• Geotechnical Engineering
• /
• v.7 no.2
• /
• pp.67-82
• /
• 1991

When bridge abutments are constructed on pile foundations in unstable slope, horizontal deflections may be developed in the piles and the abutments due to lateral soil movements arisen from backfills. In most of the above mentioned cases, the piles are situated in a soft layer where lateral earth pressures are developed between the piles and the soils. The undesirable lateral earth pressures decreases the stability of the piles. However, the piles may have a preventive effect against lateral soil movements and improve the stability of the slope. For the stability problem of such slope containing piles in a row, two kinds of analyses for the slope-stability and the pile-stability have to be performed. The whole stability of bridge abutments on pile foundation can be obtained only by the stabilization for both the slope and the piles. A reasonable analytical method for the bridge abutments on pile foundation was established in this study By use of the analytical method for an example, several factors which influence affect the stability of bridge abutment were investigated. Finally, for the bridge abutment subjected to lateral deflections damage, the fixity condition of pile head was investigated.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.2
• /
• pp.51-55
• /
• 2013

Among various construction methods, deep soil stabilization by chemical method have been widely used in order to improve soft ground. Dynamic variables using ground(such as sand, weathered granite soil and rock) -structure interaction design affected by dynamic load and cyclic load were studied a lot. However, there is something yet to learn about earthquake resistant design regarding reinforced ground by grout. Therefore, in this study using RC test, the correlation between shear strain and shear modulus with change of water content and injection rate in normal portland cement and clay was compared and analyzed by using Ramberg-Osgood model normalization As the result, dynamic coefficient was considerably affected by water content and grout injection rate.

• Journal of Korean Neurosurgical Society
• /
• v.44 no.1
• /
• pp.8-14
• /
• 2008

Objective : The purpose of this study was to determine the efficacy of short segment fixation following postural reduction for the re-expansion and stabilization of unstable burst fractures in patients with osteoporosis. Methods : Twenty patients underwent short segment fixation following postural reduction using a soft roll at the involved vertebra in cases of severely collapsed vertebrae of more than half their original height. All patients had unstable burst fracture with canal compromise, but their motor power was intact. The surgical procedure included postural reduction for 2 days and bone cement-augmented pedicle screw fixations at one level above, one level below and the fractured level itself. Imaging and clinical findings, including the level of the vertebra involved, vertebral height restoration, injected cement volume, local kyphosis, clinical outcome and complications were analyzed. Results : The mean follow-up period was 15 months. The mean pain score (visual analogue scale) prior to surgery was 8.1, which decreased to 2.8 at 7 days after surgery. The kyphotic angle improved significantly from $21.6{\pm}5.8^{\circ}$ before surgery to $5.2{\pm}3.7^{\circ}$ after surgery. The fraction of the height of the vertebra increased from 35% and 40% to 70% in the anterior and middle portion. There were no signs of hardware pull-out, cement leakage into the spinal canal or aggravation of kyphotic deformities. Conclusion : In the management of unstable burst fracture in patients with severe osteoporosis, short segment pedicle screw fixation with bone cement augmentation following postural reduction can be used to reduce the total levels of pedicle screw fixation and to correct kyphotic deformities.

• Resources Recycling
• /
• v.7 no.4
• /
• pp.55-63
• /
• 1998

The main purpose of the present study is to reduce quality variation of iron oxide for soft ferrite produced at hydrochloric acid facility )HAF) in a cold rolled mill factory. We investigated the factor of iron oxide quality variation, the operating condition of hydrochloric acid facility and the iron oxide quality with the production lot. Based on this information, we liad developed proper working plan for the diminution of iron oxide quality variation. To reduce iron oxide quality variation, the first priority is to control the picking steels, which seriously affect iron oxide quality variation, and then to separate generated waste acid. theretore, it was possible to reduce iron oxide quality variation with the proper operation of various kinds of waste acid tanks. We could produce iron oxide below 20 ppm SiO$_{2}$ content variation by operation after separation waste acid generated at TCM line.

• Journal of the Korean Society of Physical Medicine
• /
• v.17 no.4
• /
• pp.15-25
• /
• 2022

PURPOSE: This study examined the effect of bridge exercise-abdominal draw-in maneuver (ADIM) with hip adductor co-contraction on the TrA thickness and whether it is effective as a core stability exercise. METHODS: The subjects of this study, 33 men with no history in the past and who provided prior consent, were selected through interviews with male students of S University. The subjects performed five movements, including bridge exercise and ADIM, and performed two demonstrations and two exercises in advance. The abdominal muscles were measured using ultrasonography once in each movement, and the abdominal muscle tone was measured using a soft tissue tone measurement. RESULTS: There was a significant difference in the thickness between the TrA and Internal Oblique Muscles at various bridge positions (p < .05), and no significant difference with the External Oblique Muscle (p < .05). There was no significant difference in muscle tone in the Rectus abdominis part (p > .05), but a significant difference in the Oblique Muscle part (p < .05). The muscle tone of the Oblique Muscles by position showed a significant difference in Bridge, BHa, and BA compared to the rest position (p < .05), but no significant difference with BHaA (p > .05). CONCLUSION: The thickness of TrA could be increased through bridge exercise, and TrA could be activated properly using ADIM and may be an effective exercise for core stabilization.

• Journal of Korean Ophthalmic Optics Society
• /
• v.19 no.1
• /
• pp.31-42
• /
• 2014

Purpose: The present study was conducted to investigate the effect of the physical properties of RGP lens induced by lens polishing on the actual wearer's subjective comfort, the tear film break-up time and the blinking rate as a follow-up study that revealed the relationship between the lens physical properties during lens manufacturing and lens wearer's factors. Methods: RGP lenses made from the three different polishing conditions (25, 50 and 100 seconds) were applied on 28 eyes of 17 subjects, aged 20 to 29 years, without any known disease and surgical history in the eyes. While the subjects were asked to wear the RGP lenses longer than a week, the questionnaire for the comfortability was administered everyday. Subjective and objective tear break-up time and blinking rate of the wearers were further measured. Results: The wearer's subjective comfortability showed some difference in the type of discomfort and satisfaction score according to the polishing status when wearing RGP lenses made from different polishing conditions longer than a week, and a bigger difference in satisfaction score induced by polishing condition was especially shown in experienced RGP lens wearer rather than un-experienced wearer. In the case of RGP lens wearer compared with the ones without the wearing experience, as the wearing time increased subjective and objective tear break-up time were increased and the blinking rate was decreased. However, subjective and objective tear break-up time were tended to decrease with even longer wearing time when wearing the RGP lens made from the polishment for 100 seconds. Conclusions: These results confirmed that the optimization of physical properties of the lens may not give the same effect on the wearer's subjective and objective symptoms and other factors when actual wearing. From the results, it can suggest that the success rate of RGP lens wear may be changed by physiological factors such as the stabilization of wearer's tear film, comfortability and lens wearing experience when wearing RGP lens based on 'The manufacturing standard for soft contact lens/hard contact lens' provided by Korea Food and Drug Administration.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.2
• /
• pp.53-64
• /
• 2014

This study sets it's face to define effects of the various loading periods in normal consolidation area on clay's compression and long-term consolidation characteristics through a laboratory test using homogeneous remolded clay. Moreover, by carrying out a long-term consolidation test which diversifies initial consolidation applicable to effective overburden loading in the various loading period. This study intended to suggest the method predicting the final settlement on the basis of loading periods by comparing and analyzing compression curve's characteristics according to loading weight of each stage and increase in loading period when carrying out the standard consolidation test. From the test results, the study shows that as of the soft clay's compression characteristics on the basis of various loading periods, preconsolidation load has a tendency to be decreased slightly as the loading period is getting more and more longer at each step after initial consolidation load puts on the remolded clay which is caused by secondary consolidation's increase in the latter part of each phase. And those effects have an weaker influence on compression index in normal consolidation area at the same time as secondary consolidation brought out quasi-overconsolidation and stabilization of clay's structure, have an influence re-compression index is increased in overconsolidation area on the other hand.

• The Journal of Engineering Geology
• /
• v.24 no.3
• /
• pp.383-396
• /
• 2014

The condition, characteristics, and stability of slopes, as well as the consequences of slope failure, need to be understood for the proper stabilization of slopes and preclusion of potential disasters arising from slope failure. Here, a slope code system (SCS) that succinctly and accurately reflects the various conditions of a slope is proposed. The SCS represents the condition, characteristics, and geotechnical stability of slopes, as well as the consequences of slope failure, and the method is quickly and easily applied to a given slope. The SCS comprises five elements: 1) the slope material; 2) the genetic origin (rock type) and geological structure of the slope; 3) the geotechnical stability of the slope; 4) the probability of failure and remedial works made upon the slope; and 5) the consequences of failure. A letter code is selected from each element, and the result of the evaluation and classification of the slope is given as a five-letter code. Because the condition, characteristics, and geotechnical stability of a slope, as well as the consequences of slope failure, are provided by the SCS, this system will provide an effective mechanism for the maintenance and management of slopes, and will also allow more informed decision-making for determining which slopes should be prioritized for remedial measures.

• Journal of Astronomy and Space Sciences
• /
• v.21 no.4
• /
• pp.329-342
• /
• 2004

In this paper, we present preliminary feasibility studies on three types of solar observation payloads for future Korean Science and Technology Satellite (STSAT) programs. The three candidates are (1) an UV imaging telescope, (2) an UV spectrograph, and (3) an X-ray spectrometer. In the case of UV imaging telescope, the most important constraint seems to be the control stability of a satellite in order to obtain a reasonably good spatial resolution. Considering that the current pointing stability estimated from the data of the Far ultraviolet Imaging Spectrograph (FIMS) onboard the Korean STSAT-1, is around 1 arc minutes/sec, we think that it is hard to obtain a spatial resolution sufficient for scientific research by such an UV Imaging Telescope. For solar imaging missions, we realize that an image stabilization system, which is composed of a small guide telescope with limb sensor and a servo controller of secondary mirror, is quite essential for a very good pointing stability of about 0.1 arcsec. An UV spectrograph covering the solar full disk seems to be a good choice in that there is no risk due to poor pointing stability as well as that it can provide us with valuable UV spectral irradiance data valuable for studying their effects on the Earth's atmosphere and satellites. The heritage of the FIMS can be a great advantage of developing the UV spectrograph. Its main disadvantage is that two major missions are in operation or scheduled. Our preliminary investigations show that an X-ray spectrometer for the full disk Sun seems to be the best choice among the three candidates. The reasons are : (1) high temporal and spectral X-ray data are very essential for studying the acceleration process of energetic particles associated with solar flares, (2) we have a good heritage of X-ray detectors including a rocket-borne X-ray detector, (3) in the case of developing countries such as India and Czech, solar X-ray spectrometers were selected as their early stage satellite missions due to their poor pointing stabilities, and (4) there is no planned major mission after currently operating Reuven Ramaty High-Energy Solar Spectroscopic Imager (RHESSI) mission. Finally, we present a preliminary design of a solar X-ray spectrometer covering soft X-ray (2 keV) to gamma ray (10 MeV).

• Journal of the Korean Applied Science and Technology
• /
• v.30 no.4
• /
• pp.656-663
• /
• 2013

This study using yogurt of food in order to increase the conservativeness and stability of lactobacillus, to be deliciously flavored and give it visual differential effect, were described regarding making the preparing method of double matrix capsulation in food industries. Our study group was especially made to soft and moisture cream using 5wt% of sucrose ester emulsifier as first capsulation. Double matrix capsulation was formed with the best stabilized bead type capsules when it blended 1:3 ratio of chitosan and alginate. The bead diameter size was about 2.5~4mm (mean diameter: 3mm). Activity of lactobacillus containing cream for depending on various pH variations showed that alkalinity ($pH=10.3{\pm}0.3$) condition was higher than acidity ($pH=4.3{\pm}0.3$) and neutrality ($pH=7.12{\pm}0.2$) conditions. After a month, it also was certified to the activity of lactobacillus in incubated at $37^{\circ}C$ in culture medium. As application of food industry, we developed the containing lactobacillus capsule and 5 colored kinds of double matrix capsulation in yogurt cream. As for above mentioned those results, one of tool to stabilize the living lactobacillus, doubled matrix capsulation greatly be expected to contribute to food industry. Furthermore, it can be expected to apply the drug delivery system (DDS) to active ingredients of stabilizing technologies at drug and cosmetic industries.