• Journal of Biomedical Engineering Research
• /
• v.32 no.1
• /
• pp.45-54
• /
• 2011

Cuff electrodes have a benefit for chronic electroneurogram(ENG) recording while minimizing nerve damage. However, the ENG signals are usually contaminated by electromyogram(EMG) activity from the surrounding muscle, the thermal noise generated within the source resistance, and the electric noise generated primarily at the first stage of the amplifier. This paper proposes a new cuff electrode to reduce the interference of EMG signals. An additional middle electrode was placed at the center of cuff electrode. As a result, the proposed cuff electrode achieved a higher signal-to-interference ratio compared to the conventional tripolar cuff. The cuff electrode was then assembled together with closure, headstage, and hermetic case including electronic circuits. This paper also presents a lownoise amplifier system to improve signal-to-noise ratio. The circuit was designed based on the noise analysis to minimize the electronic noise. The result shows that the total noise of the amplifier was below $1{\mu}V_{rms}$ for a cuff impedance of $1\;k{\Omega}$ and the common-mode rejection ratio was 115 dB at 1 kHz. In the current study, the performance of nerve cuff electrode system was evaluated by monitoring afferent nerve signals under mechanical stimuli in a rat animal model.

• Journal of Korean Society for Quality Management
• /
• v.46 no.3
• /
• pp.651-658
• /
• 2018

Purpose: The algorithm described in Lim(1998) is available to determine the sample size directly given specified significance level, power and signal-to-noise ratio. We research on the efficient determination of the sample size by visual methods. Methods: We propose three graphs for investigating the mutual relationship between the sample size r, power $1-{\beta}$ and the detectable signal-to-noise ratio ${\Delta}$. First graph shows the relationship between ${\Delta}$ and $1-{\beta}$ for the given r and it can be checked whether the power is sufficient enough. Second graph shows the relationship between r and ${\Delta}$ for the given power $1-{\beta}$. Third graph shows the relationship between r and $1-{\beta}$ for the given ${\Delta}$. It can be checked that which effects are sensitive to the efficient sample size by investigating those graphs. Results: In factorial design, randomized block design and the split plot design how to determine the sample size directly given specified significance level, power and signal-to-noise ratio is programmed by using R. A experiment to study the split plot design in Hicks(1982) is used as an example. We compare the sample sizes calculated by randomized block design with those by split plot design. By using graphs, we can check the possibility of reducing the sample size efficiently. Conclusion: The proposed visual methods can help an engineer to make a proper plan to reduce the sample size.

• Journal of IKEEE
• /
• v.14 no.1
• /
• pp.47-54
• /
• 2010

In this study, we analyzed the reduction of noise in a noise environment using 2, 3, 4 or 5 microphones in digital hearing aids. In order to be able to use this in actual digital hearing aids, we made the experiment microphone set similar to the behind-the-ear type (BTE) and then recorded the signal accordingly, with each situation. With the recorded signals, we reduced the noise in each signal by a noise reduction algorithm using multi-microphones. As a result, in the case of By comparing the SNR (Signal to Noise Ratio) and PESQ (Perceptual Evaluation of Speech) measurements, before and after the noise reduction, the results showed that the improvement in performance was highest when three or four microphones were used. Generally, when two or more microphones were used, we found that as the number of microphones increased there was an increase in performance.

• The Journal of the Acoustical Society of Korea
• /
• v.41 no.5
• /
• pp.507-517
• /
• 2022

The PhotoAcoustic Microscopy (PAM) has been proved to be a useful tool for biological and medical applications due to its high spatial and contrast resolution. PAM is based on transmission of laser pulses and reception of PA signals. Since the strength of PA signals is generally low, not only are high-performance optical and acoustic modules required, but high-performance electronics for imaging are also particularly needed for high-quality PAM imaging. Most PAM systems are implemented with a combination of several pieces of equipment commercially available to receive, amplify, enhance, and digitize PA signals. To this end, PAM systems are inevitably bulky and not optimal because general purpose equipment is used. This paper reports a PA signal receiving system recently developed to attain the capability of improved Signal to Noise Ratio (SNR) and Contrast to Noise Ratio (CNR) of PAM images; the main module of this system is a low noise, wideband signal receiver that consists of two low-noise amplifiers, two variable gain amplifiers, analog filters, an Analog to Digital Converter (ADC), and control logic. From phantom imaging experiments, it was found that the developed system can improve SNR by 6.7 dB and CNR by 3 dB, compared to a combination of several pieces of commercially available equipment.

• Journal of electromagnetic engineering and science
• /
• v.5 no.2
• /
• pp.49-60
• /
• 2005

In this paper, an efficient performance enhancement scheme for an adaptive antenna array under the flat and the frequency-selective Rayleigh fadings is proposed. The proposed signal enhancement scheme is the modified linear signal estimator which combines the rank N approximation by reducing noise eigenvalues(RANE) and Toeplitz matrix approximation(TMA) methods into the linear signal estimator. The proposed performance enhancement scheme is performed by not only reducing the noise component from the signal-plus-noise subspace using RANE but also having the theoretical property of noise-free signal using TMA. Consequently, the key idea of the proposed performance enhancement scheme is to greatly enhance the performance of an adaptive antenna array by removing all undesired noise effects from the post-correlation received signal. The proposed performance enhancement scheme applies at the Wiener maximal ratio combining(MRC) method which has been widely used as the conventional adaptive antenna array. It is shown through several simulation results that the performance of an adaptive antenna array using the proposed signal enhancement scheme is much superior to that of a system using the conventional method under several environments, i.e., a flat Rayleigh fading, a fast frequency-selective Rayleigh fading, a perfect/imperfect power control, a single cell, and a multicell.

• Progress in Superconductivity
• /
• v.9 no.1
• /
• pp.45-49
• /
• 2007

We have investigated the optimum combination of the environmental noise condition and type of SQUID pickup coil in order to obtain maximum signal-to-noise ratio (SNR). The measurement probe consists of 1st order gradiometer with pickup coils of 100 mm, 70 mm, and 50 mm baseline length, a 2nd order gradiometer with 50 mm baseline, and a magnetometer. The pickup coils are fabricated by winding Nb wire on a bobbin with 200 mm diameter. Noise and heart signal of a healthy male were measured by various SQUID sensors with different types of pickup coils in various magnetically shielded rooms (MSR), and compared to each other. The shielding factors were found to be 43 dB, 35 dB and 25 dB at 0.1 Hz for MSR-AS, MSR-BS, MSR-CS, respectively. White noises were $3.5\;fT/Hz^{1/2}$, $4.5\;fT/Hz^{1/2}$ and $3\;fT/Hz^{1/2}$ for the 1st order gradiometers, the 2nd order gradiometers, and magnetometer for all MSRs. SNR of the magnetometer was up to 56 dB in MSR-AS, while the 1st order axial gradiometer with 70 mm baseline length was up to 54 dB in MSR-BS. The 2nd order axial gradiometer with 50 mm baseline length of pickup coil was found to be up to 40 dB in MSR-CS.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.2
• /
• pp.281-287
• /
• 1997

In the conventional inverse modeling method for on-line modeling of the secondary path transfer function, the signal to noise ratio between the arbitrary random signal and the plant noise have to keep at -10 - -20 dB. For these reasons, the modeling can't be exactly implemented by the conventional method alone and the convergence time for modeling becomes too long. In this study, by combining the conventional inverse modeling method with an adaptive line enhancer, or with an adaptive noise canceller, a rigorous transfer functions of secondary path modeling and the control of a primary noise have been implemented simultaneously.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.7 no.4
• /
• pp.167-172
• /
• 1982

We have studied and discussed the error rate performance of Quadrature Amplitude Modulation(QAM) in an environment of cochannel QAM interference and impulsive noise. A general equation of error probability for L-level QAM signal has been derived and the error rate of the 16-QAM signal, as an example, has been calculated as functions of carrier-to-noise power ratio(CNR), carrier-to-interferer power ratio(CIR), impulsive indes, and the phase difference between signal and interferer.

• Journal of Communications and Networks
• /
• v.14 no.3
• /
• pp.243-251
• /
• 2012

Under the power-based capture model, a transmission is successfully received at the destination, even in the presence of other transmissions and background noise, if the received signal-to-interference-plus-noise ratio exceeds a capture threshold. We evaluate the spectral efficiency of simple multi-user channels by combining the basic capture model with a communication-theoretic model. The result is a more refined capture model that incorporates key system design parameters (such as achievable bit rate, target bit error rate, channel bandwidth, and modulation signal constellations) that are absent from the basic capture model. The relationships among these parameters can serve as a tool for optimizing the network performance.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.3
• /
• pp.395-403
• /
• 2014

This paper presents a new approach to improve the signal to noise ratio (SNR) for local seismic disaster preventing system in densely populated area. The seismic data measured in the local site includes various sensing noises (offset or measurement noise) and man-made/natural noises (road and rail traffic noise, rotating or hammering machinery noise, human activity noise such as walking and running, wind/atmospheric pressure-generated noise, etc.). These additive noises are different in time and frequency characters. The proposed method uses 3-stages processing to reduce these different additive noises. In the first stage, misalignment offset noise are diminished by time average processing, and then the second and third stages, coherent/incoherent noises such as man-made/natural noises are suppressed by array stacking. In addition, we derived the theoretical equation of the SNR gain improved by the proposed method. To evaluate the performance of the proposed method, computer simulations were performed with real seismic data and test equipment generated data as the input.