• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.47 no.6
• /
• pp.6-11
• /
• 2010

Amount of power generated from solar photovoltaic can vary according to solar flux of sunlight due to nature of solar cell panel, and an angle that the sun and the surface of cell makes brings difference in amount of power generation. Solar flux is decided by location of surface of the Earth that is classified into longitude and latitude, but on the other hand, an angle that the sung and the surface of cell makes can be changed by changing the angle of a solar power generation device at the fixed location. A method of changing the angle of a solar power generation device as a measure for improving practical power generation efficiency. and studies about a solar tracking device for this are in active. This study conducted a research on a solar tracking system for improvement of solar power generation efficiency. A solar tracking system of this study is composed of a sensor part to confirm a location of the sun with a semiconductor photosensor using the photo conductive effect, and it analyzed output signal of a sensor by using microprocessor and it produced a control signal of driving part for tracking the sun. A solar power generator (25W) was produced to analyze performance of a solar tracking system and usefulness of a solar tracking device that was designed and produced in this study was confirmed through experiments.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.239-240
• /
• 2012

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.10a
• /
• pp.307-308
• /
• 2009

• New & Renewable Energy
• /
• v.5 no.3
• /
• pp.22-25
• /
• 2009

For increasing the output voltage, six SMD(surface mount device) type AlGaAs/GaAs solar cells were connected in series. The electrical properties of the array were measured and compared with one sun (100 mW/$cm^2$) and indoor light (480 lux) conditions. Under one sun condition, output power was 21.57 mW and it was $14.67\;{\mu}W$ under indoor light condition. Under the indoor light condition, the intensity of the light is very low compared to one sun condition. Thus the Voc(open circuit voltage) and Isc (short circuit current) of the sample under indoor light condition decreased very much compared to that of under the one sun condition. This kind of solar cell power supply can be used as a power source for ubiquitous sensor network (USN).

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.938-941
• /
• 2003

In this paper we develop an equipment which prevents vehicles from overheating their inside due to exposure to direct sunlight in summer. Overheating of inside vehicle may give rise to accidents, for instances, dying from suffocation, the deformation of its internal equipment and the explosion from the cracks of its internal parts etc.. The equipment is operated under no starting engine. We adjust the overheating of the inside vehicle by operating the equipment. This equipment checks the temperature of the inside vehicle using temperature sensor. If the temperature increases more than reference temperature(a condition which can be given by the driver), the equipment will operate until the temperature of the inside decreases to the given temperature. Its power is obtained from solar cell. So the equipment keeps away overheating accidents as well as provides the drivers with optimized condition. And also it increases the ability of original car battery through solar cell.

• Journal of Sensor Science and Technology
• /
• v.26 no.3
• /
• pp.173-178
• /
• 2017

In this paper, we newly developed an omnidirectional receiver for visible light communication (VLC). The omnidirectional receiver was composed of a flexible solar cell attached on a cylindrical surface with its axis in vertical direction. The solar cell surface was symmetrical and showed an almost uniform receiving pattern in a horizontal plane. The maximum difference in a receiving pattern was within 7% of its peak value in a horizontal plane. This configuration is very easy to fabricate and useful in constructing wireless sensor networks in which one receiver needs to detect multiple LED signals in different directions.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.8
• /
• pp.1529-1536
• /
• 2011

Recently, worldwide government policy is pursuing saving energy and preservation. add to this, the solar cells are getting the spotlight nonpolluting energy source, using a variety of products for solar cell. in this paper, we'll make solar tracking system for suitable of dynamic boat. we knew that general boats are using fixed solar cell, it's first time to use tracking system of solar cells for boats so it is hard to application. To solve this problem in this paper we use to a magnetic compass and GPS for suitable solar tracking system of dynamic movement and to analyze fixed and tracking solar system. frist. solar tracking device is designed two-axis control system. one-axis control system is taken a magnetic compass for making efficiency defence solar tracking sensor, two-axis control system apply GPS latitude and longitude data for SPA(Solar position algorithm) so we know the azimuth and altitude. it analyze data value of accuracy comparison from result. so the proposed algorithm confirm to have validity.

• Journal of KIISE
• /
• v.42 no.12
• /
• pp.1495-1502
• /
• 2015

Data compression involves a trade-off between delay time and data size. Greater delay times require smaller data sizes and vice versa. There have been many studies performed in the field of wireless sensor networks on increasing network life cycle durations by reducing data size to minimize energy consumption; however, reductions in data size result in increases of delay time due to the added processing time required for data compression. Meanwhile, as energy generation occurs periodically in solar energy-based wireless sensor networks, redundant energy is often generated in amounts sufficient to run a node. In this study, this excess energy is used to reduce the delay time between nodes in a sensor network consisting of solar energy-based nodes. The energy threshold value is determined by a formula based on the residual energy and charging speed. Nodes with residual energy below the threshold transfer data compressed to reduce energy consumption, and nodes with residual energy above the threshold transfer data without compression to reduce the delay time between nodes. Simulation based performance verifications show that the technique proposed in this study exhibits optimal performance in terms of both energy and delay time compared with traditional methods.

• International Journal of Computer Science & Network Security
• /
• v.24 no.4
• /
• pp.197-205
• /
• 2024

This paper presents a fully automated stand-alone irrigation system with GSM (Global System for Mobile Communication) module. Solar energy is utilized to power the system and it is aimed to conserve water by reducing water losses. The system is based on a DC water pump that draws energy from solar panels along with automated water flow control using a moisture sensor. It is also fitted with alert and protection system that consists of an ultrasonic sensor and GSM messages sender that transmits signals showing the levels of the water in the reservoir and the battery charge. The control system is designed to stop the water pump from pumping water either when the battery level drops to equal or less than 10% of its full charge, or when the water level becomes less than 10 cm high in the reservoir. The experimental results revealed that the system is appropriate to use in remote areas with water scarcity and away from the national grid.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.10
• /
• pp.4733-4739
• /
• 2012

While traditional two-axis tracking systems with double sensors had been using two sensors to control azimuth and elevation angle of the sun so that a solar cell module would make a normal line with the sun, this paper proposed a new two-axis system that can achieve the same performance with only one sensor in it. It is Two-axis tracking system that control azimuth and elevation to control to be reduced for solar cell module as proposed tracking system uses 1 sensors and the sun always forms normal. Two-axis tracking system of one sensor method that propose in paper that could reduce electric power consumption and sees than fixed type preventing action and the most efficient driving and needless drive could confirm that generation efficiency of about 23 [%] increases. To heighten efficiency of solar cell doing to receive more sunlights chasing the sun, done tracking device have proceeded a lot of studies in large size way. Therefore, is expected that will do big part in the sun tracking supply through utility study about persistent generation efficiency constructing monitoring system of the sun tracking of this paper.