• Korean Journal of Materials Research
• /
• v.19 no.4
• /
• pp.203-206
• /
• 2009

$Sn_XSe_{100-X}$ (15|X|30) alloys have been studied to explore their suitability as phase change materials for nonvolatile memory applications. The phase change characteristics of thin films prepared by a Radio Frequency (RF) magnetron co-sputtering system were analyzed by an X-ray diffractometer and 4-point probe measurement. A phase change static tester was also used to determine their crystallization under the pulsed laser irradiation. X-ray diffraction measurements show that the transition in sheet resistance is accompanied by crystallization. The amorphous state showed sheet resistances five orders of magnitude higher than that of the crystalline state in $Sn_XSe_{100-X}$ (x = 15, 20, 25, 30) films. In the optimum composition, the minimum time of $Sn_XSe_{100-X}$ alloys for crystallization was 160, 140, 150, and 30ns at 15mW, respectively. The crystallization temperature and the minimum time for crystallization of thin films were increased by increasing the amount of Sn, which is correlated with the activation energy for crystallization.

• Journal of the Korean institute of surface engineering
• /
• v.44 no.5
• /
• pp.185-189
• /
• 2011

$Cu_2ZnSnSe_4$ thin films for solar absorber application were prepared by pulsed laser deposition of a synthesized $Cu_2ZnSnSe_4$ compound target. The film's composition revealed that the deposited films possess an identical composition with the target material. Further film compositional control toward a stoichiometric composition was performed by optimizing substrate temperature, deposition time and target rotational speed. At the optimum condition, X-ray diffraction patterns of films showed that the films demonstrated polycrystalline stannite single phase with a high degree of (112) preferred orientation. The absorption coefficient of $Cu_2ZnSnSe_4$ thin films were above 104 cm.1 with a band gap of 1.45 eV. At an optimum condition, films were identified as a p type semiconductor characteristic with a resistivity as low as $10^{-1}{\Omega}cm$ and a carrier concentration in the order of $10^{17}cm^{-3}$.

• Proceeding of EDISON Challenge
• /
• 2017.03a
• /
• pp.404-411
• /
• 2017

이 논문에서는 2차원 화합물 반도체인 Indium Selenide monolayer의 효과적인 도펀트 원소를 탐색해보았다. 총 4가지 종류의 원소를 도핑시켜 계산을 했다. In 자리에 Mg과 Sn을 도핑시켜 각각 p-type과 n-type으로 만들고 Se 자리에 As과 Br을 도핑시켜 각각 p-type과 n-type으로 만들었다. 변화한 성질을 알아보기 위해 전자 구조를 분석하고 band structure와 DOS를 살펴보았다. P-type 같은 경우, Mg doped InSe는 shallow defect level이 생겨 좋은 반도체로 쓰일 수 있지만 As을 도핑한 InSe는 deep defect states가 생겼다. VBM에서 약 0.67 eV만큼 떨어져있는데 이 수치는 실험값과 비슷한 값이다. N-type 경우에는 Sn doped InSe는 deep defect states가 생겼고, CBM 아래로 약 0.08eV만큼 defect가 생긴 것이 실험값과 비슷하다. Br doped InSe는 Sn doped InSe보다 안정적인 n형 반도체가 될 수 있다.

• Current Photovoltaic Research
• /
• v.3 no.2
• /
• pp.54-60
• /
• 2015

ZnSnO thin films were deposited by atomic layer deposition (ALD) process using diethyl zinc ($Zn(C_2H_5)_2$) and tetrakis (dimethylamino) tin ($Sn(C_2H_6N)_4$) as metal precursors and water vapor as a reactant. ALD process has several advantages over other deposition methods such as precise thickness control, good conformality, and good uniformity for large area. The composition of ZnSnO thin films was controlled by varying the ratio of ZnO and $SnO_2$ ALD cycles. The ALD ZnSnO film was an amorphous state. The band gap of ZnSnO thin films increased as the Sn content increased. The CIGS solar cell using ZnSnO buffer layer showed about 18% energy conversion efficiency. With such a high efficiency with the ALD ZnSnO buffer and no light soaking effect, AlD ZnSnO buffer mighty be a good candidate to replace Zn(S,O) buffer in CIGSsolar cells.

• Current Photovoltaic Research
• /
• v.10 no.2
• /
• pp.33-38
• /
• 2022

Planner configuration thin film solar cells (TFSCs) with SnS/CdS heterojunction performed a lower short-circuit current (J_SC). In this study, we have demonstrated a path to overcome deficiency in J_SC by the incorporation of Se in the SnS absorber. We carried out the incorporation of Se in VTD grown SnS absorber by rapid thermal annealing (RTA). The diffusion of Se is mostly governed by RTA temperature (T_RTA), also it is observed that film structure changes from cube-like to plate-like structure with T_RTA. The maximum J_SC of 23.1 mA cm^-2 was observed for 400℃ with an open-circuit voltage (V_OC) of 0.140 V for the same temperature. The highest performance of 2.21% with J_SC of 18.6 mA cm^-2, V_OC of 0.290 V, and fill factor (FF) of 40.9% is observed for a T_RTA of 300℃. In the end, we compare the device performance of Se- incorporated SnS absorber with pristine SnS absorber material, increment in J_SC is approximately 80% while a loss in V_OC of about 20% has been observed.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.86.1-86.1
• /
• 2010

Cu2ZnSnSe4는 CIS 태양전지의 In 대체 물질계로 주목을 받고 있는 저가형 태양전지 재료로 장차 차세대 태양전지 재료로 응용이 기대되고 있다. 그러나 에너지 밴드갭이 0.9~1.1eV로 다소 낮아 태양전지 광흡수층 재료로 사용하기 위해서는 wide band gab화 처리가 필요하다. 본 연구에서는 CZTSe에 S를 첨가하여 에너지 밴드갭을 확장하고자 하며, S의 첨가가 CZTSe 박막의 특성에 미치는 영향에 대하여 조사하였다. 실험의 편의성을 도모하고자 펄스레이저 법을 사용하여 증착하였다. 박막 조성 제어에는 Cu, Zn, Sn, Se, S 분말을 볼밀로 분쇄, 혼합하여 균질 혼합상 프리커서를 제조하고 이를 Cold Isostatic Press(CIP) 성형하여 Source target을 사용하였다. Pulsed YAG-Laser를 사용하여 soda lime glass상에 증착하고 조성, 구조, 조직을 관찰하고 에너지 밴드갭, 광흡수계수, 면저항, 전하밀도 등 특성을 조사하였다.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.42.1-42.1
• /
• 2011

높은 광흡수 계수를 갖는Cu(In,Ga) $Se_2$ (CIGS) 화합물 박막 소재는 고효율 태양전지 양산을 위해 가장 전도유망한 재료이나 상대적으로 매장량이 적은 In 및 Ga을 사용한다는 소재적 한계가 있다. $Cu_2ZnSnSe_4$ (CZTSe) 혹은 $Cu_2ZnSnS_4$(CZTS)와 같은 Cu-Zn-Sn-Se계 화합물 반도체는 CIGS 내 희소원소인 In과 Ga이 범용원소인 Zn 및 Sn으로 대체된 소재로써 미래형 저가 태양전지 개발을 위해 활발히 연구되고 있는데, 그 화합물 조합에 따라 0.8 eV부터 1.5 eV까지의 에너지 밴드갭을 갖는 것으로 알려져 있다. 스퍼터링법에 기반한 2단계 공정에 의해 3.2%의 CZTSe 및 6.7%의 CZTS 태양전지 효율 달성이 보고된 바 있으며, 최근 비진공 방식을 이용하여 제조된 $Cu_2ZnSn(S,Se)_4$ (CZTSSe) 태양전지가 9.6%의 변환효율을 생산하여 세계 최고기록을 갱신한 바 있다. 반면, 동시진공증발법에 의한 Cu-Zn-Sn-Se계 연구는 박막 조성 조절이 상대적으로 용이하다는 장점에도 불구하고, 상대적으로 공개된 연구결과의 양이 적으며 그 효율에 대한 보고는 특히 미미하다. 본 연구에서는 동시진공증발법에 의한 CZTSe 박막 연구 결과를 바탕으로 Sn 손실을 최소화하기 위한 진공증발 공정을 최적화하였으며, 이를 통해 CZTSe 박막 태양전지를 제조하고 그 특성분석을 통해 5% 이상의 변환효율을 달성하였다.

• Korean Journal of Materials Research
• /
• v.28 no.10
• /
• pp.564-569
• /
• 2018

$Cu_2ZnSn(S,Se)_4$ (CZTSSe) films were prepared on Mo coated soda lime glass substrates by sulfo-selenization of sputtered stacked Zn-Sn-Cu(CZT) precursor films. The precursor was dried in a capped state with aqueous NaOH solution. The CZT precursor films were sulfo-selenized in the S + Se vapor atmosphere. Sodium was doped during the sulfo-selenization treatment. The effect of sodium doping on the structural and electrical properties of the CZTSSe thin films were studied using FE-SEM(field-emission scanning electron microscopy), XRD(X-ray diffraction), XRF(X-ray fluorescence spectroscopy), dark current, SIMS(secondary ion mass spectrometry), conversion efficiency. The XRD, XRF, FE-SEM, Dark current, SIMS and cell efficiency results indicated that the properties of sulfo-selenized CZTSSe thin films were strongly related to the sodium doping. Further detailed analysis and discussion for effect of sodium doping on the properties CZTSSe thin films will be discussed.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.130-133
• /
• 2009

$Cu_2ZnSnSe_4$(CZTSe) is one of the promising materials for the solar cell due to its abundant availability in the nature. In this study, we report the fabrication of CZTSe thin film by Pulsed Laser Deposition(PLD) method using quaternary compound target on sodalime glass substrate. The quaternary CZTSe compound target was synthesized by solid state reaction method using elemental powders of Cu, Zn, Sn and Se. Powders were milled in high purity ethanol using zirconia ball with mixed size of 1 and 3 mm at the same proportions for 72 hours milling time. The structural, chemical and mechanical properties of the synthesized CZTSe powders were investigated prior to the deposition process. The CZTSe compound powder, and $500^{\circ}C$ of sintering temperature shows the best properties for PLD target. Results show that the as-deposited CZTSe thin films with the precursors by PLD have a composition near-stoichiometric.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.11
• /
• pp.3403-3406
• /
• 2010