• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.17 no.6
• /
• pp.245-250
• /
• 2007

This study was focused on the effect of sintering additive and particle size on the low temperature sintering of $0.85CaWO_4-0.15SmNbO_4$ ceramics. With an increase of $CaV_2O_6$ content, the sintering temperature of the specimens was reduced from $1150^{\circ}C\;to\;800^{\circ}C$. The dielectric constant (K) and Qf value were increased with $CaV_2O_6$ content. These results are due to the enhancement of the density by the liquid phase sintering. Temperature coefficient of resonant frequency (TCF) was slightly shifted to the positive value with $CaV_2O_6$ content. Typically, K of 12.64, Qf of 23,106 GHz, TCF of $-34ppm/^{\circ}C$ were obtained for the specimens with 7 wt.% $CaV_2O_6$ sintered at $900^{\circ}C$ for 3 h.

• Journal of the Korean Ceramic Society
• /
• v.55 no.6
• /
• pp.576-580
• /
• 2018

In this study, a small amount of CoO was added to commercial Gd-doped $CeO_2$ (GDC) powder. The CoO addition greatly enhanced sinterability at low temperatures, i.e., more than 98% of relative density was achieved at $1,000^{\circ}C$. When GDC/8YSZ (8 mol% yttrium stabilized zirconia) bilayers were sintered, Co-doped GDC showed excellent adhesion to the YSZ electrolyte. Transmission electron microscope (TEM) analysis showed that there were no traces of liquid films at the grain boundaries of GDC, whereas liquid films were observed in the Co-doped GDC sample. Because liquid films facilitate particle rearrangement and migration during sintering, mechanical stresses at the interface of a bilayer, which are developed based on different densification rates between the layers, might be reduced. In spite of $Co^{2+}$ doping in GDC, the electrical conductivity was not significantly changed, relative to GDC.

• Applied Chemistry for Engineering
• /
• v.8 no.5
• /
• pp.811-815
• /
• 1997

The present work describes the effect of dry grinding of a mixture composed of $Y_2O_3$, $BaCO_3$ and CuO powders with a planetary ball mill before heat treatment on crystal structure and superconductivity in the $YBa_2Cu_3O_{7-y}$. The specific surface area of the ground product of mixture decreased with an increase in the grinding time, after showing an upward trend up to 60 minutes of grinding. The critical current density, which was influenced by the grinding time of mixture, indicates the maximum value of about $150A/cm^2$ in the case of 60 minutes grinding, while the critical temperature, which were around 90K, for the sintered bodies were almost independent of the grinding time.

• Journal of the Korean Ceramic Society
• /
• v.46 no.1
• /
• pp.81-85
• /
• 2009

$B_4C$ ceramics were fabricated by a hot-press sintering method and their sintering behavior, microstructure and mechanical properties were evaluated. Relative density of $B_4C$ ceramics were obtained by a hot-press sintering method reached as high as 99% without any sintering additives. The mechanical properties of $B_4C$ ceramics was improved by a methanol washing process which can remove $B_2O_3$ phase from a $B_4C$ powder surface. This improvement results from the formation of homogeneous microstructure because the grain coarsening was suppressed by the elimination of $B_2O_3$ phase. Particularly, mechanical properties of the sintered specimen using a methanol washed powder improved compared with the specimen using an as-received commercial powder.

• Korean Journal of Materials Research
• /
• v.19 no.2
• /
• pp.55-60
• /
• 2009

In this study, Ti powder was fabricated from Ti scrap by a hydrogenation-dehydrogenation (HDH) method. The Ti powders were compacted by Spark plasma sintering (SPS) and the microstructure and mechanical properties of the powders were investigated. A hydrogenation reaction of Ti scrap occurred at temperatures near $450^{\circ}C$ with a sudden increase in the reaction temperature and a decrease in the pressure of the hydrogen gas as measured in a furnace during the hydrogenation process. In addition, a dehydrogenation process was carried out at $750^{\circ}C$ for 2hrs in a vacuum of $10^{-4}torr$. The Ti powder sizes obtained by hydrogenation-dehydrogenation and mechanical milling processes were in the range of $1{\sim}90{\mu}m$ and $1{\sim}100{\mu}m$, respectively. To fabricate Ti compacts, Ti powders were sintered under an applied uniaxial punch pressure of 40 MPa at in a range of $900{\sim}1200^{\circ}C$ for 5 min. The relative density of a SPSed compact was 99.6% at $1100^{\circ}C$, and the tensile strength decreased with an increase in the sintering temperature. However, the hardness increased as the sintering temperature increased.

• Transactions on Electrical and Electronic Materials
• /
• v.10 no.4
• /
• pp.121-124
• /
• 2009

In this study, in order to develop compositions of ceramics suitable for piezoelectric actuator and ultrasonic vibrator applications using low temperature sintering, multilayer, PMN-PNN-PZT ceramics were fabricated using $Li_2CO_3$ and $Na_2CO_3$ as sintering aids. Their structural, piezoelectric and dielectric characteristics were investigated according to the Zr/Ti ratio. As the Zr/Ti ratio increased, the electromechanical coupling factor $k_p$, and piezoelectric constant $d_{33}$ and the mechanical quality factor $Q_m$ all increased with Zr/Ti ratio and then decreased after the ratio exceeded 50/50. At the ratio of Zr/Ti =49/51 and sintering temperature of $900^{\circ}C$; the density, electromechanical coupling factor $k_p$, dielectric constant ${\varepsilon}_r$ piezoelectric $d_{33}$ constant and mechanical quality factor $Q_m$ all showed the optimum values of 7.900 $g/cm^3$, 0.576, 856, 312 pC/N, 1,326, respectively. These property values are very suitable for multilayer ceramics actuator applications.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.9
• /
• pp.766-770
• /
• 2007

In this study, in order to develop low temperature sintering ceramics for multilayer piezoelectric actuator, $0.07Pb(Mn_{1/3}Nb_{2/3})O_3-xPb(Ni_{1/3}Nb_{2/3})O_3-(0.93-x)Pb(Zr,Ti)O_3$ ceramics system were fabricated using $Li_2CO_3-Bi_2O_3-CuO$ sintering aids and the specimens were sintered at $930^{\circ}C$. Thereafter, their piezoelectric and dielectric characteristics were investigated according to the amount of PNN substitution. At 9 mol% PNN substitution, density, electromechanical coupling factor ($k_p$), dielectric constant, mechanical quality factor ($Q_m$) and piezoelectric constant ($d_{33}$) showed the optimum value of $7.86g/cm^3$, 0.60, 1640, 1323 and 387 pC/N, respectively. It is considered that these values are suitable for piezoelectric divece application such ad multilayer piezoelectric actuator and ultrasonic vibrator with pure Ag internal electrode.

• Journal of the Korean Ceramic Society
• /
• v.42 no.6 s.277
• /
• pp.411-416
• /
• 2005

Y-TZP(Yttria-stabilized Tetragonal Zirconia Polycrystal) ceramics are of great interest as engineering and structural materials due to their excellent mechanical properties arising from transformation toughening, it is also reported that the 3Y-TZP($3 mol\%$ Yttria-stabilized Tetragonal Zirconia Polycrystal) has the best mechanical properties in Y-TZP ceramics. But to use widely for engineering and structural materials, it remains an important challenge to be able to improve its fracture toughness. In order to produce the 3Y- TZP ceramics showing much better mechanical properties, milling method adding monoclinic zirconia to 3Y-TZP was adopted and the resultant mechanical properties containing apparent density and fracture toughness were measured by using proper techniques. Experimental results showed that the 3Y-TZP specimen containing $33 wt\%$ of monoclinic zirconia, which was sintered at $1450^{\circ}C$, has the highest fracture toughness value of $11.38 MPa{\cdot}m^{1/2}$ which is three times higher than that of normal 3Y-TZP ceramics.

• Journal of the Korean Ceramic Society
• /
• v.41 no.12 s.271
• /
• pp.884-888
• /
• 2004

Effects of NiO were studied in aspects of dielectric properties and microstructure of $0.96(0.91Pb(Mg_{1/3}Nb_{2/3})O_3-0.09PbTiO_3)­0.04BaTiO_3$ (PMN-PT-BT, PBT). The PBT was prepared by a conventional mixed oxide method using $(MgCO_3)_4{\cdot}Mg(OH)_2$ instead of MgO through Lewis acid-base interaction. NiO was added in the range of 0.5 to $3.0\;wt\%$ as thermally decomposable $2NiCO_3{\cdot}3Ni(OH)_2$ and it seemed to enhance densification to a large extent below $1000^{\circ}C$. But all the systems gave rise to ceramics with almost same relative sintered density of 96% by sintering at $1000^{\circ}C$ for 2 h. But it turned out that the addition of NiO was detrimental to dielectric constant but beneficial to the loss of dielectric constant.

• Journal of the Korean Ceramic Society
• /
• v.30 no.10
• /
• pp.829-837
• /
• 1993

Chemically and geometrically homogeneous mixing of Si3N4 powders with sintering additives(YAG, 3Y2O3$.$5Al2O3) was attempted via coprecipitation method. X-ray dot maps for the additive elements(Al and Y) showed that the additives are evenly distributed in the powder mixture prepared by coprecipitation method(CP). TEM observation of the coprecipittion-treated Si3N4 powders revealed that they are covered with extremely fine crystallites of additive. The shift in isoelectric point(IEP) of Si3N4 powders from pH 6.7 to pH 7.9 after coprecipitation mixing gave another evidence for coating of Si3N4 powders with YAG additives. SIMS analysis for composition on the surface and in the matrix of mixed powders showed that the YAG additives are highly enriched on the surface of coprecipitation-treated Si3N4 powders. Especially when a small amount of additive was used, the effect of homogeneous additive distribution on densification was preceptible: After pressureless-sintering of powder compacts containing 5 mol% YAG at 1800$^{\circ}C$ for 0.5h, a sintered density of 96.5% theoretical was obtained from the specimens prepared bycoprecipitation in comparison with 93.8% from the mechanically-mixed one.