• Transactions of the Korean Society of Mechanical Engineers B
• /
• 제28권5호
• /
• pp.612-618
• /
• 2004

Stereoscopic PIV measurements were made in the wind tunnel with the actual size waterjet model. The main wind tunnel provides the vehicle velocity while the secondary wind tunnel adjusts the jet issuing velocity. Experiments were performed at the range of jet to vehicle velocity ratio (JVR), 3.75 to 8.0 and the Reynolds number of 220,000 based on the jet velocity and the hydraulic diameter of the waterjet intake duct. Wall pressure distributions were measured for various JVRs. Three dimensional velocity fields were obtained at the inlet and outlet of the intake duct. It is found that severe acceleration is occurred at the lip region while deceleration is noticeable at the ramp side. The detailed three dimensional velocity fields can be used as the accurate velocity input for the CFD simulation. It is interesting to note that there are many different types of vortices in the instantaneous velocity field. It can be considered that those vortices are generated by the corner of rectangular section of the intake and Gortler vortices due to the curved wall. However, typical secondary flow with a pair of counter rotating vortex pair is clearly seen in the ensemble averaged velocity field.

• Journal of the Society of Naval Architects of Korea
• /
• 제44권6호
• /
• pp.627-634
• /
• 2007

A bonded plate or a coated part can be debonded by external impact or thermal expansion. To analyse adhesive strength, the blister test is generally adopted. In this paper, a blister test is modelled theoretically and then the stability and bifurcation of the blister are studied under several different cases. The blister is simplified to consist of a pure bending plate attached elastically to the rigid substrate. Expression of the energy release rate is obtained as a form of an explicit function for a circular-type blister or tunnel-type blister grown by controlling the internal pressure or internal volume. Stability and bifurcation are also studied in the frame of the quasi-static evolution. The study shows that the circular- type blister propagates with the first mode of bifurcation and that the tunnel-type blister propagates with a regular wave. It is proved that the waves have the same form on two side lines of the tunnel and that the wave length can be obtained. When the internal pressure is controlled, the blister is unstable, but when the internal volume is controlled, it is stable.

• Journal of the Korean Geosynthetics Society
• /
• 제17권1호
• /
• pp.111-118
• /
• 2018

In case of excavation of the tunnel under weak ground conditions, such as fault zone, leg pile reinforcement with the purpose of suppressing tunnel crown settlement and side wall displacement is commonly applied. There are convergence, crown settlement, leg settlement, and the axial force of leg as a main factor for confirming the safety of support considering the installation angle and length of leg pile reinforcement according to the increase in rate of change of tunnel cross-section. In particular, the influence of right corner settlement, among variables for safety confirmation during excavation, has been analyzed as the dominant factor in the most important priority management showing larger displacement tendency than the increase in rate of the cross-section. And, it was analyzed that the occurrence tendency of axial force on leg pile reinforcement showed the influence of behavior according to the friction support concept mechanism of the pile reinforcement rather than the increase in rate of tunnel cross-section, as it showed a small increase compared to the increase rate of the tunnel cross-section which did not show a great correlation from the viewpoint of the change of the axial force by the length of each leg pile reinforcement with regards to the change in rate of increase in tunnel cross-section. If a certain length of the leg pile reinforcement is selected based on the above grounds, even if the cross-section of the tunnel in poor ground condition is somewhat larger, it has been proved to be a more reasonable method considering the workability and economical efficiency by not extending the length of the leg pile reinforcement by force.

• Tunnel and Underground Space
• /
• 제28권5호
• /
• pp.442-456
• /
• 2018

Scaled model tests were performed to evaluate the reinforcement effect of rock bolts in anisotropic rock mass. For this purpose, two tunnel cases were experimented which had different tunnel sizes, rock strengths, anisotropic angles and coefficients of lateral pressure. The fully grouted rock bolts of the D25 deformed bar were modeled as the basting pins with bead and were systematically installed at the roof and the side wall of the model tunnel. As results of the first case experimentations, the unsupported model showed initial crack at the roof of tunnel, but the supported model with rock bolts showed initial crack at the floor of tunnel where rock bolts were not installed. The crack initiating pressure and the maximum pressure of the supported model with rock bolts were 11% and 7% larger than those of the unsupported model, respectively. Moreover, the effect of the existing discontinuities in anisotropic rock mass on the fracture behavior of tunnel was reduced in the supported model, and so the reinforcement effect of rock bolt turned out to be experimentally verified. As results of the second case experimentations considering different support patterns, the crack initiating pressures of models were larger and the reduction ratios of tunnel area according to applied load were smaller as the length and the quantity of rock bolts were larger. Therefore, it was found that the performance of the rock bolts turned out to be improved as they were larger.

• Journal of Korean Tunnelling and Underground Space Association
• /
• 제19권5호
• /
• pp.761-778
• /
• 2017

The need of the underground space for the infrastructures in urban area is increasing, and especially the demand for shallow tunnels increased drastically. It is very important that the shallow tunnel in the urban area should fulfill not only its own safety conditions but also the safety condition for the adjacent structures and the surrounding sub-structure. Most of the studies on the behavior of shallow tunnels concentrated only on their behaviors due to the local deformation of the tunnel, such as tunnel crown or tunnel sidewall. However, few studies have been performed for the behavior of the shallow tunnel due to the deformation of the entire tunnel. Therefore, in this study the behavior of the surrounding ground and the stability caused by deformation of the whole tunnel were studied. For that purpose, model tests were performed for the various ground surface slopes and the cover depth of the tunnel. The model tunnel (width 300 mm, height 200 mm) could be simulationally deformed in the vertical and horizontal direction. The model ground was built by using carbon rods of three types (4 mm, 6 mm, 8 mm), in various surface slopes and cover depth of the tunnel. The subsidence of ground surface, the load on the tunnel crown and the sidewall, and the transferred load near tunnel were measured. As results, the ground surface subsided above the tunnel, and its amount decreased as the distance from the tunnel increased. The influence of a tunnel ceased in a certain distance from the tunnel. At the inclined ground surface, the wider subsidence has been occurred. The loads on the crown and the sidewall were clearly visible, but there was no effect of the surface slope at a certain depth. The load transfer on the adjacent ground was larger when the cover depth (on the horizontal surface) was lager. The higher the level (on the inclined surface), the wider and smaller it appeared. On the shallow tunnel under inclined surface, the transfer of the ambient load on the tunnel sidewall (low side) was clearly visible.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2006년 제4회 한국유체공학학술대회 논문집
• /
• pp.263-264
• /
• 2006

In this study, the threshold wind speed that causes physical damage on Kiwi fruit plant was investigated through wind tunnel experiments. Total 30 samples of Kiwi fruit branches were tested. On average, the wind speeds for tearing leaves and breaking side branch from the main branch were about 20m/s and 21.7m/s, respectively. For the cases of broken branches, the average length and diameter of the branches were 587.5mm and 7.2mm, respectively. The discoloration and dehydration of Kiwi plant were also observed by photographing leaves and branches after 24 hour later of the wind damage. In addition, the shelter effect of porous wind fences which have been used at agricultural districts was examined with varying several parameters.

• Journal of the Semiconductor & Display Technology
• /
• 제5권1호
• /
• pp.17-20
• /
• 2006

This paper presents of a new type of memory cell that could potentially replace both DRAM and flash memory. The proposed device cell operates by sensing the state of about 1,000 electrons trapped between unique insulating barriers in the channel region of the upper transistor. These electrons are controlled by a side gate on the transistor, and their state in turn controls the gate of the larger transistor, providing signal gain within the memory cell. It becomes faster and more reliable memory with lower operation voltage. Moreover, the use of a multiple tunnel junction (MTJ) fur the vertical transistor can significantly improve the data retention and operation speed.

• Proceedings of the KSR Conference
• /
• 한국철도학회 2010년도 춘계학술대회 논문집
• /
• pp.1000-1005
• /
• 2010

Ride comfort is an important factor for the development of a high-speed train. The aerodynamic force to a high speed train inside tunnels increases the car-body vibration and makes its ride comfort worse. In this study, the aerodynamic force is estimated through a CFD analysis using ADINA, and its car-body vibration and ride comfort are calculated for the aerodynamic force which acts on the side of the train. The numerical results show that the vibration is a lateral mode of the car-body and decreases the ride comfort. On the basis of this numerical simulation, more accurate simulation is necessary for the shape of tunnel and the lateral suspension system of a high speed train.

• Journal of Korean Society for Atmospheric Environment
• /
• 제11권2호
• /
• pp.145-152
• /
• 1995

Predictability of a Gaussian model, ISCST2 was assessed by scaling up wind tunnel experiments with a 1/3,000 terrain model to the real scale. Concentration profiles obtained from the flat-terrain experiment in the neutral condition were estimated to be in agreement with the calculated ones from ISCST2 in the stability class A, but the difference between the two was still large. Concentration profiles from the mountainous-terrain experiments were better fitted to the calculated ones primarily because in the experiment, concentration behind the source was raised due to the effect of a hill in the upstream side. Model prediction was improved with including the downwash effect of buildings and the hill, but overall concentration profiles were not much different from a typical Gaussian profile. While concentration profiles in the experiments were changed with local flows by varying the wind direction and the topography, those from the Gaussian modeling were mot freely changed together with these variations.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 한국추진공학회 2010년도 제35회 추계학술대회논문집
• /
• pp.463-466
• /
• 2010

A scramjet engine intake model was tested with a storage air heater type hypersonic wind tunnel. In test results, there is no large performance change with the variation of the sidewall configurations. In the isolator performance analysis, pressure distribution of oblique shock train and normal shock train was observed. Unstart limit of the model was also confirmed.