• Journal of Welding and Joining
• /
• 제34권6호
• /
• pp.42-46
• /
• 2016

Hydrogen assisted cracking (HAC) is one of the most complicated problem in welding. Huge amount of studies have been done for decades. Based on them, various standards have been established to avoid HAC. But it is still a chronic problem in industrial field. It is well known that the main causes of the hydrogen crack are residual stress, crack susceptible micro structures and a certain critical level of hydrogen concentration. Even though the exact generating mechanism is unclear till today, it has been reported that the hydrogen level in the weld metal should be managed less than a certain amount to prevent it. Matsuda studied that the residual hydrogen level in the weld metal can be varied even if the initial hydrogen content is same. It is also insisted in this report that the residual hydrogen concentration is in stronger correlation with hydrogen crack than the initial hydrogen content. But, in practical point of view, the residual hydrogen is still hard to consider because measuring hydrogen level is time and cost consuming process. In this regard, numerical analysis is the only solution for considering the residual hydrogen content. Meanwhile, Takahashi showed the possibility of predicting the residual hydrogen by a rigorous FE analysis. But, few commercial software suitable for solving the weld metal hydrogen has been reported yet. In this study, two dimensional thermal - hydrogen coupled analysis was developed by using the commercial FE software MARC. Since the governing equation of the hydrogen diffusion is similar to the heat transfer, it is shown that the heat transfer FE analysis in association with hydrogen diffusion property can be used for hydrogen diffusion analysis. A series of simulation was performed to verify the accuracy of the model. For BOP (Bead-On-Plate) and the multi-pass butt welding simulations, remaining hydrogen contents in the weld metal is well matched with measurements which are referred from Kim and Masamitsu.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.365-369
• /
• 2004

Recently, Inconel 625 is used widely in offshore processing piping in order to extend the maintenance tenn and improve the quality of anti-corrosion. According to the resistance to attack in various corrosive media at temperatures from $200^{\circ}C$ to aver $1090^{\circ}C$, in combination with good low- and high-temperature mechanical strength. In general, High quality weldments for this material are readily produced by commonly used processes. in recent years, the flux cored arc welding(FCAW) process is becoming more popular due to higher deposition rate and a better weld quality as compared to the shielded metal arc welding (SMAW) process, at the same time, exhibiting equally good weld metal toughness similar to the SAW process. In this study, the weldability and weldment characteristics(mechanical properties and corrosive environment) of Inconel 625 are considered in FCAW weld associated with the several weld shielding gases($80\%Ar\;+\;20\%\;CO_2,\;50\%Ar\;+\;50\%\;CO_2,\;100\%\;CO_2$) in viewpoint of welding productivity.

• Journal of Welding and Joining
• /
• 제26권6호
• /
• pp.48-53
• /
• 2008

Although Magnetic Pulse Welding(MPW) is not a recently developed technique, it has gained the attention of the automotive industry. MPW has become an accepted welding process because it enables the joining of similar, and dissimilar materials, with a very short cycle time, without the need for filler metal and gases. In this study, the effect of the stand-off distance on the weld strength has been investigated. The compressive strength of the MPW joints was evaluated using UTM. The interface of weld, IMC composition and morpology were studied by SEM and EDS. It was concluded that the stand-off distance and the voltage are the main parameters influencing the strength of weld. In case of too high stand-off distance, it influenced harmful effect because of the resistance of deformation.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1995년도 특별강연 및 춘계학술발표 개요집
• /
• pp.91-93
• /
• 1995

A study was made to examine the effects of post-weld heat treatment (PWHT) on the toughness and microstructures in the weld heat-affacted zone(HAZ) of Cu-bearing HSLA-100 steel. The Gleeble thermal/mechanical simulator was used to simulate the weld HAZ. The behavior of Cu-precipitates in HAZ is similar to that in base plate. PWHT at 55$0^{\circ}C$ shows highest hardness and lowest toughness, whereas PWHT at $650^{\circ}C$ shows reasonable toughness. Cu precipitated during agcing for increasing the strength of base metal is dissolved during single thermal cycle to 135$0^{\circ}C$ and is precipitated little on cooling and heating during subsequent weld thermal cycle. It precipitates by introducing PWHT.

• 대한기계학회논문집A
• /
• 제39권10호
• /
• pp.979-984
• /
• 2015

본 논문에서는 국내 가동 중인 원자력발전소의 안전주입노즐을 대상으로 안전단의 길이와 동종금속용접부의 두께가 이종금속용접부의 응력분포에 미치는 영향을 평가하였다. 이를 위해 4가지의 서로 다른 안전단 길이와 4가지의 서로 다른 동종금속용접부 두께를 고려한 상세 2차원 유한요소 열해석 및 응력해석을 수행하였다. 유한요소해석 결과 동종금속용접부의 두께는 안전단의 길이가 짧은 경우 축방향 응력에 어느 정도 영향을 미쳤으나 원주방향 응력에는 거의 영향을 미치지 않았다. 안전단의 길이는 길이가 증가함에 따라 내면에서의 축방향 및 원주방향 응력값이 증가하는 것으로 나타났으나 특정 안전단 길이를 기준으로 응력분포가 구분되는 경향을 나타냈다.

• Journal of Biosystems Engineering
• /
• 제10권1호
• /
• pp.76-82
• /
• 1985

To investigate the influence of annealing heat treatment on the mechanical properties at the various weld zone, an experimental study was performed for the structural alloy steel. The results obtained from the experimental works are as follows: 1. Hardness and tensile strength showed the highest value at the heat affected zone, which was 5mm apart from bond zone. With increasing of annealing temperature, hardness and tensile strength were decreased at every weld zone, and bound in heat affected zone was increased. 2. Impact strength was the highest at the filler metal, and increased with increment of annealing temperature at filler metal and base metal. However, both at bond and heat affected zones, impact strength was increased from $700^{\circ}C$ of annealing temperature, and was decreased again over $900^{\circ}C$. 3. Mutual relationship between the mechanical properties at filler and base metals showed a similar linearty to that the common structural steel did. However, it varied unsteadly both at bond and heat affected zones. 4. It may be concluded that proper annealing temperature is $700^{\circ}C$ from the viewpoint of hardness, tensile and impact strength.

• 대한기계학회논문집A
• /
• 제33권1호
• /
• pp.72-81
• /
• 2009

This paper provides simulational round robin test results for welding residual stress prediction of safety/relief nozzle. To quantify the welding variables and define the recommendation for prediction and determination of welding residual stress, 6 partners in 5 institutes participated in round robin test. It is concluded that compressive axial and hoop residual stress occurs in dissimilar metal weld and pre-existing residual stress distribution in dissimilar metal weld was affected by similar metal weld due to short length of safe end. Although the reason for the deviation among the results was not pursued further, the effect of several key elements of FE analyses on welding residual stress was investigated in this paper.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.79-82
• /
• 2008

In this paper, results of simulational round robin test on residual stress prediction was provided. Welding residual stress is one of the reasons for primary water stress corrosion cracking in PWR. Therefore, quantifying the welding variables and defining the recommendation for prediction welding residual stress is important. Through the round robin test, it is known that compressive axial and hoop residual stress occurs in dissimilar metal weld and pre-existing residual stress distribution in dissimilar metal weld was affected by similar metal weld due to short length of safe end.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.100-100
• /
• 2009

본 논문에서는 원자력발전소 1차 계통의 스테인리스강 저합금강 이종금속용접부 및 스테인리스강 동종용접부의 잔류응력을 평가하고 스테인리스강 용접부의 응력부식균열 민감성에 대해 고찰하였다. 노즐 안전단의 이종금속용접부 및 안전단 배관의 동종용접부 제작 및 소재가공에 의행 생성되는 잔류응력을 예측하기 위해 열 탄소성 유한요소법 수치해석을 수행하였으며, 용접공정과 함께 표면의 잔류응력에 기여하는 절삭 및 연삭가공과 소재의 담금질 공정을 열 탄소성적으로 모사하였다. 전산해석 결과, 스테인리스주강의 담금질 잔류응력은 무시할 수 없는 상당한 크기이므로 배관 용접잔류응력 평가 시 소재의 담금질 효과를 고려해야 할 것으로 판단된다. 이종금속 용접과 동종금속 용접공정이 보수용접 없이 정상적인 절차(내면에서 외면으로 적층)로 완성된다면, 냉각재 환경에 노출되는 용접부 내면의 잔류응력은 재료의 응력부식균열 민감성에 영향을 주지 않을 것으로 판단된다. 한편, 안전단 배관 동종용접부의 연삭가공에 의해 내면의 잔류응력이 크게 상승하는 것으로 예측되었으므로, 내면의 연삭가공 이후 표면잔류응력 완화처리(예, 버핑)가 필요하다.

• Journal of Welding and Joining
• /
• 제30권2호
• /
• pp.76-80
• /
• 2012

In this study, the effect of the welding current on the hardness characteristics and microstructure in the resistance spot welding of 1GPa grade cold-rolled DP steel was investigated, Also, correlation between the hardness and microstructure was discussed. In spite of the change in the welding current, the hardness distributions near weld was similar. the hardness in the HAZ and the fusion zone was higher than that of the base metal and the hardness in the fusion zone was variated with the location. Especially, the hardness of HAZ adjacent to the base metal showed maximum value, and softening zone in the base metal adjacent to HAZ was found. With the increasing of welding current, there were no difference in maximum hardness and average hardness in the fusion zone were, but the hardness of the softening zone reduced. The difference in the hardness in each location of weld due to grain size of prior austenite. The softening of the base metal occurred by tempering of the martensite.