified via the relative intensity acquired from in the raw solar images. In contrast to total solar irradiance, the relative intensity is out of phase with the solar cycle. During the solar minimum of solar cycles 23-24, the relative intensity shows enhanced heliolatitudinal asymmetry due to a positive asymmetry of the sunspot number. This result can be explained by the strength of the solar magnetic field that controls the strength of convection, implying that the emission in the visible range is controlled by the strength of convection. This agrees with the photospheric brightness increasing during a period of long spotless days.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.61 no.2
• /
• pp.97-102
• /
• 2012

CPV system in the desert areas or areas near the equator, as is suitable for high-temperature region. As compared to silicon solar cells, CPV system have a high proportion of a BOS (balance of system). Solar cells because of its low proportion when designing a module technology is applied in a variety of ways. Applied to the CPV system is classified into two kinds of optical technology. One of those using fresnel lens uses refraction of light energy. The other is a mirror reflection of the structure using sprays. Both of these two ways to condense the sun to collect solar cell is a form of light. And goals by using a small solar cell materials is to produce more energy. In this paper, suitable for a domestic environment, with the aim CPV Manufacturing Technology, built on a variety of modular process technology to the development of a prototype performance analysis was carried out. In particular, silicone coated on the glass by the method of implementation of the Fresnel lens SOG(Silicon on glass) by applying the lens to absorb the solar spectrum was broad. In addition to, for the analyze to characteristics of the CPV module, developed CPV module performance and generating characteristics studied. These related technology through research and development of high-performance multi-junction solar cells, modules, development of concentrating solar power systems to facilitate the growth of the market is considered to be.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.236.1-236.1
• /
• 2015

The surface morphology of front transparent conductive oxide (TCO) films is very important to achieve high current density in amorphous silicon (a-Si) thin film solar cells since it can scatter the light in a better way. In this study, we present the low cost hydrothermal deposited uniform zinc oxide (ZnO) nano-flower structure with various aspect ratios for a-Si thin film solar cells. The ZnO nano-flower structures with various aspect ratios were grown on the RF magnetron sputtered AZO films. The diameters and length of the ZnO nano-flowers was controlled by varying the annealing time. The length of ZnO nano-flowers were varied from 400 nm to $2{\mu}m$ while diameter was kept higher than 200 nm to obtain different aspect ratios. The ZnO nano-flowers with higher surface area as compared to conventional ZnO nano structure are preferred for the better light scattering. The conductivity and crystallinity of ZnO nano-flowers can be enhanced by annealing in hydrogen atmosphere at 350 oC. The vertical aligned ZnO nano-flowers showed higher haze ratio as compared to the commercially available FTO films. We also observed that the scattering in the longer wavelength region was favored for the high aspect ratio of ZnO nano-flowers. Therefore, we proposed low cost and vertically aligned ZnO nano-flowers for the high performance of thin film solar cells.

• Journal of the Korean Solar Energy Society
• /
• v.27 no.3
• /
• pp.175-179
• /
• 2007

This experimental demonstration has successfully shown that it is possible to use direct sunlight for the illumination of deeper building zones using the material for light path system(light duct). Three kinds of reflectors which were 95% Silver vaporizing fixed, 85% Anodized and 85% Hot melted applied to evaluate and compare their performances each others. Also, these three kind of reflectors were compared in view point of economics. The most high performance was obtained in 95% Silver vaporizing fixed reflector hater than another reflectors of 85% Anodized reflector and 85% Hot melted reflector even though more high production cost in 95% Silver vaporizing fixed reflector. The rest two reflectors of 85% Anodized and 85% Hot melted $10{sim}15%$ less performance than 95% Silver vaporizing fixed reflector but their production cost were low than the production cost of 95% Silver vaporizing fixed reflector which identified very weak and light yellow color in the light.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1503-1504
• /
• 2011

염료 감응형 태양전지(Dye-sensitized Solar Cells, DSC)에서 고효율화를 위해 light scattering layer가 반도체 산화물 $TiO_2$와 함께 많이 사용되고 있다. 이것은 light scattering layer에 의해 빛의 이용률을 증가시킴으로써 DSC의 성능을 증대 시킬 수 있기 때문이다. 따라서 본 연구에서는 입자크기가 크고 반사율이 좋은 $Nb_2O_5$를 light scattering layer로 사용하여 $TiO_2$ layer를 통과한 빛을 다시 반사시켜 빛의 이용률을 증대시킴으로써 DSC 성능면에서 light scattering layer를 사용하지 않았을 때보다 전류밀도와 효율을 크게 증가시키고자 하였다. 그 결과 $V_{OC}$는 0.74V, $J_{SC}$는 17.95mA/$cm^2$, FF는 0.63, ${\Box}$는 8.38%로 기존의 DSC 보다 전류밀도가 약 30%, 효율이 약 31% 증가한 좋은 결과를 얻을 수 있었다.

• Journal of the Korean Solar Energy Society
• /
• v.32 no.1
• /
• pp.48-55
• /
• 2012

In recent years, it clearly shows the tendency toward the utilization of daylight in many exhibitory buildings such as museum since the expectation of visitors for whom high illuminance levels are preferable to perceive the details of the works of art. Shading devices and special glazings are often used as the tool to control the amount of light and heat which should be avoided for the presentation of high-light sensitive art works such as paintings. Another way of controling the light is to provide the space for inducing and attenuating light in the exhibitory building. This study aims to investigate the illuminance on the exhibitory space when the space for inducing and attenuating light is applied. Interaction between the daylight and the space was simulated by Lumen Micro program with variation of the size of the exhibitory space, the length of inner wall, surface reflectivity, area of windows to obtain the illumination of the wall surface. This study shows that those variables affect the illumination on the wall surfaces. By comparing the results with suggestive illumination of KS and ICOM, available wall for display on natural lighting are suggested for the seasons and time.

• Journal of the Korean Institute of Rural Architecture
• /
• v.10 no.1
• /
• pp.67-74
• /
• 2008

Recently, construction of bridges in rural areas has been increased to preserve the natural environment. However this brings forth the disputes over rights of light in farmland. In urban areas, the disputes over rights of light have been settled on the authority of the national architectural law and only sunshine hours for winter solstice are considered. Basically, the point at issue is different between each case. The main issues of the dispute in rural area were the reduction of the crop cultivation and the increase of the heating cost in winter. The purpose of this study is to review the mediation process in national environmental dispute resolution commission to resolve these issues, and to set up the analysis method of rights of light and modelling equation of solar position. Furthermore, we aimed at analyzing the damaged hours of daylights in rural housing and the infringement rate of daylight in farmland through the case study. In conclusion, we estimated the sunshine hours during the whole damaged periods according to the elements of bridges, and presented the solution process of dispute over rights of light due to the construction of bridge in rural area.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1421-1423
• /
• 1996

In this study, the effect of solar cell cover glass on the solar cell performance is evaluated. Silicon solar cell (active area:4*6cm, efficiency:12.6% at AMO condition) is used for this study. ITO(Indium tin Oxide) film thickness of the ITO/AR/substrate glass/solar cell structure samples are $40{\AA}$, $60{\AA}$, $160{\AA}$, $240{\AA}$ respectively. The solar cell maximum output power on the stacking structure variations showed 465mW in the AR/ITO/substrate glass/solar cell, and minimum output power showed 403mW in the AR/substrate glass/solar cell. The maximum output power of the solar cell on the ITO thickness variations of the ITO/AR/substrate glass/solar cell showed 460mW at $40{\AA}$ then decrease output power as ITO thickness increase. For environment tests, all samples are exposed UV light in the vacuum chanber. The output power degradation of AR(UVR)/substrate glass/solar cell stacking structure is small compared with ITO/AR(UVR)/substrate glass/solar cell stacking structure.

• Ceramist
• /
• v.22 no.2
• /
• pp.146-169
• /
• 2019

To overcome the theoretical efficiency of single-junction solar cells (> 30 %), tandem solar cells (or multi-junction solar cells) is considered as a strong nominee because of their excellent light utilization. Organic-inorganic halide perovskite has been regarded as a promising candidate material for next-generation tandem solar cell due to not only their excellent optoelectronic properties but also their bandgap-tune-ability and low-temperature process-possibility. As a result, they have been adopted either as a wide-bandgap top cell combined with narrow-bandgap silicon or CuIn_xGa_(1-x)Se₂ bottom cells or for all-perovskite tandem solar cells using narrow- and wide-bandgap perovskites. To successfully transition perovskite materials from for single junction to tandem, substantial efforts need to focus on fabricating the high quality wide- and narrow-bandgap perovskite materials and semi-transparent electrode/recombination layer. In this paper, we present an overview of the current research and our outlook regarding perovskite-based tandem solar technology. Several key challenges discussed are: 1) a wide-bandgap perovskite for top-cell in multi-junction tandem solar cells; 2) a narrow-bandgap perovskite for bottom-cell in all-perovskite tandem solar cells, and 3) suitable semi-transparent conducting layer for efficient electrode or recombination layer in tandem solar cells.