• Geotechnical Engineering
• /
• v.12 no.6
• /
• pp.37-50
• /
• 1996

In this study, we collected data through the investigation of rock slopes of highway. By analyzing the collected data, the main factors of rock slope failure were studied. We studied on the failure types and scales according to rock types and geological structures in many rock slopes of highway. As a result, it was shown that many failed slopes were distributed in the areas of Cretaceous sedimentary rocks of south-eastern part in the Korean Peninsula and the Gneiss Complex in both Kyonggi-Do and Kangwon-Do. According to rock types, the following slope failure types were shown : that igneous rocks had the types of rock fall, plane failure, soil erosion and circular failure but had low failure frequency, and sedimentary rocks had predominantly the type of plane failure. Metamorphic rock showed the types of circular failure, wedge failure and plane failure due to poor rock qualities . According to geological structures, the following slope failure types were shown slope failure in igneous rocks was caused by joints, and in sedimentary rocks by bedding plane, and in metamorphic rocks by faults and poor rock qualities.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.635-642
• /
• 2004

Failure occurred slope, due to typhoon 'Rusa' and 'Maemi' last two years, was studied to evaluate the slope failure characteristics. There're three types of the slope in this study, ie. soil slope, rock slope, mixed slope. Statistical analysis was used to estimate the relation between slope type and failure mode. Among the failure occurred slope, soil slope & mixed slope are dominant at the ratio of 33%, 44% respectively. We conclude that soil slope & mixed slope have more higher risk than rock slope during heavy rainfall.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.5
• /
• pp.83-91
• /
• 2006

Recently, the intensive rainstorm possibly induced by global warming plays a key role on the instability of railway adjacent slopes. The instability of slopes results as covering and loss of railway lines induced by slided soil mass. According to the site investigation on the failed slopes triggered by rainfall, low types of slope failure were observed: shallow, intermediate, gully erosion, and soil-rock interface failures. The observation reveals the different characteristics of slope failure depending on the thickness of soil layer, morphological features of slope, etc. Based upon the observations, flume tests were conducted to analyze the sliding mechanism of each failure. The variables of flume test are soil layer thickness, rainfall intensity, and morphology of slope under the constant condition of the percentage of fine, initial soil moisture content, slope angle and compaction energy. Test results show that shallow failure was mostly observed from the surface of the slope and caused by the soil erosion; in addition, compared to the other types of failure, the occurrence of initial erosion is late, however, the development of erosion is fast. In gully erosion failure, the collected water from the water catchment area helps erosion of the upper soil layer and transfer of residual corestone, which impedes the erosion process once the upper soil layers are eroded and corestone are exposed. The soil-rock interface failure shows the most fast initial erosion process among the failure types. Interestingly, the common feature observed from the different types of failure was the occurrence of the initial deformation near the toe of slopes which implies the existence of surbsurface flow along the downslope direction.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.11b
• /
• pp.103-114
• /
• 2002

Stability of cut-slope is considered to have a deep relationship with rock types since rock has its own engineering and geological characteristic such as shear strength, durability, weathering profile, geological structures. Therefore, analysis of geological and engineering characterisics of rock mass is essential for the evaluation of rock slope stability This paper introduces the statistical data of slope failure cases which was collected from highway slopes constructed in sedimentary rock mainly of shale in Ky ng-sang Basin. Primary failure feature in this area is planar failure along the bedding regardless of slope geometry. Even a disasterous slope failure case due to the thick clay layer between the beddings was reported. Failures and rock fall were reported to ocurred frequently after the completion of cutting due to the weathering, so long-term slope stability should be considered as a important factors in design.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.10a
• /
• pp.3.1-14
• /
• 2002

Many human lives and properties have been damaged by the annually occurring natural disasters. Among them, a typhoon accompanying a gale and a localized torrential downpour induce a first order damages. In this study, states, scales and other characteristics of slope failure induced by the typhoon Rusa, which damaged the whole Korea peninsular on August 30th for 3 days, were analyzed. In addition, permanent measures for slope failure are conducted to prepare natural disasters. Since the key factor on the slope failure is considered to be a rainfall. The characteristics of domestic rainfall and typhoon are investigated, and then failure forms and some characteristics of slope failure are analyzed. By comparing with the data of existing slopes, the hazard of slope failure is examined. There fundamental results could be applied to the future measures of slope failure.

• Journal of Forest and Environmental Science
• /
• v.30 no.1
• /
• pp.71-75
• /
• 2014

Forest roads failure is one of the most common problems caused by heavy rainfalls. This study investigated the characteristics on stabilization measures installed for cutting slopes failure of forest road resulted from heavy rainfalls. Three primary factors (slope length, slope gradient, soil type) affecting cutting slope failure were considered and stabilization measures were classified into two types (A type: wooden fence, vegetation sandbag, stone masonry; B type: wire cylinder, gabion, concrete retaining wall) through discriminant analysis based on their capacity of resistance to slope failure. Results showed that A type was mainly installed in such conditions as cut slope <8 m, cut slope gradient $30-40^{\circ}$ and soil type with soil while B type occurred in locational conditions as cut slope length >8 m, cut slope gradient < $30^{\circ}$ and > $30^{\circ}$, and soil type of gravelly soil and rock.

• The Journal of Engineering Geology
• /
• v.27 no.3
• /
• pp.267-274
• /
• 2017

Behavior of rock mass depend on the mechanical properties of intact rock and geometrical property of discontinuity distributed in rock mass. In case of rock slope, particularly, location of slope failure surface and behavior after failure are changed due to discontinuities. In this study, two 3D slope stability analysis methods were developed for two different failure types which are circular failure and planar failure, considering that failure type of rock slope is dependent on scale of discontinuity which was then applied to real rock slope to review the applicability. In case of circular failure, stable condition was maintained in natural dry condition, which however became unstable when the moisture content of the surface was increased by rainfall. In case of planar failure, rock slope become more unstable comparing to dry condition which is attributable to decrease in friction angle of discontinuity surface due to rainfall. Viewing analysis result above, analysis method proved to have well incorporated the phenomenon occurred on real slope from the analysis result, demonstrating its applicability to reviewing the slope stability as well as to maintaining the slope.

• Geomechanics and Engineering
• /
• v.16 no.6
• /
• pp.655-667
• /
• 2018

To evaluate the stability of a rock slope with one pre-exiting vertical crack, this paper performs corresponding probabilistic stability analysis. The existence of cracks is generally ignored in traditional deterministic stability analysis. However, they are widely found in either cohesive soil or rock slopes. The influence of one pre-exiting vertical crack on a rock slope is considered in this study. The safety factor, which is usually adopted to quantity the stability of slopes, is derived through the deterministic computation based on the strength reduction technique. The generalized Hoek-Brown (HB) failure criterion is adopted to characterize the failure of rock masses. Considering high nonlinearity of the limit state function as using nonlinear HB criterion, the multivariate adaptive regression splines (MARS) is used to accurately approximate the implicit limit state function of a rock slope. Then the MARS is integrated with Monte Carlo simulation to implement reliability analysis, and the influences of distribution types, level of uncertainty, and constants on the probability density functions and failure probability are discussed. It is found that distribution types of random variables have little influence on reliability results. The reliability results are affected by a combination of the uncertainty level and the constants. Finally, a reliability-based design figure is provided to evaluate the safety factor of a slope required for a target failure probability.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.4 no.3 s.14
• /
• pp.9-17
• /
• 2004

In recent years slope failure due to heavy rainfalls or local downpours usually accompanied by typhoons has increasingly occurred in Korea. Also, the damages caused by slope failure have a tendency to be more disastrous than before. This study has been conducted to prepare an early warning system for slope failure by : (1) analyzing types and causes of slope failure, (2) examining the published evaluation criteria for slope stability, (3) estimating slope stability by considering the properties of slope-forming materials as well as the topographical and geological properties of slopes, and (4) determining the most important variables of affecting the stability of the slope under consideration. The data on the variations of slope conditions measured by an automatic in-situ measurement system and then transmitted to the central analysis system by using an internet. The most important variables can be back-calculated in the central system and compared with the values for the first and second management criteria. These management criteria should be modified and corrected continuously in the future by accumulated data and knowledge related to the early warning system for slope failure.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.03a
• /
• pp.339-346
• /
• 1999

The stability of rock slope is considered to have a deep relation with types of rocks because types of rocks have their own typical weathering profiles, geological structures and characteristics of failures. Therefore it is essential for the evaluation of rock slope stability to analyze geological and engineering characteristics in rock mass. The data which collected from investigated slopes in sedimentary rock of Kyengsang Basin along highways were analyzed. Primary factors affecting slope stability in rock mass are: dips and strikes of slopes and discontinuities, shear strength of discontinuities, slope geometry and geological structures etc.