• Journal of Mechanical Science and Technology
• /
• 제15권2호
• /
• pp.152-159
• /
• 2001

In this paper it is intended to set-up a sound model of the 60,000rpm 100kW prototype APU gas turbine rotor-bearing system, and particularly to investigate the influences of the tie shaft on the rotordynamic characteristics of the entire APU gas turbine rotor-bearing system, employing the dual shaft model. Firstly, a mock-up APU rotor has been constructed to test and verify the model. Analytical natural frequency results have agreed with the corresponding modal test ones to within 5% difference. Then, the rotordynamic characteristics of the prototype APU rotorbearing system have been investigated. Natural vibration and unbalance response analyses results have shown that the inner tie shaft resonance can cause high enough vibration of the outer main rotor shaft. This could be a concern as the rotor journals operate on very thin air film at high speed. It is concluded as a conservative design practice that the inner tie shaft should be explicitly modeled in the rotordynamic analysis of the APU rotor-bearing system.

• 소음진동
• /
• 제10권4호
• /
• pp.623-628
• /
• 2000

This paper presents the automatic plumbness measuring system form improving the accuracy and working time for plumbness measuring of semi-umbrella type hydraulic turbine generator. It is general practice that rotating shaft should run within acceptable vibration limit. In order to obtain more accurate measuring data for single stage shaft on the semi-umbrella type, plumbness approach must be established carefully and accurately. Generally, present plumbness procedure is required several calculation algorithm, laser sensor and data acquisition devices. As a result of application to actual new system it is confirmed that working time could be saved over 80% and accurate measurement data could be acquired.

• Smart Structures and Systems
• /
• 제30권2호
• /
• pp.209-219
• /
• 2022

The determination for bearing capacity of precast nodular piles is conventionally time-consuming and high-cost by using numerous experiments and empirical methods. This study proposes an intelligent method to evaluate the bearing capacity and shaft resistance of the nodular piles with high efficiency based on long short-term memory (LSTM) approach. A series of field tests are first designed to measure the axial force, shaft resistance and displacement of the combined nodular piles under different loadings, in comparison with the single pre-stressed high-strength concrete piles. The test results confirm that the combined nodular piles could provide larger ultimate bearing capacity (more than 100%) than the single pre-stressed high-strength concrete piles. Both the LSTM-based method and empirical methods are used to calculate the shift resistance of the combined nodular piles. The results show that the LSTM-based method has a high-precision estimation on shaft resistance, not only for the ultimate load but also for the working load.

• 지질공학
• /
• 제18권4호
• /
• pp.493-499
• /
• 2008

본 연구에서는 수평하중을 받는 화강편마암에 근입된 대구경현장타설말뚝에 대하여 수평방향의 거동특성을 분석하기 위하여 시험말뚝인 단일대구경현장타설말뚝 내부에 경사계를 설치하여 단계별 수평하중이 대한 심도별 변위량을 측정하였다. 실측치와 기존 이론식에 의한 계산치를 비교 분석하여 수평변위 거동특성을 평가하였다. 따라서, 단계별 재하하중에 따른 수평변위량의 계측값과 비교한 결과 전체적으로 Chang의 산정식과 유사한 결과를 나타내고 있으나 약간 과소평가 되는 경향이 있다. 그리나 유한차분법(FDM)과 p-y곡선법은 상부구간에서 과대평가 되는 경향을 나타내었다.

• Tribology and Lubricants
• /
• 제33권4호
• /
• pp.168-186
• /
• 2017

This paper presents a wear analysis procedure for calculating the wear of journal bearings during the start-up and coast-down cycles of a motoring stripped-down single cylinder engine operating with a tilted shaft. In order to decide whether the lubrication state of a journal bearing is in the mixed-elasto-hydrodynamic lubrication regime, we utilize lift-off speed and MOFT (most oil film thickness) under mixed-elasto-hydrodynamic lubrication regime at the corresponding aligned shaft. We formulate an equation for the modified film thickness in a misaligned journal bearing considering the additional wear volume described in Part I of this study. For this, we use the calculation results of the degree of misalignment and tilting angle obtained after finding the eccentricities of the two bearings supporting the crankshaft of a single cylinder engine. In this Part II, we calculate the wear of journal bearings using the fractional film defect coefficient, the asperity load sharing factor, and the modified specific wear rate for the application of mixed-elasto-hydrodynamic lubrication regime. We show that the accumulated wear volume after turning the ignition switch on and off once, increases to ${\sigma}=39{\mu}m$ and then decreases from ${\sigma}=39{\mu}m$ with increasing in surface roughness.

• 한국화재소방학회논문지
• /
• 제23권5호
• /
• pp.143-152
• /
• 2009

초고층건물의 수직통로에서 발생하는 연돌효과의 기체역학적 특성과 관련된 차압과 중성대의 위치 계산 및 연돌효과 발생의 가시화를 위하여 3가지 형태의 개구부를 갖는 단일 단순수직통로에 대하여 CFD 모델을 사용하여 수치해석을 하였다. 연돌효과의 차압은 이론식 계산 결과와 비교 시 수직통로의 높이가 높아질수록 차이가 커진다. 중성대 위치는 연돌효과 초기(t = 10s)에 Type A의 경우 수직통로의 높이가 30m 미만인, Type B의 경우 30m 이상인 모델에서 이론식 계산 결과와의 편차가 5% 미만으로 잘 일치한다. 따라서 수직통로 높이가 30m 이상인 다중개구부 수직통로(Type B)의 경우 CFD 모델을 사용하여 중성대 위치를 계산하는 것이 가능하다. 연돌효과의 가시화를 통하여 연돌효과의 공기 유동 현상을 쉽게 이해할 수 있다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1990년도 제11회 학술강연회초록집
• /
• pp.73-91
• /
• 1990

Incompressible turbulent flow in a single cavity of the stepped multi-cavity labyrinth seal is numerically analyzed to investigate an effect of the shaft speed on the leakage. SIMPLER algorithm is used to solve governing equations, and low-Reynolds k-$\varepsilon$ turbulence model as outlined by Launder and Sharma is adopted to predict turbulent flow. Pressure drops for the cavity with and without the groove are evaluated for four different Reynolds numbersand three different shaft speeds.

• Tribology and Lubricants
• /
• 제6권2호
• /
• pp.27-33
• /
• 1990

Incompressible turbulent flow in a single cavity of the stepped multi-cavity labyrinth seal is numerically analyzed to investigate an effect of the shaft speed on the leakage. SIMPLER algorithm is used to solve governing equations, and low-Reynolds k-$\varepsilon$ turbulence model as outlined by Launder and Sharma is adopted to predict turbulent flow. Pressure drops for the cavity with and without the groove are evaluated for four different Reynolds numbers and three different shaft speeds.

• 대한조선학회논문집
• /
• 제58권6호
• /
• pp.431-439
• /
• 2021

The Carbon Fiber Reinforced Plastic (CFRP) material is recently widely used in the composite industry with excellent rigidity and lightweight properties. A ship shaft system requires high standards of safety on torsional strength capacity. The purpose of this study is to verify the applicability of a CFRP shaft system to take the place of metal shaft systems for ships from a viewpoint of torsional strength. Selection of materials and manufacturing method are executed then two geometrically scaled CFRP shaft system models were designed and manufactured with three-layer patterns. The models were used for a series of torsion tests under single and repeated torsional loading conditions. Detailed design and manufacturing methods for a CFRP ship shaft system are documented and the torsion test results are listed in this paper. The results of this study could be useful guidelines on the development of CFRP ship shaft systems and a test method.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제11B권2호
• /
• pp.9-14
• /
• 2001

Because salient pole rotor type single phase SRM(Switched Reluctance Motor) has a simple structure and can be use both radial and axial direction magnetic flux at the same time, its output power per unit volume is high. Therefore, the shaft length can be minimized when compared with same output motors. However, salient pole rotor is hard to design due to its complex magnetic circuit. In this paper, salient pole rotor type single phase SRM with minimized shaft length is designed and selected the most suitable dimension of rotor, stator, pole arc and salient pole.