• Journal of the korean academy of Pediatric Dentistry
• /
• v.28 no.4
• /
• pp.673-682
• /
• 2001

The use of resin composites has continued to increase over the last several years. In spite of their growing popularity, composites continue to exhibit a number of undesirable characteristics. One of the major deficiencies of composite restorative resins is their inadequate resistance to wear. Of the multitude of factors that have been associated with wear, subsurface degradation within the restoration is considered to be one. The aim of this study was to evaluate the resistance to degradation of four commercial composite resins in an alkaline solution. This solution with a high concentration of hydroxyl ions is a convenient medium for accelerated degradation of silane coupling and filler particles. The brands studies were Definite($Degussa-H\ddot{u}ls$ AG, Germany), Prodigy(Kerr, USA), Pyramid(Bisco, USA) and Synergy(Coltene, Swiss). Preweighed discs of each brand were exposed to 0.1N NaOH solution at $60^{\circ}C$. After 14 days they were removed, neutralized with HCl, washed with water and dried. Resistance to degradation was evaluated on the basis of following parameters : (a) mass loss(%)-determined from pre-and post-exposed specimen weights : (b) Si loss(ppm)-obtained from ICP-AE analysis of solution exposed to specimens; and (c) degradation $depth({\mu}m)$-measured microscopically (SEM) from polished circular sections of exposed specimens. The results were follows: 1. Mass loss of Synergy was $1.24{\pm}0.002%$, it was the highest, there was no significant difference among the materials. 2. The degree of degradation layer depth of Synergy was $107.83{\pm}2.52{\mu}m$, it was the highest, there was no significant difference among any other materials than Synergy. 3. There was no difference among the four materials in Si loss. 4. The correlation coefficient between mass loss and degradation depth was relatively high(r=0.06, p<0.05). 5. There was no coefficient correlation between Si loss and mass loss, the degree of degradation layer depth and Si loss. 6. When observed with SEM, destruction of bonding is observed between resin matrix and filler.

• Journal of the Mineralogical Society of Korea
• /
• v.17 no.4
• /
• pp.309-325
• /
• 2004

The Cannington Ag-Pb-Zn deposit, northwest Queensland, Australia developed around the host rocks composing banded and migmatitic gneisses, sillimanite-garnet schist and amphibolite. Three crystal habits of sillimanite, gahnite (Zn-spinel) and garnet porphyroblasts occurred on the host rocks of the Cannington deposit could be used to delineate metamorphism that closely associated with Zn-mineralization in the deposit. Linkages the metamorphism to Zinc-mineralization is determined in four chemical systems, KFMASH (K$_2$O-FeO-MgO-Al$_2$O$_3$-SiO$_2$-$H_2O$), KFMASHTO (K$_2$O-FeO-MgO-Al$_2$O$_3$-SiO$_2$-$H_2O$-TiO$_2$-Fe$_2$O$_3$), NCKFMASH (Na$_2$O-CaO-K$_2$O-FeO-MgO-AlO$_3$-SiO$_2$-$H_2O$) and MnNCK-FMASH (MnO-Na$_2$O-CaO-K$_2$O-FeO-MgO-AlO$_3$-SiO$_2$-$H_2O$), using THERMOCALC program (version 3.1; Powell and Holland 1988). Partial melting in MnNCKFMASH and NCKFMASH systems occurs at lower temperature than in the KFMASH and KFMASHTO systems. The partial melting temperature decreases with increasing of Na/(Na+Ca+K) of the bulk rock compositions in the MnNCKFMASH system. The host rocks have melted ca 15 vol.% in the MnNCKFMASH system at peak metamorphic conditions (634$\pm$62$^{\circ}C$ and 4.8$\pm$1.3 kbar), but partial melting have not occurred in KFMASHTO system. Based on calculations of sillimanite isograd in different systems and sillimanite modal pro-portion, prismatic and rhombic sillimanite and gahnite porphyroblasts including prismatic sillimanite inclusion probably have resulted from pressure and temperature increasing through partial melting (from 550～$600^{\circ}C$, 2.0～3.0 kbar to 700～75$0^{\circ}C$, 5.0～7.0 kbar), furthermore have experienced N-S then W-E crustal shortening during D$_1$ and D$_2$ deformation. Consequently, Zinc mineralization related to gahnite growth occurred during D$_2$ and was redistributed and upgraded by partial melting and retrograde metamorphism into structural and rheological sites during shearing in D$_3$.

• Journal of Korean Society for Atmospheric Environment
• /
• v.34 no.3
• /
• pp.406-417
• /
• 2018

In this study, $PM_{2.5}$ samples were collected during approximately 3 years in Chuncheon, a small residential and tourist city, in Korea. The average $PM_{2.5}$ concentration was $26.9{\mu}g/m^3$, exceeding the annual national air quality standard. $PM_{2.5}$ showed typical seasonal variation, having higher concentration in winter and lower concentration in summer. Sixteen metallic elements in $PM_{2.5}$ were also analyzed, and K was the highest contributor especially in late fall and winter. In addition, K considerably increased for the top 10% of $PM_{2.5}$ samples and showed the highest correlation coefficient with $PM_{2.5}$ among all other metallic elements. These results suggest that the combustion of agricultural residue and other biomass, the major source of K was likely to be important to high $PM_{2.5}$ concentration events in this city. Crustal elements including Al, Fe, Si, Ti, Mg showed high concentration in spring while Cr, Cu and Ni were relatively consistent throughout a year. Principal component analysis was used to trace the sources, and soil re-suspension, combustion of biomass and fossil fuels, and asphalt concrete production were identified as the main sources of $PM_{2.5}$.

• Advances in materials Research
• /
• v.5 no.1
• /
• pp.55-66
• /
• 2016

This paper describes a study on the effects of $Mg_2Si_{(p)}$ addition on the microstructure, porosity, and mechanical properties namely hardness and tensile properties of AA332 composite. Each composite respectively contains 5, 10, 15, and 20 wt% reinforcement particles developed by a stir-casting. The molten composite was stirred at 600 rpm and melted at $900^{\circ}C{\pm}5^{\circ}C$. The $Mg_2Si$ particles were wrapped in an aluminum foil to keep them from burning when melting. The findings revealed that the microstructure of $Mg_2Si_{(p)}/AA332$ consists of ${\alpha}$-Al, binary eutectic ($Al+Mg_2Si$), $Mg_2Si$ particles, and intermetallic compound. The intermetallic compound was identified as Fe-rich and Cu-rich, formed as polygonal or blocky, Chinese script, needle-like, and polyhendrons or "skeleton like". The porosity of $Mg_2Si_{(p)}/AA332$ composite increased from 8-10% and the density decreased from 9-12% from as-cast. Mechanical properties such as hardness increased for over 42% from as-cast and the highest UTS, elongation, and maximum Q.I were achieved in the sample of 10% $Mg_2Si$. The study concludes that combined with AA332, the amount of 10 wt% of$Mg_2Si$ is a suitable reinforcement quantity with the combination ofAA332.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.254.2-254.2
• /
• 2014

The Transmission Fourier Transform Infrared spectroscopy (FTIR) of SiOx charge storage layer with the richest silicon content showed an assignment at peaks around 2000~2300 cm-1. It indicated that the existence of many silicon phases and defect sources in the matrix of the SiOx films. The total hysteresis width is the sum of the flat band voltage shift (${\Delta}VFB$) due to electron and hole charging. At the range voltage sweep of ${\pm}15V$, the ${\Delta}VFB$ values increase of 0.57 V, 1.71 V, and 13.56 V with 1/2, 2/1, and 6/1 samples, respectively. When we increase the gas ratio of SiH4/N2O, a lot of defects appeared in charge storage layer, more electrons and holes are charged and the memory window also increases. The best retention are obtained at sample with the ratio SiH4/N2O=6/1 with 82.31% (3.49V) after 103s and 70.75% after 10 years. The high charge storage in 6/1 device could arise from the large amount of silicon phases and defect sources in the storage material with SiOx material. Therefore, in the programming/erasing (P/E) process, the Si-rich SiOx charge-trapping layer with SiH4/N2O gas flow ratio=6/1 easily grasps electrons and holds them, and hence, increases the P/E speed and the memory window. This is very useful for a trapping layer, especially in the low-voltage operation of non-volatile memory devices.

• Journal of Information Technology and Architecture
• /
• v.9 no.4
• /
• pp.423-432
• /
• 2012

EA (Enterprise Architecture) is an SI (System Integration) approach, i.e., a comprehensive plan for SI, which shows the elements of SI and the relationships among them. Since EA can be utilized in every stages of SI, the more large-scaled and complicated SI projects are, the more important EA is. Although many central government agencies and wide local governments implemented EA, the current level of EA utilization is still low. One of the reasons is the low level of EA updating. Some reasons of the low level of EA updating are the low frequency of EA updating, and the shortage of workers, as well. In order to improve the frequency of EA updating and alleviate the workloads of SI officers, MLTM (Ministry of land, transport, and maritime affairs) standardized the processes and documents for SI projects, and implemented PMS (Project Management System) that can support the unifying management of SI projects and be connected with EA system. We expect that EA information are updated efficiently, the level of EA utilization is boosted, and the qualities of SI products are improved, by the implementation of the PMS connected with EA system.

• Korean Journal of Environment and Ecology
• /
• v.26 no.1
• /
• pp.67-73
• /
• 2012

This study has compared the different types of forest fire sites and the unburned site at Samcheuk-si Gangwon-do by assessing the amount of litter production, nutrient concentration returned to forest floor from July 2007 through October 2010. The research showed that the average amounts of litterfall produced in the unburned site, the crown fire site(C-1), the crown fire site(C-3) and the ground fire site(G-2) were $7.74{\pm}2.56$, $1.17{\pm}0.67$, $2.97{\pm}0.44$ and $2.92{\pm}0.42ton{\cdot}ha^{-1}{\cdot}yr^{-1}$, respectively. In the unburned site, the average amounts of total nitogen(T-N), total phosphorus(T-P), potassium(K), calcium(Ca) and magnesium(Mg) returned to the forest floor were $22.20{\pm}12.43$, $1.16{\pm}0.46$, $2.68{\pm}1.44$, $16.22{\pm}4.69$ and $1.36{\pm}0.32 kg{\cdot}ha^{-1}{\cdot}yr^{-1}$, respectively whereas those in the crown fire site(C-1) were $3.73{\pm}2.31$, $0.10{\pm}0.09$, $0.27{\pm}0.20$, $2.75{\pm}2.58$ and $0.24{\pm}0.27 kg{\cdot}ha^{-1}{\cdot}yr^{-1}$, respectively. This study showed that the nutrient content returned to forest floor was higher in the following order: unburned site(Un) > crown fire site(C-3) > ground fire site(G-2) > crown fire site(C-1).

• Korean Journal of Ichthyology
• /
• v.24 no.2
• /
• pp.94-100
• /
• 2012

The spine loach, Cobitis hankugensis endemic to Korea were collected at the Nokdong River, Unbong-eup, Namwon-si, Jeollabuk-do during June 2007 for study its eggs development and early life history. The eggs were obtained by injecting gonadotropin (LHRH-1) to female and were fertilized by dry method in the laboratory condition. The matured eggs were separative, demersal and light yellowish with $1.29{\pm}0.07mm$ in diameter average. Under $23{\sim}25^{\circ}C$, the eggs were hatched in 45~52 hours after fertilization, and just hatching larvae were $4.5{\pm}0.24mm$ in total length. On 5 days after hatching, they were $6.6{\pm}0.13mm$ in total length and their yolk sacs were completely absorbed. From 25 days after hatching, they became the juvenile stage with $9.0{\pm}0.49mm$ in total length. On the 100 days after hatching, their external forms and band patterns were similar to those of adults with average $27.3{\pm}2.82mm$ in total length.

• Journal of Powder Materials
• /
• v.24 no.5
• /
• pp.400-405
• /
• 2017

The addition of a large amount of alloying elements reduces the compactibility and increases the compacting pressure, thereby shortening the life of the compacting die and increasing the process cost of commercial PM steel. In this study, the characteristic changes of Fe-Mo-P, Fe-Mn-P, and Fe-Mo-Mn-P alloys are investigated according to the Si contents to replace the expensive elements, such as Ni. All compacts with different Si contents are fabricated with the same green densities of 7.0 and $7.2g/cm^3$. The transverse rupture strength (TRS) and sintered density are measured using the specimens obtained through the sintering process. The sintered density tends to decrease, whereas the TRS increases as the Si content increases. The TRS of the sintered specimen compacted with $7.2g/cm^3$ is twice as high as that compacted with $7.0g/cm^3$.

• Proceedings of the Korean Environmental Health Society Conference
• /
• 2004.06a
• /
• pp.142-145
• /
• 2004

The purpose of this study was to characterize background mass concentration of fine particle PM10 and metallic composition from September 2001 to August 2002 in comparison with a medium-sized city, Asan and a metropolitan city, Seoul. Annual mean PM10 concentrations in Asan and Seoul were 47.98 and $75.33\;{\mu}g\;/\;m^3$, respectively. The concentrations of PM10 were highest in spring season in both cities. The concentrations of measured metals except As and Pb in Asan were higher than those in Seoul. Yellow dust could affect the mass and metals concentrations of measured PM10 in Asan and Seoul. Relationship between measured metals concentrations showed that Si and Fe were associated with natural sources such as soil. Pb, Cu and Zn were closely related to urban anthropogenic sources such as fuel combustion. Especially, relationship between metals showed different association during yellow dust. Proper management for fine particles is warranted in Asan, considering the concentrations of metallic elements in fine particles in Asan were relatively higher than those in Seoul.