• The Korean Journal of Pain
• /
• v.27 no.2
• /
• pp.162-167
• /
• 2014

Background: Although a physician may be the nearest to the radiation source during C-arm fluoroscope-guided interventions, the radiographer is also near the fluoroscope. We prospectively investigated the radiation exposure of radiographers relative to their location. Methods: The effective dose (ED) was measured with a digital dosimeter on the radiographers' left chest and the side of the table. We observed the location of the radiographers in each procedure related to the mobile support structure of the fluoroscope (Groups A, M and P). Data about age, height, weight, sex, exposure time, radiation absorbed dose (RAD), and the ED at the radiographer's chest and the side of the table was collected. Results: There were 51 cases for Group A, 116 cases for Group M and 144 cases for Group P. No significant differences were noted in the demographic data such as age, height, weight, and male to female ratio, and exposure time, RAD and ED at the side of the table. Group P had the lowest ED ($0.5{\pm}0.8{\mu}Sv$) of all the groups (Group A, $1.6{\pm}2.3{\mu}Sv$; Group M, $1.3{\pm}1.9{\mu}Sv$; P < 0.001). The ED ratio (ED on the radiographer's chest/ED at the side of the table) of Group A was the highest, and the ED radio of Group P was the lowest of all the groups (Group A, $12.2{\pm}21.5%$; Group M, $5.7{\pm}6.5%$; Group P, $2.5{\pm}6.7%$; P < 0.001). Conclusions: Radiographers can easily reduce their radiation exposure by changing their position. Two steps behind the mobile support structure can effectively decrease the exposure of radiographers by about 80%.

• Journal of Advanced Navigation Technology
• /
• v.25 no.5
• /
• pp.384-389
• /
• 2021

An optimal ground station (GS) antenna pattern design method for network-based UAV command and control communication systems considering complexity and performance is presented. The GS antenna consists of multiple side sectors and one upward sector. The antenna gain for each vertical/horizontal angle of the GS antenna according to the change of antenna design parameters such as the number of sectors, horizontal and vertical beam-width, and tilt-angle is modeled, and the effect of the parameter changes on the signal-to-noise ratio (SNR) distribution in the virtual three-dimensional space is analyzed. It is observed that the tilt-angle of the side sectors has the greatest effect on the performance, and the longer the distance between GSs, the higher the maximum altitude and the smaller the number of side sectors, the tilt-angle should be lower. In addition, it is observed that the wider vertical beam-width of the side sector is advantageous in maximizing the lowest SNR, but narrow vertical beam-width is advantageous in maximizing the average SNR.

• Archives of Craniofacial Surgery
• /
• v.22 no.2
• /
• pp.85-92
• /
• 2021

Background: Patients with secondary deformities associated with unilateral cleft lip and nose might also suffer from nostril stenosis due to a lack of tissue volume in the nostril on the cleft side. Here, we used full-thickness skin grafts (FTSGs) to reduce nostril stenosis and various methods for skin volume augmentation. We compared the changes in the symmetry of both nostrils before and after surgery. Methods: From February 2016 to January 2020, 34 patients underwent secondary cheiloplasty and open rhinoplasty for secondary deformities of the unilateral cleft lip and nose with nostril stenosis. FTSG was used on the nostril floor, nasal columella, and alar inner lining. The measured nasal profile included the nostril surface, nostril circumference, width of the nostril floor, and distance from the alar-facial groove to the nasal tip. The "overlap area," which was defined as the largest overlapping area when the image of the cleft nostril was flipped to the left and right and overlaid on the image of the normal side nostril, was also calculated. The degree of symmetry was evaluated by dividing the value of the cleft side by that of the normal side of each measured profile and expressed as "ratios." Results: The results of all profile ratios, except for the nostril floor width, became significantly close to 1, which represents full symmetry. The overlap area ratio improved from 62.7% to 77.3%, meaning that the length and width of the nostril as well as the overall shape became similar (p< 0.05). Conclusion: When performing cleft rhinoplasty with nostril stenosis, FTSG is useful to achieve symmetry in the nostril size and shape. Skin grafting is simpler to perform than the other types of local flap, and the results are generally satisfactory.

• Clinics in Shoulder and Elbow
• /
• v.22 no.3
• /
• pp.139-145
• /
• 2019

Background: The present study was undertaken to evaluate the relationship between location of the rotator cuff tear and shape of the subacromial spur. Methods: Totally, 80 consecutive patients who underwent arthroscopic repair for partial thickness rotator cuff tear were enrolled for the study. Bigliani's type of the acromion, type of subacromial spur, and location of partial thickness tear of the rotator cuff were evaluated using plain X-ray and magnetic resonance imaging. We then compared the groups of no spur with spur, and heel with traction spur. Results: Of the 80 cases, 25 cases comprised the no spur group, and 55 cases comprised the spur group. There was a significant difference in type of tear (p=0.0004) between these two groups. Bursal side tears were significantly greater (odds ratio=6.000, p=0.0007) in the spur group. Subjects belonging to the spur group were further divided into heel (38 cases) and traction spur (17 cases). Comparing these two groups revealed significant differences only in the type of tear (p=0.0001). Furthermore, the heel spur had significantly greater bursal side tear (odds ratio=29.521, p=0.0005) as compared to traction spur. Conclusions: The heel spur is more associated to bursal side tear than the traction spur, whereas the traction spur associates greater to the articular side tear.

• Structural Engineering and Mechanics
• /
• v.83 no.4
• /
• pp.415-433
• /
• 2022

Eighteen (18) (120×300×2200 mm) beams were prepared and tested to evaluate the shear strength of Glass Fiber Reinforced Concrete (GFRC) beams with no shear reinforcement, and evaluate the effectiveness of various innovative strengthening systems to increase the shear capacity of the GFRC beams. The test variables are the amount of discrete glass fiber (0.0, 0.6, and 1.2% by volume of concrete) and the type of longitudinal reinforcement bars (steel or GFRP), the strengthening systems (externally bonded (EB) sheet, side near-surface mounted (SNSM) bars, or the two together), strengthening material (GFRP or steel) links, different configurations of NSM GFRP bars (side bonded links, full wrapped stirrups, side C-shaped stirrups, and side bent bars), link spacing, link inclination angle, and the number of bent bars. The experimental results showed that adding the discrete glass fiber to the concrete by 0.6%, and 1.2% enhanced the shear strength by 18.5% and 28%, respectively in addition to enhancing the ductility. The results testified the efficiency of different strengthening systems, where it is enhanced the shear capacity by a ratio of 28.4% to 120%, and that is a significant improvement. Providing SNSM bent bars with strips as a new strengthening technique exhibited better shear performance in terms of crack propagation, and improved shear capacity and ductility compared to other strengthening techniques. Based on the experimental shear behavior, an analytical study, which allows the estimation of the shear capacity of the strengthened beams, was proposed, the results of the experimental and analytical study were comparable by a ratio of 0.91 to 1.15.

• Geomechanics and Engineering
• /
• v.34 no.2
• /
• pp.115-124
• /
• 2023

By conducting three-dimensional simulation with consideration of small-strain characteristics of soil stiffness, the effects of excavation geometry and tunnel cover to diameter ratio on deformation mechanisms of an existing tunnel located either at a side of basement or directly underneath the basement were systematically studied. Field measurements were used to verify the numerical model and model parameters. For basement excavated at a side of an existing tunnel, the maximum settlement and horizontal displacement of the tunnel are always observed at the tunnel springline closer to basement and tunnel crown, respectively, regardless of basement geometry. By increasing basement length and width by five times, the maximum movements of tunnel located at the side of basement and directly underneath the basement increase by 450% and 186%, respectively. Obviously, tunnel movements are more sensitive to basement length rather than basement width. For basement excavated at a side of an existing tunnel, tunnel movements at basement centerline become stable when basement length reaches 10 H_e (i.e., final excavation depth). Moreover, tunnel heaves due to overlying basement excavation become stable when the normalized basement length (L/H_e) is larger than 8.0. As tunnel cover to diameter ratio varies from 2.5 to 3.0, the maximum heave and tensile strain of tunnel due to overlying basement excavation decrease by up to 41.0% and 44.5%, respectively. If basement length is less than 8 H_e, the assumption of plane strain condition of basement-tunnel interaction grossly overestimates tunnel movements, and ignores tensile strain of tunnel along its longitudinal direction. Thus, three-dimensional numerical analyses are required to obtain a reasonable estimation of tunnel responses due to adjacent and overlying basement excavations in clay.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.3
• /
• pp.184-196
• /
• 2020

In this paper, a single-bit 2nd-order delta-sigma modulator with the architecture of cascaded-of-integrator feedforward (CIFF) is proposed for precision measurement of current flowing through a secondary cell battery in a battery management system (BMS). The proposed modulator implements two switched capacitor integrators and a single-bit comparator with peripheral circuits such as a non-overlapping clock generator and a bias circuit. The proposed structure is designed to be applied to low-side current sensing method with low common mode input voltage. Using the low-side current measurement method has the advantage of reducing the burden on the circuit design. In addition, the ±30mV input voltage is resolved by the ADC with 15-bit resolution, eliminating the need for an additional programmable gain amplifier (PGA). The proposed a single-bit 2nd-order delta-sigma modulator has been implemented in a 350-nm CMOS process. It achieves 95.46-dB signal-to-noise-and-distortion ratio (SNDR), 96.01-dB spurious-free dynamic range (SFDR), and 15.56-bit effective-number-of-bits (ENOB) with an oversampling ratio (OSR) of 400 for 5-kHz bandwidth. The area and power consumption of the delta-sigma modulator are 670×490 ㎛2 and 414 ㎼, respectively.

• Journal of Cadastre & Land InformatiX
• /
• v.48 no.2
• /
• pp.121-135
• /
• 2018

The ministry of land, Infrastructure and transport has revised the "National Land Planning and Utilization Act" in 2012. As a result, the regulation of floor area ratio for land covering two or more zoning area has been changed. This study conducted an analysis of the policy effects of changes in the criteria for the application of the floor area ratio by revising the "National Land Planning and Utilization Act". Land covering two or more zoning area means a street side commercial area and street side residential area that is generally understood. This study analyzed the policy effects in Gangnam-gu which has relatively large areas of street side commercial area and street side residential area. The 468 office building transaction cases were analyzed in Gangnam-gu from 2007 to 2017. The result shows that the office building, which has received incentive for policy changes, reported a 19.08% rise in price compared to the one that did not. It means that the economic effects of change of application standard were significant. The existing policy also served as a restriction on land use by landowners, which in turn contributed to the devaluation of the asset's intrinsic value. Therefore, this study may have contributed to the rational use of land and to provide an empirical basis for the change in policy to be assessed for its intrinsic value.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.1
• /
• pp.44-51
• /
• 2000

We have analyzed optical matched filters considering the third order signals in the optical code division multiple access (CDMA) system based on optical series coupler access encoder (SCAE) and series coupler access decoder (SCAD). In previous studies, the performance evaluation of the optical CDMA system using SCAE and SCAD was not sufficiently accurate because they analyzed system performance only considering the first order signals. Since optical SCAE and SCAD intrinsically have high order signals of various patterns as the number of coupler increases, they change auto- and cross-correlation intensities. Thus, it is necessary to investigate properties of the third order signals so that we may analyze the exact performance of system. In this paper, we mathematically interpret the optical signals up to the third order, and analyzed the effects of th third order signals on auto- and cross-correlation intensities. In result, as ${\alpha}$(coupling coefficient) value increases, the intensity of the third order signals increases. It is found that the peak to side-lobe ratio considering the third order signals is degraded by 3.75 dB at N(coupler number)=5 and ${\alpha}$=0.5. Also if threshold value in receiver is set by main-lobe peak of the first order signals, it is found that the number of users in an optical CDMA system is limited because the intensity peak of side-lobes is raised by the third order signals.

• Journal of the Korean Home Economics Association
• /
• v.26 no.3
• /
• pp.53-68
• /
• 1988

This article concerned with the nutritional status and the taste of the lunch box of 311 middle school girls in Kwangju City from May 18 to June 12 in 1987. The purpose of this research was making materials to show direction of the education about nutrition by checking relationships among the nutritional status for the lunch box, the taste of food and the environmental factors. The results observed in the study were as follows: 1. The intake of nutrition from the lunch box and the ratio between the recommended dietary allowance and the contained nutrients in the lunch box as follows. Calorie(603 Kcal, 78.6%), protein (21.7g, 93.1%) Animal protein (10.3g, 132.1%) calcium (151.7 g, 56.9%) Ferrum 93.1 mg, 51.7%), Vitamin a (129.3 RE, 55.4%) Vitamin B1 (0.29 mg, 72.5%), Vitamin B (0.26 mg, 55.3%) Niacin (4.7 mg, 94.0%), Vitamin C 913.2 mg, 79.0%). Except animal protein, all the recommended dietary allowance. 2. According to the intake of calorie, the ratio of taken carbohydrate, protein and fat was 77.7 : 15.5 : 6.8. The intake of protein was desirable but most of calorie depended on carbohydrate. Among the total intake of protein, the ratio of animal protein was 47.5%, which was a high rate. 3. Most of calorie (75%), was taken from staples, protein (41.5%), vitamin B1 (48.3%) were taken at the same rate from staples and side dishes. Most of fat, calcium, ferrum, vitamin A, vitamin B, and vitamin C, was taken from side dishes. 4. In taking among the five basic food groups, proportion of the grain fourth food group was the highest, light color vegetable the third food groups, proportion of the grain fourth food group was the highest, light color vegetable the third food group was second, and Calcium food the second food group was the lowest. 5. As the staples, students liked tchajangmyon, mandu and ttokkuk as written order. They disliked Kongbap and Patpap. As the side dishes for the lunch box, they liked kimchi, ham, sausage, cuttlefish, dried slices of filefish, eggs and green seaweed as written order. As a side dishes they liked Laver, Cucumber, Squid, lettuce, Potatoes. They disliked pork fat, cow's intestines, cow's liver, Crussian carp, pickled fish. The favorite snack was fruits, ice cream, hamburger, Chocolate and milk. 6. In taking condition of the principal food, rice rate (65.6%) was the most, and mixed food was 5 or 10%. 7. Favorite cooking was frying, roasting and kimch. But disagreeable cooking was pickling. 8. Favorite food was what was pungent but disagreeable food was what was salty. 9. the higher parents educational background was, the higher their income was. Also the more various the information about the nutrition was, the better the intake of nutrition was. 10. The preference tendency influenced in choosing the side dish of the Lunch box. The higher the preference tendency of the girl students became, the better their nutrition condition became.