• JSTS:Journal of Semiconductor Technology and Science
• /
• 제16권6호
• /
• pp.793-799
• /
• 2016

A multi-purpose sensor interface that provides dual-mode operation of fingerprint sensing and physiological signal detection is presented. The dual-mode sensing capability is achieved by utilizing inter-pixel shielding patterns as capacitive amplifier's input electrodes. A prototype readout circuit including a fingerprint panel for feasibility verification was fabricated in a $0.18{\mu}m$ CMOS process. A single-channel readout circuit was implemented and multiplexed to scan two-dimensional fingerprint pixels, where adaptive calibration capability against pixel-capacitance variations was also implemented. Feasibility of the proposed multi-purpose interface was experimentally verified keeping low-power consumption less than 1.9 mW under a 3.3 V supply.

• Journal of information and communication convergence engineering
• /
• 제6권3호
• /
• pp.270-274
• /
• 2008

This paper proposes an advanced signal processing circuit for a fingerprint sensor based on ridge resistivity. A novel fingerprint integrated sensor using ridge resistivity variation resulting from ridges and valleys on the fingertip is presented. The pixel level simple detection circuit converts from a small and variable sensing current to binary voltage out effectively. The sensor circuit blocks were designed and simulated in a standard CMOS 0.35 ${\mu}m$ process.

• Journal of information and communication convergence engineering
• /
• 제13권3호
• /
• pp.189-196
• /
• 2015

In this paper, we present a rotating auto-zeroing offset cancellation technique, which can improve the performance of touch screen sensing circuits. Our target touch screen detection method employs multiple continuous sine waves to achieve a high speed for large touch screens. While conventional auto-zeroing schemes cannot handle such continuous signals properly, the proposed scheme does not suffer from switching noise and provides effective offset cancellation for continuous signals. Experimental results show that the proposed technique improves the signal-to-noise ratio by 14 dB compared to a conventional offset cancellation scheme. For the realistic simulation results, we used Cadence SPECTRE with an accurate TSP model and noise source. We also applied an asymmetric device size (10% MOS size mismatch) to the OP Amp design in order to measure the effectiveness of offset cancellation. We implemented the proposed circuit as part of a touch screen controller system-on-chip by using a Magnachip/SK Hynix 0.18-µm complementary metal-oxide semiconductor (CMOS) process.

• 센서학회지
• /
• 제14권1호
• /
• pp.28-32
• /
• 2005

In this paper, a CMOS integrated detection circuit for capacitive type fingerprint sensor signal processing is described. We designed a detection circuit of charge-sharing sensing scheme. The proposed detection circuit increases the voltage difference between a ridge and valley. The test chip is composed of $160{\times}192$ array sensing cells (12 by $12.7{\;}mm^{2}$). The chip was fabricated on a 0.35 m standard CMOS process. Measured difference voltage between a ridge and valley was 0.95 V.

• Current Optics and Photonics
• /
• 제7권1호
• /
• pp.38-46
• /
• 2023

Optical Fourier-domain reflectometry (OFDR) sensors have been widely used to measure distances with high resolution and speed in a noncontact state. In the electroplating process of a printed circuit board, it is critically important to monitor the copper-plating thickness, as small deviations can lead to defects, such as an open or short circuit. In this paper we employ a phase-based OFDR sensor for in situ relative distance sensing of a sample with nanometer-scale resolution, during electroplating. We also develop an optical-path difference (OPD)-regulated sensing probe that can maintain a preset distance from the sample. This function can markedly facilitate practical measurements in two aspects: Optimal distance setting for high signal-to-noise ratio OFDR sensing, and protection of a fragile probe tip via vertical evasion movement. In a sample with a centimeter-scale structure, a conventional OFDR sensor will probably either bump into the sample or practically out of the detection range of the sensing probe. To address this limitation, a novel OPD-regulated OFDR system is designed by combining the OFDR sensing probe and linear piezo motors with feedback-loop control. By using multiple OFDR sensors, it is possible to effectively monitor copper-plating thickness in situ and uniformize it at various positions.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2004년도 ICEIC The International Conference on Electronics Informations and Communications
• /
• pp.82-85
• /
• 2004

This paper proposes an advanced circuit for the capacitive type fingerprint sensor signal processing and an effective isolation structure for minimizing an electrostatic discharge(ESD) influence and for removing a signal coupling noise of each sensor pixel. The proposed detection circuit increases the voltage difference between a ridge and valley about $80\%$ more than old circuit. The test chip is composed of $160\;\times\;192$ array sensing cells $(9,913\times11,666\;um^2).$ The sensor plate area is $58\;\times\;58\;um^2$ and the pitch is 60um. The image resolution is 423 dpi. The chip was fabricated on a 0.35um standard CMOS process. It successfully captured a high-quality fingerprint image and performed the registration and identification processing. The sensing and authentication time is 1 sec(.) with the average power consumption of 10 mW at 3.0V. The reveal ESD tolerance is obtained at the value of 4.5 kV.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2004년도 Asia Navigation Conference
• /
• pp.29-36
• /
• 2004

The paper describes recent experimental results on the development of Digital Magnetic Compass (DMC), which can provide smart automatic correction functions to the magnetic interferences. The design methodology of magnetic sensing circuit with ring-core fluxgate sensor is represented. The performance results of the sensing circuits are discussed with error analysis by polynomial regressions. As test results, the sensing circuit filtered only the second harmonic signal that is proportional to the direction of earth's magnetic field, and it leads to the obtainment of bearing information. In addition, the total residual errors of DMC can be analyzed by the adoption of polynomial regressions. It shown that the possibility of high precise DMC, in the future.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 B
• /
• pp.1267-1269
• /
• 2000

New switching signal pattern for four switches is proposed to prevent the shortage of PWM ac choppers. In the proposed technique, four signals to four power switches are generated without current transformer, while the conventional technique requires sensing the polarity of input voltage by voltage comparator and checking the direction of input current by the current transformer. The signal circuit built by the proposed technique is simple, and reduces also the switching loss.

• Journal of information and communication convergence engineering
• /
• 제14권2호
• /
• pp.106-114
• /
• 2016

Differential sensing methods are more effective in alleviating panel noise than single-line sensing, and thus have been increasingly used in the touch screen industry. However, they have a drawback: they tend to cancel out multiple touches and need touch position recovery algorithms. This paper introduces a novel algorithm of touch position recovery for differential sensing, which is a low-complexity but high-accuracy approach for determining multiple touch positions. We have implemented the proposed method in a touch screen controller system on a chip. In the simulation experiments using realistic touch screen models and a differential sensing circuit, the algorithm exhibited a high detection performance of a signal-to-noise ratio gain of up to 52.21 dB. Therefore, we can conclude that the proposed method is substantially more accurate than the previous method. Further, the proposed method incurs little or no overhead in terms of the detection speed and the chip size.

• 로봇학회논문지
• /
• 제4권4호
• /
• pp.320-326
• /
• 2009

This paper proposed a new magnetic field detection algorithm to detect metal pieces in food producing processes. This algorithm can detect mixed metal pieces by sensing magnetic field. Some metal pieces are passed through an over-current circuit to magnetize them. The magnetic field sensor can detect the change in the magnetic field on theconveyor belt caused by the flow of the metal pieces in the food product. However, such a method detects the output of signals that change their amplitude and phase according to the movement of the conveyor belt with the food product, in which the equilibrium of the positive signal that is created in the receiver coil loses its balance due to the magnetized material. This includes not only the signal elements resulting from the effect of the alternating magnetic fields of the mixed metals, but also the signal elements resulting from the effect of the alternating magnetic fields of the examined object itself.