• Progress in Superconductivity
• /
• 제14권2호
• /
• pp.99-101
• /
• 2012

Fluorescent yield X-ray absorption fine structure (XAFS) spectroscopy is useful for analyzing local structure of specific elements in matrices. We developed an XAFS apparatus with a 100-pixel superconducting tunnel junction (STJ) detector array with a high sensitivity and a high resolution for light-element dopants in wide-gap semiconductors. An STJ detector has a pixel size of $100{\mu}m$ square, and an asymmetric layer structure of Nb(300 nm)-Al(70 nm)/AlOx/Al(70 nm)-Nb(50 nm). The 100-pixel STJ array has an effective area of $1mm^2$. The XAFS apparatus with the STJ array detector was installed in BL-11A of High Energy Accelerator Research Organization, Photon Factory (KEK PF). Fluorescent X-ray spectrum for boron nitride showed that the average energy resolution of the 100-pixels is 12 eV in full width half maximum for the N-K line, and The C-K and N-K lines are separated without peak tail overlap. We analyzed the N dopant atoms implanted into 4H-SiC substrates at a dose of 300 ppm in a 200 nm-thick surface layer. From a comparison between measured X-ray Absorption Near Edge Structure (XANES) spectra and ab initio FEFF calculations, it has been revealed that the N atoms substitute for the C site of the SiC lattice.

• 한국운동역학회지
• /
• 제25권1호
• /
• pp.65-76
• /
• 2015

Objective : The purpose of this study was to analyse the differences in core stability and muscle balance of the pilates Teaser motion according to the surfaces and skills. Methods : There were 10 subjects in this study with 5 being skilled and 5 that were not skilled. The independent variables were surfaces (high elastic & aluminum) and skills (skilled & unskilled). Dependent variables were core stability and muscle balance. Core stability was measured by Force Platform (9872, Switzerland), 3D Imagery (IBS-2000, EXYMA) was used to understand the muscle balance. In order to do the Teaser movement subjects had to lay flat on their back and then lean forward as much as possible and hold the position for 10 seconds. Afterwards, they would lay back down again. A camera (MHS-PM5K, SONY) was used to make 4 phases (take off, recoil forward, holding, recoil backward) during the teaser exercise to analyze movement. In this study quantitative and qualitative analysis was used. For the statistical analysis, 2X2 ANOVA was used to analyze the differences in movement time, X,Y,Z maximum force, center of pressure and angles according to different phases. 2X3 ANOVA was used to analyze the differences in muscle balance via SPSS 18.0. Results : Soft. Elastic mat had a longer holding time, lower Fx/ Fy/ Fz, shorter Fx trajectory, larger angle and shorter gaps in muscle balance than a hard surface in skilled subjects. This was because the mat can help to recruit and then sustain core fine muscles during holding time in the Teaser movement.

• 한국터널지하공간학회 논문집
• /
• 제5권4호
• /
• pp.323-336
• /
• 2003

최근 얕은 심도를 가지는 연약한 지반에서의 터널 굴착이 요구됨에 따라 터널보강공법의 변화가 필요하게 되었다. 본 연구에서는 불량한 지반을 대상으로 한 도심지 터널에서 일반적으로 무시되는 전방 코어의 변형을 제어할 수 있는 막장 수펑보강의 효율성을 평가함으로서 터널의 안정성 향상 방안을 제시하고자 한다. 즉, 막장전방의 체계적인 사전보강으로 막장자체의 안정성을 향상시키며, 부수적으로 최종 천단변위 및 지표침하와 같은 지반거동을 억제할 수 있다. 막장의 수평보강 방법을 적용한 3차원 수치해석을 이용하여 지반조건 및 보강 조건에 따른 터널 거동 변화를 산정할 수 있었다. 결과적으로, 막장 수평보강후 막장 압출변위는 크게 줄어들며, 막장전방에 대한 보강공법과 병행할 경우 그 효과가 증가되었다. 특히, 불량한 지반일 수록 막장보강에 의한 지반거동 억제효과가 크게 나타나게 된다.

• 한국지반환경공학회 논문집
• /
• 제2권4호
• /
• pp.5-14
• /
• 2001

최근 구조물기초에 큰 변형 및 손상을 가하지 않고 안정성에 대한 정보를 비교적 쉽게 얻을 수 있는 비파괴시험(NDT, Non-Destructive Testing)기법이 큰 관심을 얻고 있다. 본 연구에서는 비파괴시험 중 검측공 기법(CSL, CT, PS)과 표면파 기법(SE, IR)을 현장타설말뚝의 건전도 평가에 이용하기 위한 적용성의 문제를 현장시험을 통하여 고찰하였다. 이를 위하여 결함이 없는 한 본의 정상말뚝과 연약선단, 단면축소 확대, 불량콘크리트 타설 등 현장에서 발생하기 쉬운 결함의 종류, 크기, 위치 등을 변화 조합한 9본의 현장타설말뚝(직경 0.4m, 길이 7.0m)을 시공하여 다양한 비파괴시험을 수행하였다. 시험을 통하여 각 기법을 현장타설말뚝의 건전도 평가에 적용할 때의 문제점과 각 기법의 합리적인 조합에 대하여 고찰하였다.

• 대한족부족관절학회지
• /
• 제8권1호
• /
• pp.86-91
• /
• 2004

Purpose: To evaluate the methods and results of the surgical treatment in the trimalleolar fracture of the ankle. Materials and Methods: We analysed the results of the ankle trimalleolar fracture which were treated with open reduction and internal fixation from January 1999 till September 2003. There were 45 patients who had at least six months follow up, 16 men, and 29 women. We have analysed the mechanism of injury, methods of operation and postoperative complications. Results: The results were assessed on ankle AP, lateral and mortise X-rays and retrospective chart review. There were 30 supination-external rotation, 13 pronation-external rotation, 2 pronation-abduction in the mechanism of injury by Lauge-Hansen classification. Cases of the posterior malleolar fracture which involved more than 25% of the weight bearing surface were 7 (15.6%). Medial malleolar mono-fixation was done in 5 cases, fibular mono-fixation in 2 cases, bimalleolar fixation in 32 cases, trimalleolar fixation in 6 cases. 38 cases (84.4%) were good or excellent in clincal assessment and 39 cases (86.7%) were good or excellent in radiological assessment according to the criteria of the Meyer. There was no difference of results among the surgical treatment methods. Conclusion: The results of our study indicate that the rigid fixation with early ankle motion and weight bearing is needed in ankle trimalleolar fracture. But minimal fixation is not bad in slight displaced fracture. Both anterior approach and posterior approach were useful methods to stabilization the posterior malleolar fracture. And pre-operative evaluation to detect the hidden soft tissue injuries and fracture mechanism is very important to avoid the failure.

• 한국해안해양공학회지
• /
• 제6권1호
• /
• pp.23-33
• /
• 1994

서해안 사질토매립지반을 대상으로 지진응답해석 및 반복삼축압축시험 결과를 통하여 지진 및 예측방법에 따른 액상화특성에 대하여 검토하였다. 지수응답해석 결과, 입력지진과 지반특성에 따라 지표면에 도달하는 최대가속도의 크기가 다르게 나타남을 알았으며 간역예측법으로 해안매립지반의 액상화 평가시 적용 가능한 지진계수를 제시하였다. N치가 작고 느슨한 상부층에 대한 액상화강도는 반복삼축압축시험 결과에 비하여 Seed법에 의한 결과가 작게 나타났고 Iwasaki 방법과 S파속도 이용법은 크거나 유사한 결과를 얻었다. 또한 간역예측법들은 상세법에 비해 액상화 가능성을 과대 평가하는 경향이 있었으며 액상화 한계심도(안전율 1일때)는 입력가속도(0.1g-0.2g)에 따라 7m-14m정도로 추정되었다.

• 대한기계학회논문집A
• /
• 제26권2호
• /
• pp.260-266
• /
• 2002

DLC films were deposited on Si wafer by RF plasma assisted CVD using CH4 gas. Tribological tests were conducted using rotating type ball on disk friction tester in dry air. Four kinds of mating balls were used. The mating balls were made with stainless steel but apply different annealing conditions to achieve different hardness conditions. Testing results in all load conditions showed that the harder the mating materials, the lower the friction coefficient among the three kind of martensite mating balls. In case of austenite balls, the friction coefficients were lower than fully annealed martensite ball. The high friction coefficient in soft martensite balls seems to be caused by the larger contact area between DLC film and ball. The wear tracks of DLC films and mating balls could have proven that effect. Measuring the wear track of both DLC films and mating balls have similar tendency comparing to the results of friction coefficients. Wear rate of austenite balls were also smaller than that of fully annealed martensite ball. The results of effect of applying load showed, the friction coefficients were become decrease when the applying loads exceed critical load conditions. The wear track of mating balls showed that some material transfer occurs from DLC film to mating ball during the high friction process. Raman spectra analysis showed that transferred material was a kind of graphite and contact surface of DLC film seems to undergo phase transition from carbon to graphite during the high friction process.

• 대한기계학회논문집 C: 기술과 교육
• /
• 제2권2호
• /
• pp.73-80
• /
• 2014

상기도 내의 약물 전달을 알아보기 위하여 구강 호흡 시 공기유동에 대한 수치해석을 수행하였다. 상기도는 구강과 후두, 기관과 기관지로 구성되어 있다. 정밀 촬영한 CT 데이터로부터 의료영상 소프트웨어(Mimics)를 이용한 구분(segmentation)과 세심한 표면처리를 통하여 해부학적으로 정확한 모델을 만들 수 있었다. 이 3차원 컴퓨터 모델을 이용하여, 구강에서 기관지의 2번째 분지까지 이르는 유로의 수치 모델을 제작하였다. 수치해석은 상용 소프트웨어인 ANSYS/Fluent를 이용하여 계산하였다. 본 연구에 사용된 모델은 노즐이 부착되지 않은 상태에서 초당 250 mL를 흡입하는 정상 구강호흡 모델과 입구에 각각 20 mL/s, 40 mL/s, 60 mL/s의 유량을 갖는 노즐을 장착한 모델을 사용하였다. 전산 유동가시화 결과로부터, 노즐의 유량을 증가시킬수록 선회류의 발생 정도가 증가하여 구강 내 약물의 잔류 량은 증가하지만, 기관/기관지에 약물 도표는 균일하게 나타났다.

• Archives of Reconstructive Microsurgery
• /
• 제8권1호
• /
• pp.56-63
• /
• 1999

저자들은 1994년부터 1997년까지 수부에 급성 연부조직 손실과 신근건 결손을 가진 2명의 환자에 대해 지연처치후 동맥화된 족배 정맥 건피판술을 시행하였다. 피판의 생존 표면적은 2명 모두 100%였다. 피판 크기는 각각 $10{\times}10cm,\;6{\times}6cm$였다. 술후 2주째 능동적 굴곡운동과 수동적 신전 운동을 시작하였고 점진적인 저항운동을 5주간 실시하였다. 피판은 수부의 정상 피부와 비슷한 색깔과 피부상태를 보였다. 지연처치후 동맥화된 정맥 건피판은 순수 정맥피판이나 동맥화된 정맥피판보다 큰 피판을 만들 수 있으며 동맥화후 정맥피판의 생존율을 높여 복합 피판이 가능하게 하며 공여부의 주 동맥을 보존할 수 있고 얇은 조직을 얻을 수 있으며 피판을 심부 박리 없이 쉽게 거상할 수 있는 장점을 가진다. 단점으로는 두 단계의 수술이 필요하고 공여부 반흔과 족지의 신전이 약해질 수 있다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.369-372
• /
• 2002

In this research, a vision system for detecting tool breakage which is hardly detected by such indirect in-process measurement method as acoustic emission, cutting torque and motor current was developed and embedded into a PC-NC system. The vision system consists of CMOS image sensors, a slit beam laser generator and an image grabber board. Slit beam laser was emitted on the tool surface to separate the tool geometry well from the various obstacles surrounding the tool. An image of tool is captured through two steps of signal processing, that is, median filtering and thresholding and then the tool is estimated normal or broken by use of change of the centroid of the captured image. An air curtain made by the jetting high-pressure air in front of the lens was devised to prevent the vision system from being contaminated by scattered coolant, cutting chips in cutting process. To embed the vision system to a Siemens PC-NC controller 840D NC, an HMI(Human Machine Interface) program was developed under the Windows 95 operating system of MMC103. The developed HMI is placed in a sub window of the main window of 840D and this program can be activated or deactivated either by a soft key on the operating panel or M codes in the NC part program. As the tool breakage is detected, the HMI program emit a command for automatic tool change or send alarm to the NC kernel. Evaluation test in a high speed tapping center showed the developed system was successful in detection of the small-radius tool breakage.