• Composites Research
• /
• v.35 no.3
• /
• pp.201-215
• /
• 2022

This paper presents the development of thin and lightweight ultra-high temperature radar-absorbing ceramic composites composed of an aluminosilicate ceramic matrix-based geopolymer reinforced ceramic fiber and sendust magnetic nanoparticles in X-band frequency range (8.2~12.4 GHz). The dielectric properties with regard to complex permittivity of ceramic/sendust-aluminosilicate composites were proportional to the size of sendust magnetic nanoparticle with high magnetic characteristic properties as flake shape and its concentrations in the target frequency range. The characteristic microstructures, element composition, phase identification, and thermal stability were examined by SEM, EDS, VSM and TGA, respectively. The fabricated total thicknesses of the proposed single slab ultra-high temperature radar absorber correspond to 1.585 mm, respectively, exhibiting their excellent EM absorption performance. The behavior of ultra-high temperature EM wave absorption properties was verified to the developed free-space measurement system linked with high temperature furnace for X-band from 25℃ to 1,000℃.

• The Journal of the Acoustical Society of Korea
• /
• v.41 no.5
• /
• pp.481-491
• /
• 2022

The active sonar transmission system consists of a transmitter that outputs an electrical signal and an underwater acoustic transducer that converts the amplified electrical signal into an acoustic signal. In general, the transmitter output characteristics are dependent on load impedance, and an underwater acoustic transducer, which is a transmitter load, has a characteristic that the electrical impedance varies largely according to frequency when driven. In such a variable impedance condition, the output of the active sonar transmission system may become unstable. Hence, this paper proposes a design and control technique of a sonar transmitter for transmitting a stable transmission signal even under variable impedance conditions of an underwater acoustic transducer in an active sonar transmission system. The electrical impedance characteristics of the underwater acoustic transducer are experimentally analyzed, and the sonar transmitter is composed of a single-phase full-bridge inverter, an LC filter, and a matching circuit. In this paper, the design and output control method of the sonar transmitter is proposed to protect the transmitter and transducer. It can secure stable output voltage characteristics even if it transmits the Linear Frequency Modulation (LFM) signal. The validity is verified through the simulation and the experiment.

• Advances in aircraft and spacecraft science
• /
• v.9 no.5
• /
• pp.415-431
• /
• 2022

Secondary flows have a huge impact on losses generation in modern low pressure gas turbines (LPTs). At design point, the interaction of the blade profile with the end-wall boundary layer is responsible for up to 40% of total losses. Therefore, predicting accurately the end-wall flow field in a LPT is extremely important in the industrial design phase. Since the inlet boundary layer profile is one of the factors which most affects the evolution of secondary flows, the first main objective of the present work is to investigate the impact of two different inlet conditions on the end-wall flow field of the T106A, a well known LPT cascade. The first condition, labeled in the paper as C1, is represented by uniform conditions at the inlet plane and the second, C2, by a flow characterized by a defined inlet boundary layer profile. The code used for the simulations is based on the Discontinuous Galerkin (DG) formulation and solves the Reynolds-averaged Navier-Stokes (RANS) equations coupled with the Spalart Allmaras turbulence model. Secondly, this work aims at estimating the influence of viscosity and turbulence on the T106A end-wall flow field. In order to do so, RANS results are compared with those obtained from an inviscid simulation with a prescribed inlet total pressure profile, which mimics a boundary layer. A comparison between C1 and C2 results highlights an influence of secondary flows on the flow field up to a significant distance from the end-wall. In particular, the C2 end-wall flow field appears to be characterized by greater over turning and under turning angles and higher total pressure losses. Furthermore, the C2 simulated flow field shows good agreement with experimental and numerical data available in literature. The C2 and inviscid Euler computed flow fields, although globally comparable, present evident differences. The cascade passage simulated with inviscid flow is mainly dominated by a single large and homogeneous vortex structure, less stretched in the spanwise direction and closer to the end-wall than vortical structures computed by compressible flow simulation. It is reasonable, then, asserting that for the chosen test case a great part of the secondary flows details is strongly dependent on viscous phenomena and turbulence.

• Korean Chemical Engineering Research
• /
• v.60 no.4
• /
• pp.620-629
• /
• 2022

By varying various experimental conditions such as heating rate, molar hourly space velocity (MHSV), and nitridation reaction temperature, vanadium oxynitride was prepared through temperature programmed reduction/nitridation reaction (TPRN) of vanadium pentoxide and ammonia, and characterization were performed. In order to investigate the physico-chemical properties of the prepared catalyst, N₂ adsorption-desorption analysis, X-ray diffraction analysis (XRD), hydrogen temperature programmed reduction (H₂-TPR), temperature programmed oxidation (TPO), ammonia temperature programmed desorption (NH₃-TPD), transmission electron microscopy (TEM) was performed. Transformation of V₂O₅ with 5 m² g^-1 low specific surface area by reduction at 340 ℃ to V₂O₃ showed a high specific surface area value of 115 m² g^-1 by micropore formation. As the nitridation temperature increased beyond that, the specific surface area continued to decrease due to sintering. The nitridation reaction variable that had the greatest influence on the specific surface area was the reaction temperature, and the x + y value of VN_xO_y of a single phase approached from 1.5 to 1.0 as the nitridation reaction temperature increased. At a high reaction temperature of 680 ℃, the cubic lattice constant a was VN. close to the value. At 680 ℃, the highest nitridation temperature among the experimental conditions, the ammonia conversion rate was 93%, and no deactivation was observed.

• Proceedings of the Korean Society of Embryo Transfer Conference
• /
• 2002.11a
• /
• pp.92-92
• /
• 2002

Considerable attention has been focused on the cryopreservation of semen and estrus induction in dog, as consequence of poor productivity caused by long anestrus period, in order to enhance the productivity of youngs and to preserve the breeds. The objectives of this study were to evaluate semen quality after cryopreservation and to evaluate the Pregnancy rate after insemination (AI). Fifty infertilie dogs (age 2∼3 years) were selected for the study and divided into three different estrus induction treatment groups. Group 1: dogs (n=15) were given clomifene (0.1 mg/kg) orally for five days at 12 hr intervals. Group 2: dogs (n=15) were given bromocriptine (50 $\mu\textrm{g}$/kg) orally for five days at 12 hr intervals, followed by single injection intravenously of 500 IU GnRH (Group 3, n=20) when pro-estrus occurred. The rates of pregnancy in estrus inducted dogs mated naturally compared to those inseminated artificially with ejaculated fresh semen and frozen-thawed semen. Estrus detection was performed using the method of vaginal smear and confirmed by the plasma progesterone assay. The ejaculated semen to freeze was exposed to a mixture of Tris extender with cryoprotectant (Trisma, 81 mM: TES, 209 mM: citric acid, 6 mM; glucose, 5 mM; glycerol, 8%) and cryopreserved gradually by slow-cooling at 17 cm above the surface of liquid nitrogen (LN$_2$) for 23 min. The motility of frozen-thawed spermatozoa was assessed by phase-contrast microscopy. To assess their viability and acrosome content, spermatozoa were stained with a vital stain and Fluorescence conjugated lectin Pisum Savitum Agglutinin (FITC/PAS), respectively. Pregnancy was confirmed by ultrasonograpy on day 25, 35 and 55 post insemination. The use of fresh semen, the pregnancy rates were observed 66.6, 66.6, 75.0 and 83.3% in natural estrus, clomifene induced, bromocriptine induced and a combination of GnRH and bromocriptine, respectively. The use of frozen-thawed semen, the pregnancy rates were observed 66.6, 33.3, 50.0 and 60.0% in natural estrus, clomifene induced, bromocriptine induced and a combination of GnRH and bromocriptine, respectively. No difference was observed in the number of offspring produced among natural estrus and treated groups inseminated with fresh or frozen-thawed semen. In conclusion, the pregnancy rate of dogs treated with a combination of GnRH and bromocriptine was more effective than use of clomifene or bromocriptine only. In addition, frozen-thawed semen can be used successfully far artificial insemination in dog.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.33 no.5
• /
• pp.167-173
• /
• 2023

Li₃V₂(PO₄)₃ and Li₃V₂(PO₄)₃/C composite with single phase monoclinic structure for the cathode materials are successfully synthesized by direct co-precipitation method using N₂H₄·H₂O as the reducing agent and alginic acid as the carbon source, and their electrochemical properties were compared. The particles with approximately 1~2 ㎛ size and the uniform spherical-like morphology of the narrow particle size distribution were obtained. In addition, the residual carbon can also improve the electrical conductivity. The Li₃V₂(PO₄)₃/C composite has improved initial specific discharge capacity and excellent cycle characteristics to maintain capacity stably than Li₃V₂(PO₄)₃. The results indicate that the reducing agent and carbon composite can affect the good crystallinity and electrochemical performance of the cathode materials.

• Composites Research
• /
• v.36 no.5
• /
• pp.289-296
• /
• 2023

In this study, we investigated the electromagnetic properties and microwave absorption characteristics of M-type hexagonal ferrites, which are known as millimeter-wave absorbing materials, according to their calcination temperature. The M-type ferrites synthesized using a molten salt-based sol-gel method exhibited a single-phase M-type crystal structure at calcination temperatures above 850℃. The synthesized particle size increased as well with the calcination temperature. Saturation magnetization increased gradually with increasing calcination temperature, but coercivity reached a maximum at 1050℃ and then rapidly decreased. After preparing a thermoplastic polyurethane (TPU) composite containing 70 wt% of M-type ferrites, we measured the complex permittivity and permeability in the Q-band (33-50 GHz) and V-band (50-75 GHz) frequency ranges, where ferromagnetic resonance occurred. Strong magnetic loss from ferromagnetic resonance occurred in the 50 GHz band for all composite samples. Based on the measured results, we calculated the reflection loss of the TPU/M-type ferrite composite. By calculating the reflection loss of the M-type ferrite composite, the M-type ferrite calcined at 1250℃ showed excellent electromagnetic wave absorption performance of more than -20 dB at 52 GHz with a thickness of about 0.5 mm.

• Korean Journal of Materials Research
• /
• v.34 no.4
• /
• pp.185-193
• /
• 2024

In this study, NASICON-type Li_1+XGa_XTi_2-X(PO₄)₃ (x = 0.1, 0.3 and 0.4) solid-state electrolytes for all-solid-state batteries were synthesized through the sol-gel method. In addition, the influence on the ion conductivity of solid-state electrolytes when partially substituted for Ti⁴⁺ (0.61Å) site to Ga³⁺ (0.62Å) of trivalent cations was investigated. The obtained precursor was heat treated at 450 ℃, and a single crystalline phase of Li_1+XGa_XTi_2-X(PO₄)₃ systems was obtained at a calcination temperature above 650 ℃. Additionally, the calcinated powders were pelletized and sintered at temperatures from 800 ℃ to 1,000 ℃ at 100 ℃ intervals. The synthesized powder and sintered bodies of Li_1+XGa_XTi_2-X(PO₄)₃ were characterized using TG-DTA, XRD, XPS and FE-SEM. The ionic conduction properties as solid-state electrolytes were investigated by AC impedance. As a result, Li_1+XGa_XTi_2-X(PO₄)₃ was successfully produced in all cases. However, a GaPO₄ impurity was formed due to the high sintering temperatures and high Ga content. The crystallinity of Li_1+XGa_XTi_2-X(PO₄)₃ increased with the sintering temperature as evidenced by FE-SEM observations, which demonstrated that the edges of the larger cube-shaped grains become sharper with increases in the sintering temperature. In samples with high sintering temperatures at 1,000 ℃ and high Ga content above 0.3, coarsening of grains occurred. This resulted in the formation of many grain boundaries, leading to low sinterability. These two factors, the impurity and grain boundary, have an enormous impact on the properties of Li_1+XGa_XTi_2-X(PO₄)₃. The Li_1.3Ga_0.3Ti_1.7(PO₄)₃ pellet sintered at 900 ℃ was denser than those sintered at other conditions, showing the highest total ion conductivity of 7.66 × 10^-5 S/cm at room temperature. The total activation energy of Li-ion transport for the Li_1.3Ga_0.3Ti_1.7(PO₄)₃ solid-state electrolyte was estimated to be as low as 0.36 eV. Although the Li_1+XGa_XTi_2-X(PO₄)₃ sintered at 1,000 ℃ had a relatively high apparent density, it had less total ionic conductivity due to an increase in the grain-boundary resistance with coarse grains.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.37 no.3
• /
• pp.297-303
• /
• 2024

In this study, KTN heterolayer thin films were fabricated by alternately stacking films of K(Ta_0.70Nb_0.30)O₃ and K(Ta_0.55Nb_0.45)O₃ synthesized using the sol-gel method. The sintering temperature and time were 750℃ and 1 hour, respectively. All specimens exhibited a polycrystalline pseudo-cubic crystal structure, with a lattice constant of approximately 0.398 nm. The average grain size was around 130~150 nm, indicating relatively uniform sizes regardless of the number of coatings. The average thickness of a single-coated film was approximately 70 nm. The phase transition temperature of the KTN heterolayer films was found to be approximately 8~12℃. Moreover, the 6-coated KTN heterolayer film displayed an excellent dielectric constant of about 11,000. As the number of coatings increased, and consequently the film thickness, the remanent polarization increased, while the coercive field decreased. The 6-coated KTN heterolayer film exhibited a remanent polarization and coercive field of 11.4 μC/cm² and 69.3 kV/cm at room temperature, respectively. ΔT showed the highest value at a temperature slightly above the Curie temperature, and for the 6-coated KTN heterolayer film, the ΔT and ΔT/ΔE were approximately 1.93 K and 0.128×10^-6 K·m/V around 40℃, respectively.

• Korean Journal of Radiology
• /
• v.23 no.11
• /
• pp.1055-1066
• /
• 2022

Objective: The clinical relevance of myosteatosis has not been well evaluated in patients with pancreatic ductal adenocarcinoma (PDAC), although sarcopenia has been extensively researched. Therefore, we evaluated the prognostic value of muscle quality, including myosteatosis, in patients with resectable PDAC treated surgically. Materials and Methods: We retrospectively evaluated 347 patients with resectable PDAC who underwent curative surgery (mean age ± standard deviation, 63.6 ± 9.6 years; 202 male). Automatic muscle segmentation was performed on preoperative computed tomography (CT) images using an artificial intelligence program. A single axial image of the portal phase at the inferior endplate level of the L3 vertebra was used for analysis in each patient. Sarcopenia was evaluated using the skeletal muscle index, calculated as the skeletal muscle area (SMA) divided by the height squared. The mean SMA attenuation was used to evaluate myosteatosis. Diagnostic cutoff values for sarcopenia and myosteatosis were devised using the Contal and O'Quigley methods, and patients were classified according to normal (nMT), sarcopenic (sMT), myosteatotic (mMT), or combined (cMT) muscle quality types. Multivariable Cox regression analyses were conducted to assess the effects of muscle type on the overall survival (OS) and recurrence-free survival (RFS) after surgery. Results: Eighty-four (24.2%), 73 (21.0%), 75 (21.6%), and 115 (33.1%) patients were classified as having nMT, sMT, mMT, and cMT, respectively. Compared to nMT, mMT and cMT were significantly associated with poorer OS, with hazard ratios (HRs) of 1.49 (95% confidence interval, 1.00-2.22) and 1.68 (1.16-2.43), respectively, while sMT was not (HR of 1.40 [0.94-2.10]). Only mMT was significantly associated with poorer RFS, with an HR of 1.59 (1.07-2.35), while sMT and cMT were not. Conclusion: Myosteatosis was associated with poor OS and RFS in patients with resectable PDAC who underwent curative surgery.