• Aerospace Engineering and Technology
• /
• v.8 no.1
• /
• pp.66-72
• /
• 2009

In order to verify the operability of a GPS receiver which is one of the KSLV-I onboard electrical equipments under the vacuum conditions, this paper describes the operation methods and performance results of the GPS receiver under the thermal-vacuum and vacuum environments. The damages and degradations of electrical parts of the GPS receiver caused by the pressure change and high-degree vacuum conditions are analyzed in terms of tracking and navigation capabilities through the signal-to-noise ratio and navigation error.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.1A
• /
• pp.18-30
• /
• 2004

In this paper, the calibration problem of an asynchronous CDMA-based antenna array is studied. A new iterative calibration algorithm for antenna array in the presence of frequency offset error is presented. The algorithm is applicable to a non-linear array and does not require a prior knowledge of the (direction of arrivals) DOAs of the signals of any user, and it only requires the code sequence of a reference user. The algorithm is based on the two step procedures, one for estimating both channel and frequency offset and the other for estimating the unknown array gain and phase. Consequently, estimates of the DOAs, the multi-path impulse response of the reference signal sources, and the carrier frequency offset as well as the calibration of antenna array are provided. The performance of the proposed algorithm is investigated by means of computer simulations and is verified by using field data measured through a custom-built W-CDMA test-bed.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.1
• /
• pp.89-96
• /
• 2009

This paper describes the intelligent robot's hand with three finger sensors for a humanoid robot. In order to grasp an unknown object safely, the intelligent robot's hand should measure the mass of the object, and determine the grasping force using the mass, finally control the grasping force using the finger sensors and the controller. In this paper, the intelligent robot's hand for a humanoid robot was developed. First, the six-axis force/moment sensor was manufactured. second, three finger force sensors were designed and fabricated, third, the high-speed controller was manufactured using DSP(digital signal processor), finally, the characteristic test for determining a grasping force and for grasping an unknown object safely It is confirmed that the hand could grasp an unknown object safely.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.930-935
• /
• 2001

The experimental characterization of hydrodynamic bearing spindle motor is performed for the practical implementation of high-performance hard disk drive system. Firstly, the design concept of hydrodynamic bearing for the disk drive system is addressed including the herringbone grooved journal bearing, the spiral grooved thrust bearing, capillary seal design, and the viscous pumping of fluid. Secondly, the experimental evaluation is performed for the disk drive system in which the hydrodynamic bearing spindle motor is implemented and its dynamic performances are compared with conventional ball-bearing spindle motor. The key parameters include NRRO(Non Repeatable Run-Out), disk dynamics, acoustics, and resultant PES (Position Error Signal). Finally, the external gyro-exciting test results including 200k CSS(Continuous Start-Stop) on three angular attitudes(0,90, 180 degree) are presented in order to verify the practical reliability of disk drive system subject to the gyro-motion of hydrodynamic bearing spindle motor.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.9
• /
• pp.1812-1823
• /
• 1994

In this paper, we focus on the simulation of receiver algorithms for the Q-CDMA reverse link modem to analyze its structure and performance. Receiver algorithm is to be characterized by processing a large amount of data for reliable data transmission through poor mobile channel environment. According to Q-CDMA receiver scheme, we connect the code acqusition and code tracking models for despreading of input signals and the RAKE structure demodulator used to resolve the time diversity signal due to multipath propagation. And this connected system is under test. The bit error rates are found for an arbitrary user under the AWGN and multipath fading environments.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2003.11a
• /
• pp.590-595
• /
• 2003

An Exponential experiment system which is composed of a neutron detector, a signal analysis system and a neutron source, Cf-252 has been installed in order to experimentally determine the neutron effective multiplication factor for a PWR spent fuel assembly. The axial background neutron flux is measured in a preliminary performance test. From the results, the spacer grid position is determined to be consistent with the design specifications within a 2.3% relative error. The induced fission neutron for four of the assemblies is also measured by scanning the neutron source, Cf-252 or the neutron detector. The exponential decay constants have been evaluated by the application of the Poisson regression to the net induced fission neutron counts. The measured keffs determined on the basis of the exponential decay constants of Cl5 appeared to be 0.541, 0.540, 0.597 and 0.556, respectively, which are comparable with 0.55195$\pm$0.00232 of the MCNP calculation.

• The Journal of Korea Robotics Society
• /
• v.15 no.3
• /
• pp.212-220
• /
• 2020

This paper deals with a strategy of gain optimization for the kinematic control algorithm of a wire-driven surgical robot. The proposed controller consists of the closed-loop inverse kinematics with the back-calculation method. The closed-loop inverse kinematics has 18 PID control gains, and the back-calculation method has 6 gains. An efficient strategy is designed to optimize 18 values first and then the remaining 6 values. The optimal gain sets are searched under the step input with performance indices. In this gain optimization, the objective function is defined as the minimum value of signal-to-noise ratio of the performance indices for 6 DoF (Degree-of-Freedom) motion that is based on the Taguchi method, and the constraints are applied to obtain stable responses for each motion evenly. The gain sets obtained are verified by simulations using the test trajectories. In comparative results, the optimal gain value based on the performance index combined with ISE (integral of square error) and settling time showed the best control performance.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.1
• /
• pp.31-39
• /
• 2016

This paper describes the design of an ankle rehabilitation robot for the force measurement of a severe stroke patient staying in a bed ward. The developed ankle rehabilitation robot was attached to a three-axis force/torque sensor that could detect force Fx, Fz, and torque Tz and measure the ankle rotation force (Fx) exerted on the ankle and the signal force Fz and torque Tz to be used as a safety device. The robot was designed and manufactured for bedridden stroke patients, and the robot program was manufactured to perform the flexibility rehabilitation exercise for ankle bending and to measure the ankle force to judge the degree of rehabilitation. According to the result of the characteristics test of the developed rehabilitation robot, it was safely operated while the ankle-bending flexibility rehabilitation exercise and the emergency situation were performed. Therefore, it is thought that the developed rehabilitation robot can be used for severe stroke patients.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1880-1884
• /
• 2000

The discrete wavelet transform is utilized as preprocessing of Neural Network(NN) to identify aging state of internal partial discharge in transformer. The discrete traveler transform is used to produce wavelet coefficients which are used for Classification. The statistical parameters (maximum of wavelet coefficients, average value, dispersion, skewness, kurtosis) using the wavelet coefficients are input into an back-propagation neural network. The neurons whose weights have obtained through Result of Cross-Validation. The Neural Network learning stops either when the error rate achieves an appropriate minimum or when the learning time overcomes a constant value. The networks, after training, can decide if the test signal is Early Aging State or Last Aging State or normal state.

• ETRI Journal
• /
• v.38 no.1
• /
• pp.185-194
• /
• 2016

In this paper, a novel rate control scheme for low delay video coding of High Efficiency Video Coding (HEVC) is proposed. The proposed scheme is developed by considering a new temporal prediction structure of HEVC. In the proposed scheme, the relationship between bit rate and quantization step is exploited firstly to formulate an accurate quadratic rate-quantization (R-Q) model. Secondly, a method of determining the quantization parameters (QPs) for the first frames within a group of pictures is proposed. Thirdly, an accurate frame-level bit allocation method is proposed for HEVC. Finally, based on the proposed R-Q model and the target bit allocated for the frame, the QPs are predicted for coding tree units by using rate-distortion (R-D) optimization. We compare our scheme against that of three other state-of-the-art rate control schemes. Experimental results show that the proposed rate control scheme can increase the Bjøntegaard delta peak signal-to-noise ratio by 0.65 dB and 0.09 dB on average compared with the JCTVC-I0094 and JCTVC-M0036 schemes, respectively, both of which have been implemented in an HEVC test model encoder; furthermore, the proposed scheme achieves a similar R-D performance to Wang's scheme, as well as obtaining the smallest bit rate mismatch error of all the schemes.