• Journal of Environmental Health Sciences
• /
• v.32 no.4 s.91
• /
• pp.292-303
• /
• 2006

The Volatile Organic Compounds(VOCs) are emitted from various sources and have lots of different form. Recently human are spending the many times at indoor area and indoor air pollution is issued the important social problem. The emission sources of indoor air pollutants are very various, also indoor building materials are composed of very complex chemical compounds, these indoor building materials discharge very much VOCs and other hazardous compounds. In this study, we performed the small chamber test to investigate the VOCs emission concentration and characteristics involving five kinds of the indoor building materials(furniture material, wooden floor, wall paper, paint and tile) under different conditions of four temperature and relative humidity as account of the air flow rate(AFR), air exchange rate(AER), loading factor and air velocity respectively. As the result, It was showed that building materials are emitted the highest VOCs concentration at the beginning of experiment and furniture material is emitted the highest VOCs concentration. Most of the materials were affected by temperature, but paint and tile material were affected by humidity.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.821-824
• /
• 2005

Probe storage is one of the strong candidates for future mobile storage device since it has potential of recording density over I $Tb/in^2$ with r/w speed over 100 Mbps. It also uses silicon-processing technology that suits the purpose of small form factor. In this paper, write characteristics of resistive probe that can rotate the field direction of PZT by field-induced resistance changes in a small resistive region at the apex of the tip will be presented. Also, the relationship between the size of tip and the available write width is investigated for different source bias conditions. For this study, two-dimensional computer simulation ($SILVACO^{TM}$) was performed. With optimum design, the width of the writing electric field can be smaller than 50nm

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.484-487
• /
• 2006

In this paper, linear ultrasonic actuators are designed using two dimensional motions of a PMW-PT piezoelectric plate. By equalizing the natural frequencies of longitudinal and transverse vibration modes in the cantilever structure, the ultrasonic motion of the combined vibration modes are generated. We have designed two different PMN-PT actuators: one uses a tip attached on the edge of the actuator and it drives the object in the perpendicular direction of the tip. In other model, the actuator plate moves itself through stationary guides. Prototypes of the two models are manufactured and experiments results are compared to the theoretical and numerical results. The effects of structural characteristics and the friction force existing between the actuator tip and the moving object are considered. Experiments show the possibility of small size ultrasonic linear motors which can be applicable to small form factor information storage and phone camera actuators.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.384-387
• /
• 2006

Vertical L/UL (Load/Unload) velocity is very important parameter to determine the L/UL performance, and the vertical velocity is determined by the actuator velocity and the ramp profile. However, it is not easy to precisely control the actuator rotating velocity during the L/UL process. Especially in emergency parking, servo system doesn't operate, it is impossible to control an actuator velocity. Then, the vertical unloading velocity depends on only ramp profile. The ramp height and the sliding length for L/UL process in SFF (Small Form Factor) HDD are restricted due to slimness and small media. For these reasons, it is very difficult to design the ramp profile in SFF HDD. Therefore, this study analyzes the unloading dynamic characteristics for various ramp profiles and makes the thesis for ramp profile design.

• Structural Engineering and Mechanics
• /
• v.17 no.1
• /
• pp.69-85
• /
• 2004

The novel form of composite walling system consists of two skins of profiled steel sheeting with an in-fill of concrete. Such walling system can be used as shear elements in steel framed building subjected to lateral load. This paper presents the results of small-scale model tests on composite wall and its components manufactured from very thin sheeting and micro-concrete tested under monotonic and cyclic shear loading conditions. The heavily instrumented small-scale tests provided information on the load-deformation response, strength, stiffness, strain condition, sheet-concrete interaction and failure modes. Analytical models for shear strength and stiffness are derived with some modification factor to take into account the effect of quasi-static cycling loading. The performance of design equations is validated through experimental results.

• Transactions of the Society of Information Storage Systems
• /
• v.2 no.2
• /
• pp.150-155
• /
• 2006

Vertical L/UL (Load/Unload) velocity is very important parameter to determine the L/UL performance, and the vertical velocity is determined by the actuator velocity and the ramp profile. However, it is not easy to precisely control the actuator rotating velocity during the L/UL process. Especially in emergency parking, servo system doesn't operate, it is impossible to control an actuator velocity. Then, the vertical unloading velocity depends on only ramp profile. The ramp height and the sliding length for L/UL process in SFF (Small Form Factor) HDD are restricted due to slimness and small media. For these reasons, it is very difficult to design the ramp profile in SFF HDD. Therefore, this study analyzes the unloading dynamic characteristics for various ramp profiles and makes the thesis for ramp profile design.

• The Research Journal of the Costume Culture
• /
• v.8 no.2
• /
• pp.282-292
• /
• 2000

The purpose of this study is to provide for some basic data useful to the development of the brassieres comfortable and more suitable for obese women. The results of this study can be summarized as follows ; 1. Obese women were categorized using Rohrer index into three groups, and thereupon, their breast forms were analyzed. As a result, it was found that group 1 and 2 had similar small breasts, while group 3 had the largest size of breasts. 2. The forms of obese women's breast split, protrusion and volume, factors related with breast area and drooping, factor affecting the breast protrusion and factor defining the lower form of breast. 3. The actual breast types of obese women could be classified into cone type, protrusion type, drooping type Ⅰ and Ⅱ. The more obese a woman was, her breast tended more to droop.

• Journal of Periodontal and Implant Science
• /
• v.43 no.6
• /
• pp.276-282
• /
• 2013

Purpose: The aim of this study was to explore root shape abnormalities, to investigate the influence of root form abnormalities on periodontal attachment loss, and to gather basic data to assist in the diagnosis and treatment of aggressive periodontitis. Methods: From January 2010 to June 2012, a survey was conducted of all 3,284 periodontitis patients who visited the Department of Periodontology, Daejeon Dental Hospital, Wonkwang University School of Dentistry. Clinical parameters (probing depth, periodontal attachment loss, missing teeth) were measured and a radiographic examination was performed at the baseline. We classified the root shape abnormality of bicuspids and molars based on Meng classification. Results: The periodontal attachment loss was the highest at the maxillary first molar (6.03 mm). The loss of the second molar was prominent. Type V deformity was shown to be the most common in the second maxillary and mandibular molars (P<0.05). Type V root shape was associated with the highest attachment loss (P=0.01). Conclusions: Considering the small population and limited design of this study, definitive conclusions cannot be drawn. We suggest larger scale, methodologically more sophisticated studies that include normal controls and chronic periodontitis patients to clarify whether root form abnormalities are a potential risk factor for aggressive periodontitis.

• Journal of The Korea Institute of Healthcare Architecture
• /
• v.11 no.3
• /
• pp.75-85
• /
• 2005

Recently the number of women's hospitals of a small scale are increasing in seoul and the other cities although the surroundings of these sites are so inferior. Those hospitals need the space of comfort as like family home. This study suggests that the encirclement space is one of the design methods to make comfort to patients. The encirclement is the form of hugging a baby to a mother's arms. Analysing six woman hospitals, encirclement space is categorized about the six types of square, open square, right-angled, linear, dispersed, etc. The characteristics of "right-angled" is featured as the form of L, and "square" type is characterized as the relationship of functional circulation among doctors, nurses and patients. And all types are organized as the relationship between the encirclement space and the enclosed space about how the functional space and the comfort space are made up. The properties of encirclement space are appeared by the interactions about function, circulation, sight, form, access, recognition through transparent, three-dimensional experience, etc. Encirclement space is recommended as a vital factor to make comfort space for designing women's hospital in city.

• Journal of Fisheries and Marine Sciences Education
• /
• v.24 no.1
• /
• pp.34-43
• /
• 2012

In order to establish order in fishing industry by cracking down on illegal fishing vessels effectively, it is an essential requirement to identify marking such as the name of fishing vessel and a port of register more easily. Accordingly, it is quite natural that markings on fishing vessels should be marked clearly in an appropriate size on an appropriate site in order for them to be distinguished on the air such as from planes as well as on the sea. Actually, when examining marks such as the name of a vessel which are operating in the country, marks of most fishing vessels are too small as they cannot be distinguished with the naked eye even very closely. There is no coastal fishing vessel which marks the name of fishing vessel on the upper part in order to distinguish it from planes. Fishing vessel law generally which regulates the basic laws about shipbuilding regulates marks on fishing vessel, and fisheries law only regulates sign boards of fishing vessels. Problems and improvement of the marking system on fishing vessels suggested by this paper are as follows. First, in order to contribute to establish order in fishing industry, it would be desirable to tighten standards in fisheries law besides the fishing vessel law. Second, it is difficult to distinguish marks such as the name of a vessel as relevant laws allow fishers to make such marks too small. It is necessary to set the standard for marks larger than those regulated by the international treaty. Third, the relevant laws do not regulate a letter form of marks. Therefore, it becomes a factor to make small marks hard to be distinguished more. It is necessary to decide a clear letter form. Fourth, there is insufficient detailed international standards about the marking system. It is necessary to regulate a detailed standard.