• Proceedings of the KIEE Conference
• /
• 2006.04b
• /
• pp.182-184
• /
• 2006

A down-scaled simulator is developed to simulate typical faults in induction motor such as short-turn stator winding, broken rotor bar, dynamic and static air-gap eccentricity, bearing trouble, and mechanical unbalance. The simulator is used as an initial builder to develop design algorithm for real-time faults detecting system by processing an abnormal signal and characteristics in each fault.

• Journal of KSNVE
• /
• v.4 no.3
• /
• pp.365-375
• /
• 1994

Periodic longitudinal vibrations of a video and audio tape and the like used for transducing pictures and sounds may be induced by self-excited vibrations which are caused by frictions against the heads and guides, and their eccentricity, noncircularity or irregularity. It is important to analyze the longitudinal vibration of a tape because it causes distortions of a reproduced signal. It is difficult to measure directly the longitudinal vibration. In this paper a method estimating longitudinal vibration using impulse responses in the transverse direction is presented. And, the parameters boundary domain where the transverse and longitudinal vibration can be decoupled is introduced. In the domain where the both vibrations are decoupled, analytic methods using frequency characteristics and transient responses of the transverse vibration, respectively, are presented. The time domain method predicted more exactly the instantaneous phase of the longitudinal vibration than frequency domain method did.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1450-1454
• /
• 2000

In order to understand dynamic characteristics of centrifugal compressor supported foil bearing, of which normal operating speed is about 20,000 ${\sim}$ 50,000 rpm, the rotor whirl is measured using gap sensors. Not only critical speeds of rotor system but also stability of rotor whirl, which are main concerns of the turbo compressor system, are measured using gap sensors by varying the rotating speed the rotor. The stiffness characteristics of bearing system is shown to be almost invariant according to speed variation by the measurement of eccentricity. In addition, from the directional power spectral density function of the measured vibration signal, the isotropy stiffness characteristics of foil bearing system is discussed.

• Proceedings of the KIEE Conference
• /
• 2003.07d
• /
• pp.2146-2148
• /
• 2003

This paper present a modified repetitive control scheme for an optical storage system to track a periodic reference signal with dynamic change in period. Periodic disturbances can be adequately attenuated using the concept of repetitive control, provided the period is know. An optical storage system supports various speeds. To deal with time varying periodic disturbances, an proposed repetitive controller is turned based on repetitive control to change sampling frequency to follow the change of reference Period. A modified repetitive control scheme is proposed and implement on experimental set up of a optical disk driver.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.904-907
• /
• 2002

Optical disk drive device is improved in rotating speed for faster data reading. In the case of CD-ROM, rotating speed is over 10000 rpm in the practical use. As a result of high rotating speed, unexpected effects as like increasing disk fluctuation and acoustic noise are raised by the air friction on the rotating disk and the eccentricity of rotating parts. The overall acoustic noise of running CD-ROM could be classified into two different characterized noise. The first is the structural-borne noise which is generated from vibrating solid body. By the reason, the signal of structural borne noise has very similar to the signal of surface vibrating one. It has dense noise energy at specific frequency region. The other is the air-borne noise which is generated from turbulence or vortex caused by friction between disk and air. The signal of air-borne noise has no dominant peak point at acoustic pressure-frequency domain. The noise energy is widely distributed while comparatively high and large frequency region. The structural-borne noise could be reduced by reducing vibration of structure and in addition it's target reducing frequency is narrow. However the air-borne noise reduction is effectively needed of enclosing method for the noise source located near the disk surface because it is difficult to define target frequency point. In this study, the acoustic noise at driving CD-ROM is classified by the sides of it's character and tried to reduce the overall acoustic noise.

• Journal of Institute of Control, Robotics and Systems
• /
• v.9 no.2
• /
• pp.117-123
• /
• 2003

Rotational machines such as optical disk drives, hard disk drives, and so on are subject to periodic disturbances caused by their mechanical characteristics. In the meanwhile, it is well known that repetitive control rejects periodic disturbance effectively. This paper presents a practical application of repetitive control to the track-following servo of an optical disk drive. The repetitive control system is composed of two repetitive controllers which compensate for periodic disturbances generated by track geometry and eccentric rotation of disk and a feedback controller stabilizing the feedback loop. A robust stability for all plant uncertainties is proved using linear matrix inequalities (LMIs). In the controller design, a weighting function is introduced for the feedback controller to ensure a minimum loop gain and a sufficient phase margin. The repetitive controllers and the feedback controller are designed by solving an optimization problem which can consider the robust stability condition and the system performance. The developed repetitive control system is implemented in the digital control system with a 16-bit fixed-point digital signal processor (DSP). Through simulation and experiment. The feasibility of the proposed repetitive control system is verified.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.2
• /
• pp.38-44
• /
• 2021

To cater to the transition from single-color to multicolor/multi-material printing, this paper proposes a cartridge-replacing type multi-nozzle Fused Depositon Modeling(FDM) three-dimensional (3D) printer. In the test printing run, tool change failure/wobble/layer shift occurred. It was confirmed that improper support was the cause of this tool change failure. As a solution, spline and electromagnetic cartridges were designed. Wobble was caused by machine vibration and the motor stepping out. To minimize wobble, an additional Z-axis was installed, and the four-point bed leveling method was used instead of the three-point bed leveling method. The occurrence of layer shift was ascribed to the eccentricity of the Z-axis lead screw. Therefore, slit coupler was replaced with an Oldham type. In addition to the mechanical supplementation, the control environment was integrated to prevent accidents and signal errors due to wire connections. Before the final test printing run, a rectifier circuit was added to the motor to secure precise control stability. The final test printing run confirmed that the wobble/layer shift phenomenon was minimized, and the maximum error between layers was reduced to 0.05.

• Design & Manufacturing
• /
• v.15 no.4
• /
• pp.51-56
• /
• 2021

Piercing is the process of shearing a circular hole in sheet metal, whose high shear force makes it difficult to secure the durability of tools. In addition, uneven clearance between tools due to poor alignment of the piercing punch causes accelerated die wear and breakage of the tool. This study reviewed the feasibility of in-situ determining alignment failure during the piercing process by analyzing the signal deviation of a bolt-type piezo sensor installed inside the tool whose alignment level was controlled. Finite element analysis was performed to select the optimal sensor location on the piercing tool for sensitive detection of process signals. A well-aligned piercing process results in uniform deformation in the circumferential direction, and shearing is completed at a stroke similar to the sheet thickness. Afterward, a sharp decrease in shear load is observed. The misaligned piecing punch leads to a gradual decrease in the load after the maximum shear load. This gradual decrease is due to the progressive shear deformation that proceeds in the circumferential direction after the initial crack occurs at the narrow clearance site. Therefore, analyzing the stroke at which the maximum shear load occurs and the load reduction rate after that could detect the misalignment of the piercing punch in real-time.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.43 no.5 s.311
• /
• pp.80-88
• /
• 2006

In this paper we developed a novel system for automatic detection of mass type breast cancer on dense digital mammogram images. The new approaches presented in this paper are as follows: 1) we presented a method that stably decides the mass center and radius without being affected by image signal irregularity. 2) We developed a radial directional filter that is suitable to process mass image signal. 3) And we developed the multiple feature function based on mass shape spiculation, mass center homogeneity, and mass eccentricity, so as to determine mass-type breast cancer. When the proposed system is applied to dense mammographic images, the true 기arm rate is improved by 10% over a conventional system while the false alarm is increased by 1 per image.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.1
• /
• pp.132-137
• /
• 2006

The second part of paper related rotor failure is to evaluate that the axial magnetic flux measurement could be used as a tool of the condition monitoring system for the induction motor and to develope the diagnostic algorithm for the various fault in the electric motors. The magnetic leakage flux signal is captured by the flux coil located at the end of motor without the disturbance of the operation. And the signal is analyzed both time and frequency domain to detect the failure of the motor. Specific signature can be described in tin and frequency domain for each fault of the motor. The experimental test found that the rotor failures - broken rotor bar, broken end ing and rotor eccentricity, could be detected from the spectrum with high resolution. The method of detecting the rotor fault was found by analysing the specific frequency and the sideband of the rotor bar pass frequency from axial leakage flux spectrum. In addition the optimal flux coil and measuring equipment for the axial leakage flux measurement was verified and the diagnostic method for the detection of the rotor related failure was developed.