• Journal of the Semiconductor & Display Technology
• /
• v.23 no.2
• /
• pp.65-70
• /
• 2024

Using a computational fluid dynamics(CFD) simulation tool, we have provided a coating guideline for slot-die coating with a double layer slot die head. We have analyzed the fluid dynamics in terms of the coating speed, flow rate ratio, and viscosity ratio, which are critical for the stability of coating meniscus. We have identified the common coating defects such as break-up, air entrainment, and leakage by varying the coating speeds. The flow rate ratio is the critical parameter determining the wet film thickness of the top and bottom layers. It is shown that when the flow rate ratio exceeds or equals 1.8, air entrainment occurs due to insufficient hydraulic pressure in the bottom layer, even though the total flow rate remains constant. Furthermore, we have found that the flow of the bottom layer is significantly affected by the viscosity of top layer. The viscosity ratio of 4 or higher obstructs the flow of the bottom layer due to the increased hydraulic resistance, resulting in leakage. Finally, we have demonstrated that as the viscosity ratio increases from 0.1 to 10, the maximum coating speed rises from 0.4 mm/s to 1.6 mm/s, and the minimum wet film thickness decreases from 800 ㎛ to 200 ㎛.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.5 no.3
• /
• pp.23-28
• /
• 2006

The focus of this study is placed on the enhancement of flatness for the shielded slot plate, one of main components of the MCFC stack. The shielded slot plate is to get curvature during manufacturing process since it is produced by forming operation from only one side of it. Therefore, a correction die is proposed to place just after the main die to apply unbending on the curved plate to get almost flat product. In the design for the correction die, four kinds of design factors are selected to study which factor is the most influencing one affecting the flatness of the plate. From the experimental results using Taguchi method, it has been revealed that the Young's modulus of urethane die is the most critical factor.

• Transactions of Materials Processing
• /
• v.18 no.2
• /
• pp.156-159
• /
• 2009

Slot coating has been wide spread in photo-resist coating on the glass for liquid crystal display. Die in slot coater consists of manifold and land. Material comes in inlet of the die and flow into the manifold and then flow out through the land. The coating thickness variations along the die length depend upon inside of die design such as manifold and die land. However the coating thickness variations along the moving direction(coating direction) of the coater depend upon the operational conditions of coater as well as die lip design. The coating behaviors including atmospheric air have been investigated in this study. Die geometries considered in this study were nozzle gap and length of the die lip. Coating gap and coating speed were the variables fur coating operational conditions. When the nozzle gap and length of die lip increased climbing effect of PR on the downstream die lip was reduced. Subsequently uniformity of coating thickness improved. Uniformity of coating thickness also enhanced as coating gap and coater speed increased. The uniformity of coating gap was related to the velocity vector distributions on the coating surface.

• Elastomers and Composites
• /
• v.48 no.4
• /
• pp.282-287
• /
• 2013

Slot coating has been widely spread in photo resist coating on glass for flat display monitor. High quality of coating is required as high quality of image in display is needed. Coating quality in the slot coating is divided into nozzle direction quality and machine direction quality. Nozzle direction quality is related to flow uniformity inside the die whereas machine direction quality is related to die lip design and operational conditions. In this study coating uniformity in the machine direction of slot coating has been investigated through computer simulation. Die lip angle and die lip length were considered as outside die geometry and coating speed was considered as operational condition. Coating behavior has been analyzed and coating quality has been evaluated through computer simulation. Coating thickness decreased and coating uniformity increased as coating speed increased. However, the stability of meniscus formation was reduced and subsequently coating stability was reduced as coating speed increased. Coating thickness deviation decreased as die lip angle increased in down stream die. Coating thickness decreased and time to reaching steady state increased as increased die lip length in down stream die.

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.2
• /
• pp.159-166
• /
• 2015

Slot-die coating is well known technique to guarantee a uniformly coated layer and is compatible with roll-to-roll process. In actual roll-to-roll slot-die coating process, the lateral difference of coated layer thickness is observed. An experimental study was performed to improve the coating quality. Coating speed and coating gap were selected as the experimental factors. A full factorial, statistical method was conducted to optimize the process conditions. Based on the results of repeated experiment, the lowest deviation of lateral thickness (700 nm, <10%) was achieved at 10 m/min coating speed and $300{\mu}m$ coating gap. This result has significance because such optimized process guideline can be utilized with all process improvement in various coating applications.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.8
• /
• pp.611-616
• /
• 2016

Computational fluid dynamic simulation based on the ABAQUS software was conducted to observe the inside flow of slot-die nozzle. The slot-die nozzle was modeled as 3-dimensional structure and three significant parameters were determined: inlet velocity of fluid, reservoir angles, number of strips none of which have been mentioned previously in the literature. The design of experiment, full factorial analysis was performed within determined design and process levels. The simulation result shows the inlet fluid velocity is most significant factor for the flows of inside nozzle. As an interaction effect, reservoir angle is closely related with number of strip that should address when the nozzle is designed. Moreover, the optimized values of each determined parameter were obtained as 35 mm/s of inlet velocity, 3 of strip numbers, and $22^{\circ}$ of reservoir angles. Based on these parameters, the outlet velocity was obtained as 0.53% of outlet uniformity which is improved from 8.67% of nominal results.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.10
• /
• pp.115-120
• /
• 2018

This study examined the cast quality of small-sized induction motor rotors during the die casting process. Numerical analyses with 3-dimensional half models were performed to investigate the filling patterns of aluminum molten metals into a mold after high-speed injections. The following were obtained from numerical analyses and experimental results. First, molten metals started to fill the lower end ring, then moved horizontally to fill the core slot and upper end ring, and finally stopped to fill the rotor core slot. Second, circulation of molten metals occurred at the lower end ring, resulting considerable porosity at the section of lower end ring from the experimental results. Third, further work for obtaining sound quality of rotor core cast is required to develop a new shape of the rotor core cast or improve the die casting conditions.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.4
• /
• pp.106-113
• /
• 2000

One of the recent changes in machining technology is rapid application of micro- and high precision grinding processes. A fine groove generation is necessary for the fabrication of optics, electronics and semiconductor parts. Slot grinding is very efficient for the generation of micro ordered groove with hard and brittle materials. In the process of slot grinding, chipping at the sharp edges and microcracks of the ground grooves are inevitable defects. Chipping should be reduced for the improvement of surface integrity. Mechanical contact with diamond grits causes microcracks at the grooves. This damage resides subsurface, and can be the cause of failure of the punch die. This paper deals with chipping generation at the sharp edges, surface integrity of side groove and fracture strength is related to the microcracks in the slot grinding.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.6
• /
• pp.491-495
• /
• 2014

We developed a compact high-precision slot-die coating machine for thin-film deposition on a flexible substrate. For smooth and precise coating, air-bearing and linear motor system were employed to minimize velocity ripple. The gap control mechanism is specially designed to have repeatability of gap between nozzle and substrate under 1 ${\mu}m$. Due to extremely precise gap control, the machine can coat thin-films down to 50 nm with $200mm{\times}100mm$ size. A thin film of Ag nano-particle ink is coated for demonstration.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.273-276
• /
• 2006

The focus of this study is on the enhancement of flatness for the shielded slot plate, one of main components of the MCFC stack. The shielded slot plate is to get curvature during manufacturing process since it is produced by forming operation from only one side of it. Therefore, a correction die is proposed to place just after the main die to apply unbending on the curved plate to get almost flat product. In the design for the correction die, four kinds of design factors are selected to study which factor is the most influencing one affecting the flatness of the plate. From the experimental results using Taguchi method, it has been revealed that the Young's modulus of urethane die is the most critical factor.