• Journal of Sensor Science and Technology
• /
• v.16 no.1
• /
• pp.77-83
• /
• 2007

Nanoporous silica aerogels with various surface modifiers were prepared by ambient drying process. Tetraethylorthosilicate (TEOS) were used a raw material. Ambient drying process for various surface modifier was studied in the point of view of a crack-free monolith and thin films and low cost. Various kinds of surface modifiers like as hexamethyldisilazane (HMDSZ), trimethlychlorosilane (TMCS), methlytriethoxylsilane (MTES), and methlytrimethoxysilane (MTMS) were studied in order to enhance hydrophobicity for the silica aerogel. Surface modified aerogels were evaluated by FT-IR, TG, BET, SEM and wetting angle measurement. Homogeneous and crack-free aerogels were obtained by modifying the HMDSZ and the TMCS. However silica xerogel was obtained when modified with MTMS, MTES.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.4
• /
• pp.15-20
• /
• 2022

Aerogel is a material having a nanopore structure based on a high porosity. Due to this high porosity, it has excellent properties not found in conventional materials, but its application has been limited due to low mechanical strength. Therefore, to improve the mechanical strength of the aerogel, polyurea crosslinking was introduced and a precursor having an amine group essential for polyurea polymer formation was selected to synthesize a polyurea crosslinked aerogel composite. In addition, the crosslinking of polyurea was adjusted according to the number of amine groups present in aminosilane. It was confirmed through various analyses that the nanopore structure of the aerogel was maintained to have mesopores. The aerogel thus formed was able to improve the mechanical strength by about two times, and it was confirmed through field emission scanning electron microscope analysis that a one-dimensional polymer was formed on the silica aerogel surface through the introduction of ethylene diamine. The one-dimensional polymer thus formed has improved mechanical properties, resulting in securing an elastic modulus of about 2.66 MPa.

• Steel and Composite Structures
• /
• v.47 no.5
• /
• pp.633-644
• /
• 2023

Taking a look at the previously published papers, it is revealed that there is a porosity index limitation (around 0.35) for the mechanical behavior analysis of the functionally graded porous (FGP) structures. Over mentioned magnitude of the porosity index, the elastic modulus falls below zero for some parts of the structure thickness. Therefore, the current paper is presented to analyze the vibrational behavior of the FGP Timoshenko beams (FGPTBs) using a novel refined formulation regardless of the porosity index magnitude. The silica aerogel foundation and various hydrothermal loadings are assumed as the source of external forces. To obtain the FGPTB's properties, the power law is hired, and employing Hamilton's principle in conjunction with Navier's solution method, the governing equations are extracted and solved. In the end, the impact of the various variables as different beam materials, elastic foundation parameters, and porosity index is captured and displayed. It is revealed that changing hygrothermal loading from non-linear toward uniform configuration results in non-dimensional frequency and stiffness pushing up. Also, Al - Al2O3 as the material composition of the beam and the porosity presence with the O pattern, provide more rigidity in comparison with using other materials and other types of porosity dispersion. The presented computational model in this paper hopes to help add more accuracy to the structures' analysis in high-tech industries.

• Journal of the Korean Ceramic Society
• /
• v.34 no.4
• /
• pp.357-367
• /
• 1997

A fast process for producing pure silica glasses with the reproducibility of 100% by means of sintering of silica aerogels was optimized. The density of silica glasses synthesized by heat-treating upto 110$0^{\circ}C$ with the heating rate of 0.1$^{\circ}C$/min was 2.197 g/㎤. Synthetic silica glasses(5 mm thickness) exhibited the transmittance of 92% in the near IR range as well as they had the excellent mechanical properties such as flexural strength of 162 MPa and hardness of 778 kg/$\textrm{mm}^2$.

• Journal of the Korean Electrochemical Society
• /
• v.7 no.1
• /
• pp.38-43
• /
• 2004

Porous carbon aerogel-silica gel composite materials were used as the electrodes of capacitive deionization(CDI) process, which were prepared by a paste rolling method. The electrochemical parameters such at current values, coulombs af a function of cycle, and CDI efficiencies were investigated for 10th and 100th cycles in 1,000ppm NaCl solution. Carbon aerogel-silica gel composite electrodes showed good wet-ability and higher mechanical strengths even under the NaCl solutions as well. In our experimented runs, all of the composite electrodes also are showed good cycle-ability without destroy of active material during cycles and decreased manufacturing times by $50\%$. Conclusively, the adding of silica gel powder to carbon aerogel leads to the effective performance of CDI process due to effective utilization of active materials by increasing the wet-ability and mechanical hardness.

• Journal of the Korean Ceramic Society
• /
• v.44 no.3 s.298
• /
• pp.162-168
• /
• 2007

Silica wet gels were prepared ken water glass ($29\;wt%\;SiO_{2}$) by using Amberlite as a ion exchange resin. After washing in distilled water, the wet gels were further aged in a solution of TEOS/EtOH to strengthen of 3-dimensional network structure. As increase TEOS content in aging solution, BET surface area and porosity of the ambient dried silica aerogels were significantly decreased, and average pore diameter was also decreased 30 nm to -10 nm. Also, higher density and compressive strength were obtained in case of higher TEOS content. This is due to precipitation of $SiO_{2}$ nano particles by TEOS. Hence, TEOS addition plays an important role of both strengthening and stiffness of silica wet gel network. By adding over 30 vol% TEOS, a crack-free monolithic silica aerogel tiles were obtained and its density, compressive strength, and thermal conductivity were shown $0.232g/cm^{3}$, 7.3 MPa, and 0.029 W/mk, respectivly.

• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.4
• /
• pp.135-141
• /
• 2020

The silica aerogels with benzene-bridged were designed to have uniform network structure, ordered pore structure, improved mechanical properties and excellent textural properties. Adding organic to enhance the mechanical properties of silica aerogels is a common method, but textural properties of aerogels with organic are reduced due to the organic-inorganic phase separation. In this paper, we use a simple and low-cost method to increase mechanical properties while maintaining textural properties of SiO2 aerogels. Two types of benzene-bridged precursors were prepared to study the effect of the number of hydroxyl band on the textural and mechanical properties. The porous silica aerogel was prepared by a simple, cost effective and pollution-free sol-gel method. This method does not require additional silylating reagents. The benzene-bridged silica aerogel samples prepared had excellent textural properties, high specific surface area (1,326 ㎡/g), porous structure and hydrophobicity (>140°). The mechanical strength of 2T4 is more than 5 times that of pure silica aerogel.

• Journal of Sensor Science and Technology
• /
• v.15 no.5
• /
• pp.371-377
• /
• 2006

Nano porous, transparent silica aerogels monoliths were prepared under ambient drying (1 atm, $270^{\circ}C$) condition by the combination of sol-gel process and surface modification with subsequent heat treatment. Three kinds of solvent, n-hexane, n-heptane and xylene, were selected in the point view of low surface tension and vapor pressure in order to restrain a formation of cracks during drying. Crack-free silica aerogels with over 93 % of porosity and below $0.14g/cm^3$ of density were obtained by solvent exchange and surface modification under atmosphere condition. Optimum solvent was confirmed n-heptane among these solvents through estimation of FT-IR, TGA, BET and SEM. Modified silica aerogel exhibited a higher porosity and pore size compare to unmodified aerogels. Hydrophobicity was also controled by C-H and H-OH bonding state in the gel structure and heat treatment over $400^{\circ}C$ effects to the hydrophobicity due to oxidation of C-H radicals.

• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.4
• /
• pp.143-148
• /
• 2018

Sodium silicate based silica aerogels are lower in cost than silica alkoxide based silica aerogels, but the demand is decreasing as their physical properties are lowered. In this research, acetonitrile as a drying control chemical additive (DCCA) is added in the sol state to improve the pore-structural properties of sodium silicate based silica aerogel by preventing the agglomeration of particles and cross-linked bond. The sodium silicate based silica aerogel by ambient pressure drying were prepared by sol-gel process. Acetonitrile/$Na_2SiO_3$ molar ratio of 0, 0.05, 0.1, 0.15, and 0.2 was added to the sol state. The physical properties of the final product were analyzed using Fourier transform infrared, contact angle measurement, Brunauer-Emmett-Teller and Barrett-Joyner-Halenda measurements and field emission scanning electron microscopy. It was confirmed that the sample with adding 0.15 molar ratio of acetonitrile and sodium silicate showed a high specific surface area ($577m^2/g$), a high pore volume (3.29 cc/g), and a high porosity (93%) comparable to the pore-structural properties of silica alkoxide based silica aerogels.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2000.04a
• /
• pp.128.1-128.1
• /
• 2000