• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.12
• /
• pp.949-954
• /
• 2011

In this study, the characteristics and error ranges of the mechanical bonding strength were analyzed according to before and after thermal shock test for various chips of automotive application component using Sn-3.0Ag-0.5Cu solder. In the after thermal shock test, the mechanical bonding strengths tend to decrease, meanwhile decreasing rates of mechanical strengths were less then 12% at specimen's bonding area below 3.5$mm^2$, and were from 17 to 21% at specimen's bonding area above 12 $mm^2$. On the other hand, Specimen's mean deviation rates were about 5% at specimen's bonding area more than 12 $mm^2$. Inversely, at specimen's bonding area is less then 3.5 $mm^2$, mean deviation rates were increased to about 8%. It means that the smaller device size is, the larger mean deviation rate. In addition, error ranges and deviation rates of the mechanical bonding strengths may differ slightly depending on their bonding area. Furthermore, process conditions as well as method of mechanical reliability evaluation should be established to reduce the error ranges of bonding strength.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.77-77
• /
• 2010

본 연구에서는 Sn-3.0Ag-0.5Cu (SAC305) 무연솔더의 최적 인쇄성을 위한 PCB 및 마스크설계, 스크린프린팅 공정변수의 최적값을 실험계획법을 통해 평가하였다. 사용된 칩은 가로 0.4mm 세로 0.2mm의 0402 MLCC칩이며, 사용된 시험보드는 OSP 표면처리된 PCB이었다. 인쇄성을 판단하기 위한 공정인자는 금속마스크 두께, 마스크홀 크기, 패드크기 및 모양, 인쇄각도, 인쇄속도, 판분리속도이었다. ANOVA분석을 통해 주인자를 파악하였으며, 인쇄성에 영향을 미치는 주인자는 마스크두께와 인쇄각도임이 확인되었다. 그 후 중심 합성법을 이용하여 인쇄성 최적 조건을 확인하였다. 결과로 나타난 등고선/표면도를 통해, 마스크두께가 작을 때에는 인쇄각도가 작아야 높은 인쇄성을 갖으며, 또한 마스크 두께가 클 경우에는 인쇄각도가 커야 높은 인쇄성을 가짐을 알 수 있었다. 추가실험을 통해서 인쇄성 표면도의 정확도를 확인하였으며, 실험값은 표면도에서 표시된 인쇄성값과 비슷함을 알 수 있었다. 또한, 인쇄성이 낮은 영역과 높은 영역에서 접합강도값을 측정하였으며, 인쇄성이 좋은 영역에서 접합강도도 높음을 알 수 있었다.

• Journal of Welding and Joining
• /
• v.17 no.3
• /
• pp.90-95
• /
• 1999

The increase in high speed, multi-function and high I/O pin semiconductor devices highly demands high pin count, very thin, and high density packages. BGA is one of the solutions, but the package has demerits in package reliability, surface mounting problems due to the PCB warpage and solder joint crack related with TCE mismatch between the materials. On this study to verify the thermal fatigue lifetime of the solder joint FEM and experiments were performed after surface mounting BGA with different solder composition and reliability conditions. FEM showed optimum composition of Ag3.2-Sn96.5 and under the composition minimum creep deformation of the solder joint was calculated, and the thermal fatigue lifetime was improved. In view of temperature cycle condition, the conditions of $-65^{\circ}C$to $150^{\circ}C$ showed minimum lifetime and t was 1/3 of $0^{\circ}C$ to $125^{\circ}C$ condition. Test board was prepared and solder joint crack was verified. Until 1000cycle on soder joint crack was observed.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.19 no.6
• /
• pp.547-557
• /
• 1986

The characteristics of the three alkaline proteinases, Enz. A, B and C, from the pyloric caeca of mackerel have been investigated. The optimum condition for the activity of the Enz. A, B and C was pH 9.4, 9.8 and 9.8 at $45^{\circ}C$ for $2\%$ casein solution, and was pH 9.2 10.2 and 9.8 at $45^{\circ}C$ for $5\%$ hemoglobin denatured by urea, respectively. Enz. A, B and C by heat treatment at $50^{\circ}C$ for 5 min were inactivated 90, 33 and $37\%$, respectively, over the original activity. The reaction rate of the three alkaline proteinases was constant to the reaction time to 40 min in the reaction condition of $2{\mu}g/ml$ of enzyme concentration and $2\%$ casein solution. The reaction rate equation and Km value against casein substrate determined by the method of Lineweaver and Burk were: Enz. A, Y=3.6X and $Km=5.0{\times}10^{-3}\%$; Enz. B, Y=6.0X and $Km=1.0{\times}10^{-3}\%$; Enz. C, Y=4.2X and $Km=3.6{\times}10^{-3}\%$. The three alkaline proteinases were inactivated by $Ag^+$ and $Hg^{2+}$, but activated by $Mn^{2+},\;Sn^{2+}\;and\;Pb^{2+}$, Enz. B and C were remarkably inhibited by the soybean trypsin inhibitor. Molecular weight of Enz. A, B and C determined by SDS-polyacrylamide gel electrophoresis and Sephadex G-100 gel filtration was in the range of $27,500{\pm}2,500,\;20,500{\pm}1,500\;and\;15,250{\pm}250$, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.4
• /
• pp.237-240
• /
• 2016

The improvement of irradiation intensity and irradiation uniformity is essential for large area and high power UVA light source application. In this study, large number of chips bonded by micro soldering technique were driven by low current, and current limiting diodes were configured to supply constant current to parallel circuits consisting of large number of series strings. The dimension of light source module circuit board was $350{\times}90mm^2$ and 16,650 numbers of 385 nm flip chip LEDs were used with a configuration of 90 parallel and 185 series strings. The space between LEDs in parallel and series strings were maintained at 1.9 mm and 1.0 mm distance, respectively. The size of the flip chip was $750{\times}750{\mu}m^2$ were used with contact pads of $260{\times}669{\mu}m^2$ size, and SAC (96.5 Sn/3.0 Ag/0.5 Cu) solder was used for flip chip bonding. The fabricated light source module with 7.5 m A supply current showed temperature rise of $66^{\circ}C$, whereas irradiation was measured to be $300mW/cm^2$. Inaddition, 0.23% variation of the constant current in each series string was demonstrated.

• Restorative Dentistry and Endodontics
• /
• v.9 no.1
• /
• pp.81-87
• /
• 1983

The purpose of this study was to observe and identify the phases of amalgam and to know the transformation of microstructure in the set amalgam by lapse of time. In this study, shofu spherical-D alloy was used. After trituration of amalgam alloy and mercury (Wig-L-Bug), it was filled in the stone dies. This specimens being polished and etched by usual method was observed under optical microscope using metallurgical microscope. And then X-ray diffractometer was used to analyze the phases contents and transformation of microstructure at $2{\frac{1}{2}}$ hours, 15 hours, 28 hours and 2 years after being amalgamated. The following results were obtained: 1. Shofu spherical-D alloy powder was composed of ${\gamma}$ phase, ${\epsilon}$phase and Ag-Cu eutectic phases. 2. ${\gamma}_2$ phases were appeared at $2{\theta}$ values ($32.0^{\circ}$ and $43.8^{\circ}$) in the amalgam which was analyzed at $2{\frac{1}{2}}$ hours and 15 hours after trituration with mercury. 3. In the amalgam at 28 hours, ${\gamma}_2$ phase was found at $2{\theta}$ value ($43.8^{\circ}$) at 35 hour, $r_2$ phase was appeared at $2{\theta}$ value $32.0^{\circ}$. 4. No ${\gamma}_2$ phases were observed in the 2 years old amalgam. But ${\eta}$ ($Cu_6Sn_5$) phases were found at $2{\eta}$ values $29.4^{\circ}$ and $42.4^{\circ}$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.245-245
• /
• 2012

차세대 디스플레이로 각광받고 있는 AMOLED에 대한 관심이 높아짐에 따라 구동 소자의 연구가 활발히 이루어지고 있다. 산화물 반도체 박막 트랜지스터는 비정질 실리콘 박막 트랜지스터에 비해 100 $cm^2$/Vs 이하의 높은 이동도와 우수한 전기적 특성으로 AMOLED 구동 소자로서 학계에서 입증되어왔고, 현재 여러 기업에서 산화물 반도체를 이용한 박막 트랜지스터 제작 연구가 활발히 이루어지고 있다. 본 연구는 열처리 조건을 가변하여 제작한 산화물 반도체 박막 트랜지스터의 전기적 특성 분석을 목적으로 한다. 실리콘 기판에 oxidation 공정을 이용하여 SiO2 100 nm, DC스퍼터링을 이용하여 ITZO (Indium-Tin-Zinc Oxide) 산화물 반도체 박막 50 nm, 증착된 산화물 반도체 박막의 열처리 후, evaporation을 이용하여 source/drain 전극 Ag 150 nm 증착하여 박막 트랜지스터를 제작하였다. 12 sccm의 산소유량, 1시간의 열처리 시간에서 열처리 온도 $400^{\circ}C$, $200^{\circ}C$의 샘플은 각각 이동도 $29.52cm^2/V{\cdot}s$, $16.15cm^2/V{\cdot}s$, 문턱전압 2.61 V, 6.14 V, $S{\cdot}S$ 0.37 V/decade, 0.85 V/decade, on-off ratio 5.21 E+07, 1.10 E+07이었다. 30 sccm의 산소유량, 열처리 온도 $200^{\circ}C$에서 열처리 시간 1시간, 1시간 30분 샘플은 각각 이동도 $12.27cm^2/V{\cdot}s$, $10.15cm^2/V{\cdot}s$, 문턱전압 8.07 V, 4.21 V, $S{\cdot}S$ 0.89 V/decade, 0.71 V/decade, on-off ratio 4.31 E+06, 1.05 E+07이었다. 산화물 반도체의 열처리 효과 분석을 통하여 높은 열처리 온도, 적은 산소의 유량, 열처리 시간이 길수록 이동도, 문턱전압, $S{\cdot}S$의 산화물 박막 트랜지스터 소자의 전기적 특성이 개선되었다.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.2
• /
• pp.91-97
• /
• 2022

The wettability and rheological properties of solder paste with the size of the solder powder were evaluated. To formulate the solder paste, three types of solder powder were used: T4 (20~28 ㎛), T5 (15~25 ㎛), and T6 (5~15 ㎛). The viscosities of the T4, T5, and T6 solder pastes at 10 RPM were 155, 263, and 418 Pa·s, respectively. After 7 days, the viscosity of the T4 solder paste slightly increased by 2.6% and that of T5 was increased by 20.6%. The viscosity of the T6 solder paste after 7 days could not be measured due to high viscosity. The viscosity variation with solder particle size also affected on the printability of the solder. In the case of the T4 solder paste, printability, slump, bridging, and soldering properties were excellent. On the other hand, T5 showed slight dewetting and solder ball defects. Especially, T6, which the smallest powder size, showed poor printability and dewetting at the edge of solder.

• Journal of the Microelectronics and Packaging Society
• /
• v.22 no.2
• /
• pp.55-59
• /
• 2015

Novel low-volume solder-on-pad (SoP) process is proposed for a fine pitch Cu pillar bump interconnection. A novel solder bumping material (SBM) has been developed for the $60{\mu}m$ pitch SoP using screen printing process. SBM, which is composed of ternary Sn-3.0Ag-0.5Cu (SAC305) solder powder and a polymer resin, is a paste material to perform a fine-pitch SoP in place of the electroplating process. By optimizing the volumetric ratio of the resin, deoxidizing agent, and SAC305 solder powder; the oxide layers on the solder powder and Cu pads are successfully removed during the bumping process without additional treatment or equipment. The Si chip and substrate with daisy-chain pattern are fabricated to develop the fine pitch SoP process and evaluate the fine-pitch interconnection. The fabricated Si substrate has 6724 under bump metallization (UBM) with a $45{\mu}m$ diameter and $60{\mu}m$ pitch. The Si chip with Cu pillar bump is flip chip bonded with the SoP formed substrate using an underfill material with fluxing features. Using the fluxing underfill material is advantageous since it eliminates the flux cleaning process and capillary flow process of underfill. The optimized interconnection process has been validated by the electrical characterization of the daisy-chain pattern. This work is the first report on a successful operation of a fine-pitch SoP and micro bump interconnection using a screen printing process.

• Economic and Environmental Geology
• /
• v.12 no.2
• /
• pp.79-93
• /
• 1979

Twenty five samples of the scheelite-powellite series from twelve Korean tungsten deposits of various geologic settings were studied mineralogically and geochemically. Variations in the trace-element contents of the scheelite minerals are considered in relation to geologic settings and mineralogic properties. Scheelites from ore deposits developed in similar geologic settings and under similar physicochemical conditions are characterized by specific combinations of trace elements.