• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.10
• /
• pp.65-72
• /
• 1998

The BTA drilling chip is better for deep hole drilling than other self-piloting with pad drilling chips because the large length to diameter ratio allows a unique cutting force dispersion and better supplies the high pressure fluid. Therefore the BTA is useful for many tasks, such as coolant hole drilling of large scale dies, as well as tube seat drilling, which is essential for the heat exchanger, and variable component drilling for automobiles. Deep hole drilling has several significant problems, such as hole deviation, hole over-size, circularity, straightness, and surface roughness. The reasons for these problems, which often result in quality short comings, are an alignment of the BTA drilling system and the unbalance of cutting force by work piece and tool shape. This paper analyzes the properties through an experiment which com¬pared single-edge BTA drills with multiple-edge BTA drills, as well as the shapes of the tools to cause an unbalance of cutting force, and its effect on the precision of the worked hole. Conclusions are as follows. 1) In SMSSC drilling, 60m/min of BTA with single and multi-edged tools proved the best cutting condition and the lowest wear character. 2) The roundness got a little worse as cutting speed was increased, but surface roughness was hot affected. 3) It was proved that the burnishing torque of both drills approached 26%. which is almost the same as the 24% insisted on by Griffiths, and the dispersion characteristic of the multi-edged BTA drill proved better than the single-edge BTA drill.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.75-79
• /
• 1996

가공품 중에서 구멍가공이 차지하는 비율은 매우 높으며 또한 가공정밀도가 요구되어진다. 그러나구멍의 직경에 비하여 길이가 길어지면 칩의 배출, 절삭날부의 윤활이 어려워지고, 공구의 진동문제가있기 때문에 일반적인 가공으로는 불가능할 경우가 많다. 따라서 이에 적절한 가공방법은 고압력의 절삭유를 공급할 수 있는 공구를 이용하여 가공할 수 있으며, 그 대표적인 방법으로는 Spade Drill, Gun Drill, 및 BTA Dill에 의한 깊은구멍가공봅이다. 본 연구에서는 Single Tube BTA 드릴링 시스템에서 Single Edge BTA Drill을 사용 하여 깊은 구멍을 가공할 때 공작물 SM55C의 최적절삭 조건의 선정과 공구수명에 대하여 실험을 통하여 분석 하고자 하였다.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.9
• /
• pp.43-49
• /
• 1998

The deep hole drilling has an increasing demands because of its wide range applications and its good productivity. The BTA drills are capable of machining for having a large length to diameter ratio in single pass to higher degree of accuracy and surface finish. It's really necessary that the investigation for the deep hole drilling by the BTA drill because its required quality should be satisfied with single pass. This thesis deal with the experimental results obtained during single tube BTA system machining on SM55C steel for different machining conditions. The results of the investigation on the optimum cutting condition selecting and tool life reveals as follows. (1) The optimum cutting condition was cutting speed, V = 42 m/min and feed speed. F = 90 mm/min and the tool life was about 10 meters. (2) Surface roughness was $12\mum$ and the roundness was less using $16mum$single edge BTA drill in testing cutting condition.