• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 F
• /
• pp.1984-1986
• /
• 1998

This paper presents an optimal efficiency control for the inverter fed induction machine system using neural network. The motor speed and the load torque vary the efficiency characteristics of an induction motor. The optimal slip frequency has nonlinearity varied by the load torque as well as the motor speed. The induction motor is driven using the inverter system and the indirect vector control method which input is slip frequency. The neural network for estimating the optimal slip frequency has two input layer(the motor speed and the load torque) and one output layer(the optimal slip frequency that minimize the input power). Learning algorithm of the neural network is the back-propagation. Using the equivalent circuit including the nonlinearity of the induction motor, the loss reduction is analyzed quantitatively. Experimental results are shown noticeable power savings by proposed scheme in high speed and light load conditions.

• 한국터널지하공간학회 논문집
• /
• 제21권6호
• /
• pp.811-823
• /
• 2019

최근에는 수직구 구조물 시공방법으로 현장타설 공법 대비 시공속도가 빠르며, 안전하고 경제적인 연속상승 슬립폼 공법이 다수의 현장에 적용되고 있다. 슬립폼 공법으로 시공 가능한 높이는 2.5~4 m/day로 알려져 있는데, 콘크리트 온도가 10~30℃의 범위 밖에서는 강도 변화나 탄성 특성의 변화에 미치는 영향이 크므로 동절기 공사에서는 3 m/day 이상의 시공속도를 내기가 어렵다. 또한, 콘크리트는 수화 작용으로 인해 수화열이 발생하는데, 이는 콘크리트의 온도 균열을 초래한다. 따라서 슬립폼 연속상승시 콘크리트의 온도 제어 양생이 필요하며, 본 연구에서는 히팅 패널 및 시험용 연속상승 장치를 개발하여 반발경도, 초음파 전파시간, 수화열 및 외부온도를 측정하였다. 이를 기반으로 히팅슬립폼을 제작하였으며, "김포 현장"과 "신월 현장"에 히팅슬립폼을 적용하였다. 김포현장은 주간(08:00~17:30) 평균 1.9 m/day 또는 0.200 m/hr, 신월 현장은 2.0 m/day 또는 0.210 m/hr를 목표 상승속도 값으로 비교하였다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2004년도 학술대회지
• /
• pp.215-220
• /
• 2004

Molecular Dynamics(MD) method was used to investigate the change of friction force due to interaction between dislocations and a grain boundary when a Ni tip was scratched on a Cu bicrystal. The substrate comprised a Cu bicrystal containing a vertical$\Sigma=5(210)$ grain boundary. The moving tip for scratching simulation was consisted of fixed Ni atoms emulating a rigid tip. The indentation depth was $3.6\AA$ and the scratching was performed along <110>direction in the first grain. As the scratching was continued, nucleation and propagation of dislocations were observed. In the early stage, the grain boundary played as a barrier to moving dislocations and interrupting further dislocation movement with no dislocation resulting in no propagation across the grain boundary. As the Ni tip approached the grain boundary, dislocations were nucleated at the grain boundary and propagated to the second grain. However, stick-slip phenomena that were observed on a single crystal scratching were not observed in the bicrystal. And, instead, irregular oscillation of friction force was observed during the scratching due to the presence of a grain boundary.

• 대한토목학회논문집
• /
• 제31권4A호
• /
• pp.295-302
• /
• 2011

초장대교 콘크리트 고주탑 시공시에 사용되고 있는 슬립폼 시스템의 상승속도를 결정하는 요소인 초기경화시간은 콘크리트가 거푸집에서 안전하게 빠져나올 수 있는 굳기를 갖게 되는 콘크리트 타설 후 경화시간으로서, 배합 시 단위시멘트량 및 타설시 여러 현장 환경에 크게 영향을 받으므로, 콘크리트 타설 전에 초기경화시간을 정확히 파악하는 것은 매우 어렵다. 따라서 슬립폼 시스템의 안전성 확보 및 콘크리트면의 유지관리 문제가 발생하지 않도록 초기경화시간 결정을 위한 콘크리트 경화정도를 파악하는 기술이 필요하다. 더구나 슬립폼 공법은 연속적인 시공이 이루어지므로 거푸집 탈형 전 콘크리트의 경화정도를 연속적으로 파악할 수 있어야 한다. 초음파를 이용한 기법은 콘크리트면에 초음파를 투과시켜 투과된 신호를 측정 및 분석하는 방법으로 정량적이며 연속적으로 콘크리트의 경화정도를 파악할 수 있다. 특히 표면파 속도를 이용하는 기법은 표면을 따라 전파하는 표면파의 특성을 이용한 것으로서 표면파 속도의 변화를 통해 콘크리트 경화정도를 알 수 있으며, 주탑과 같이 두께가 두꺼운 콘크리트 구조물에 적용이 적합하다. 따라서 본 논문에서는 표면파 속도를 이용하여 콘크리트의 경화정도를 추정함으로서 슬립폼 시스템의 상승속도를 결정하는 연구를 수행하였다. 먼저 슬립폼 시스템 상승속도와 초기경화시간과의 관계식을 유도하였으며, 표면파 진행문제의 수치해석 결과를 연속웨이블릿변환 하여 표면파 속도를 추정하였다. 이때 탄성파 발생위치와 두 개의 수신점 거리에 따른 추정된 표면파 속도의 정밀도를 조사하였으며, 추정된 표면파 속도와 탄성계수와의 관계를 조사하였다.

• 대한토목학회논문집
• /
• 제32권5D호
• /
• pp.483-492
• /
• 2012

슬립폼 공법에 있어서 초기경화시간은 콘크리트가 거푸집에서 안전하게 빠져나올 수 있는 굳기를 갖게 되는 콘크리트 타설 후 경화시간으로써 슬립폼 시스템의 상승속도를 결정하는 중요한 요소이다. 따라서 슬립폼 시스템의 안전성 확보와 콘크리트의 시공품질을 확보하도록 초기경화시간을 파악하는 기술이 필요하다. 본 논문에서는 초음파를 이용하는 기법 중 표면파 속도를 이용하여 콘크리트의 경화정도를 파악하여 초기경화시간을 추정함으로써 슬립폼 시스템의 상승 시기를 결정하는 연구를 수행하였다. 관입저항시험과 압축강도시험을 수행하여 콘크리트의 초기경화시간과 압축강도와의 관계를 규명하였고, 또한 압축강도와 표면파 속도와의 관계를 규명하기 위해 초음파시험을 동시에 수행하였다. 표면파 속도를 측정하기 위해 연속웨이블릿변환을 사용하였으며, 이때 수치해석을 통해 연속웨이블릿변환의 사용에 대한 타당성을 입증하였다. 이로부터 슬립폼 시스템의 상승에 요구되는 표면파 전파속도를 제안하였으며, 슬립폼 시스템의 축소모형실험을 수행하여 제안한 표면파 속도가 슬립폼 상승 시기를 결정하는데 사용될 수 있음을 입증하였다.

• Structural Engineering and Mechanics
• /
• 제46권6호
• /
• pp.827-842
• /
• 2013

In this paper, the wave propagation in generalized thermo elastic plate immersed in fluid is studied based on the Lord-Shulman (LS) and Green-Lindsay (GL) generalized two dimensional theory of thermo elasticity. Two displacement potential functions are introduced to uncouple the equations of motion. The frequency equations that include the interaction between the plate and fluid are obtained by the perfect-slip boundary conditions using the Bessel function solutions. The numerical calculations are carried out for the material Zinc and the computed non-dimensional frequency, phase velocity and attenuation coefficient are plotted as the dispersion curves for the plate with thermally insulated and isothermal boundaries. The wave characteristics are found to be more stable and realistic in the presence of thermal relaxation times and the fluid interaction.

• 한국해양공학회지
• /
• 제5권2호
• /
• pp.198-198
• /
• 1991

Not only difference of fatigue crack growth and propagation behavior resulted from the grain size, the hardness ratio and volume fraction in M.E.F. dual phase steel composed of martensite in hard phase and ferrite in soft phase, but also the effects of the plastic constraint were investigated by fracture mechanics and microstructural method. The main results obtained are as follows: 1) The fatigue endurance of M.E.F. steel increases with decreasing the grain size, increasing the ratio of hardness and volume fraction. 2) The initiation of slip and crack occures faster as the stress level goes higher. These phenomena result from the plastic constraint effect of the second phase. 3) The crack propagation rate in the constant stress level is faster as the grain size gets larger, the ratio of hardness lower and volume fraction smaller.

• 대한조선학회지
• /
• 제12권2호
• /
• pp.43-58
• /
• 1975

There are many reports on fatigue crack of metallic materials but most of them relate crack propagation rate to stress intensity factor. The problem of crack propagation is not yet clarified, especially the bridge between micro and macro phenomena In this experiment rotating bending fatigue tests have been carried out with smoothed specimen of rolled steel plates including 0.2% carbon under application of three stress conditions to investigate the slip band and the crack propagation behaviour. The results obtained are as follows; 1) The length of cracks which have grown at initial crack tips can be expressed as follows; $l=Ae^{BNr}$(A,B: constant, $N_r$: cycle ratio) $\frac{dl}{dN}=\frac{AB}{N_f}{\cdot}e^{BNr}$($N_f$:fatigue life) 2) The ratio of slipped grain number to total grain number is $S_f=7{\sigma}-5.6$-5.6{\sigma}_c$($\sigma$: stress amplitude) (${\sigma}_c$: fatigue limit) 3) When the fatigue process transfers from Stage I to Stage II, the crack which propagates into specimen changes its direction from that of the maximum shear stress to the direction of perpendicular to principal stress and this is same in the circumferential direction of specimen. the crack propagation behaviors of both sides of a crack are different each other when they approach to the grain boundary.

• 대한기계학회논문집A
• /
• 제26권12호
• /
• pp.2581-2589
• /
• 2002

In this research, fretting tests were conducted in air to investigate the wear characteristics of fuel cladding materials with the fretting parameters such as normal load, slip amplitude, frequency and the number of cycles. A high frequency fretting wear tester was designed for this experiment by KAERI. After the experiments, the wear volume and the shape of wear contour were measured by the surface roughness tester. Tribologically transformed structures(TTS) were analysed by means of optical and scanning electron microscopes to identify the main wear mechanisms. The results of this study showed that the wear volume were increased with increasing slip amplitude, and the shape of wear contour was transformed V-type to W-type. Also, it was found that the critical slip amplitude was 168${\mu}{\textrm}{m}$. These phenomena mean that wear mechanism transformed partial slip to gross slip to accelerate wear volume. The wear depth increased with an increase of friction coefficient due to increase of normal load and frequency. The fretting wear mechanisms were believed that, after adhesion and surface plastic deformation occurred by relative sliding motion on the contact between two specimens, TTS creation was induced by surface strain hardening and wear debris were detached from the contact surface which were produced by the micro crack propagation and creation.

• Corrosion Science and Technology
• /
• 제6권4호
• /
• pp.170-176
• /
• 2007

Iodine-induced stress corrosion cracking (ISCC) properties and the associated ISCC process of Zircaloy-4 and an Nb-containing advanced nuclear fuel cladding were evaluated. An internal pressurization test with a pre-cracked specimen was performed with a stress-relieved (SR) or recrystallized (RX) microstructure at $350^{\circ}C$, in an iodine environment. The results showed that the $K_{ISCC}$ of the SR and RX Zircaloy-4 claddings were 3.3 and 4.8MPa\;m^{0.5}, respectively. And the crack propagation rate of the RX Zircaloy-4 was 10 times lower than that of the SR one. The chemical effect of iodine on the crack propagation rate was very high, which was increased $10^4$ times by iodine addition. Main factor affecting on the micro-crack nucleation was a pitting formation and its agglomeration along the grain boundary. However, this pitting formation on the grain-boundary was suppressed in the case of an Nb addition, which resulted in an increase of the ISCC resistance when compared to Zircaloy-4. Crack initiation and propagation mechanisms of fuel claddings were proposed by a grain boundary pitting model and a pitting assisted slip cleavage model and they showed reasonable results.