• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.11-11
• /
• 2008

ZnO has a very large exciton binding energy (60 meV) as well as thermal and chemical stability, which are expected to allow efficient excitonic emission, even at room temperature. ZnO based electronic devices have attracted increasing interest as the backplanes for applications in the next-generation displays, such as active-matrix liquid crystal displays (AMLCDs) and active-matrix organic light emitting diodes (AMOLEDs), and in solid state lighting systems as a substitution for GaN based light emitting diodes (LEDs). Most of these electronic devices employ the electrical behavior of n-type semiconducting active oxides due to the difficulty in obtaining a p-type film with long-term stability and high performance. p-type ZnO films can be produced by substituting group V elements (N, P, and As) for the O sites or group I elements (Li, Na, and K) for Zn sites. However, the achievement of p-type ZnO is a difficult task due to self-compensation induced from intrinsic donor defects, such as O vacancies (Vo) and Zn interstitials ($Zn_i$), or an unintentional extrinsic donor such as H. Phosphorus (P) doped ZnO thin films were grown on c-sapphire substrates by radio frequency magnetron sputtering with various Ar/ $O_2$ gas ratios. Control of the electrical types in the P-doped ZnO films was achieved by varying the gas ratio with out post-annealing. The P-doped ZnO films grown at a Ar/ $O_2$ ratio of 3/1 showed p-type conductivity with a hole concentration and hole mobility of $10^{-17}cm^{-3}$ and $2.5cm^2/V{\cdot}s$, respectively. X-ray diffraction showed that the ZnO (0002) peak shifted to lower angle due to the positioning of $p^{3-}$ ions with a smaller ionic radius in the $O^{2-}$ sites. This indicates that a p-type mechanism was due to the substitutional Po. The low-temperature photoluminescence of the p-type ZnO films showed p-type related neutral acceptor-bound exciton emission. The p-ZnO/n-Si heterojunction LEO showed typical rectification behavior, which confirmed the p-type characteristics of the ZnO films in the as-deposited status, despite the deep-level related electroluminescence emission.

• The Korean Journal of Ecology
• /
• v.24 no.2
• /
• pp.101-109
• /
• 2001

We created an environmental forest on the basis of ecological design around the incineration plant of Jindo Engineering and Construction Co., Ltd., which is located in Jeongwang-dong, Siheung-si, Kyunggi-do. To get ecological information of this site, physico-chemical properties of soil on salt marsh, which is located close to the syudy site and of forest soil transported from other sites for ecological restoration were analyzed. Texture of salt marsh and transported soils were loam and sandy loam, respectively. pH, organic matter, T-N, available P, and exchangeable K and Na contents of salt marsh and transported forest soils were 6.7 and 5.4, 4.1 and 0.4%, 1.0 and 0.3mg/g, 46.7 and 6.8ppm, 521 and 207ppm, and 3.8 and 0.5mg/g, respectively. Introduced plants were selected among the dominant species of forests and the species composing the potential natural vegetation around the present study site. Those plants were selected again by considering the tolerances to air pollution and to salt, and their availability. Selected trees were Pinus thunbergii, Sophora japonica, Celtis sinensis, Quercus aliena, Q. serrata, Q. dentata, and Q. acutissima. Selected sub-trees were Albizzia julibrissin, Koelreuteria poniculata, and Styrax japonica and shrubs were Rhododendron yedoense var. poukhanense, R. mucronulatum, Callicarpa japonica, Euonymus alatus, E. japonica, and R. schlippenbachii. On the other hand, introduction of herbs was not considered except for Liriope platyphylla, which was ornamentally planted in one site. Planting bed of mound type was adopted to provide the fine drainage system. Mound was designed to furnish litter, A, B, and C layers simuating the profile of forest soil. Slope of mound was mulched by rice straw of 2cm in thickness to prevent for sliding of litter and soil in cases of strong wind or heavy rain. Height of mound was designed to secure more than 1 m by combining A and B layers. Narrow zones, in which mound with stable slope degree cannot be prepared, was designed to equip the standard soil depth with the introduction of stone for supporting. On the other hand, plants with shallow root system were arranged in some zones, in which satisfactory soil depth cannot be ensured. Plants were arranged in the order of tree, sub-tree, and shrub from center to edge on the mound to make a mature forest of a dome shape in the future. Dispersion of plants was designed to be random pattern rather than clumped one. Problems on creation of the environmental forest by such ecological design were found to be management or inspection by non-specialized project operators and inspecting officers, and regulations for construction without ecological background. Alternative plans to solve such problems were suggested.

• Korean Journal of Ecology and Environment
• /
• v.36 no.1 s.102
• /
• pp.48-56
• /
• 2003

This study was evaluated about the seasonal variations of ecosystem in Nammae Reservoir based on the interrelation of physico-chemical characteristics, nutrients, chlorophyll a, b, c and standing crops of phytoplanktons. The amounts of chlorophyll a, b, c were respectively maximum (295 mg/, 9.5mg/l and 48mg/l) at station 1 in June and the standing crop of phytoplanktons was the highest ($1.7{\time}10^5$ cells/1) at stations 3 in July. The range of temperature was $7{\sim}37.4^{\circ}C$. The maxium of pH was $9.9{\sim}10.1$ at all stations in August, the minimum was 7 in September. SS was maximum (308 mg/1) at station 1 in June, while it was minimum (4 mg/l) at the same station in November. The maximal COD and DOC were 33 mg/1 and 16 mg/1 respectively at station 1 in June. As for phytoplanktons, Microcystis aeruginosa, blue-green alga in July${\sim}$August, Scenedesmus acutus, green alga in March${\sim}$May and November${\sim}$January and Cyclotella orientalis, Diatoms in October were dominant species. The amounts of P and Si were generally high in summer, they were low in autumn and winter. Nammae Reservoir assessed by trophic state index was eutrophicated and overtrophicated. These results indicated that Nammae Reservoir was faced with heavy water pollution. As preceding management for the basin of the Reservoir, it will have to be continually studied for an ecosystem reservation.

• Journal of Animal Environmental Science
• /
• v.8 no.2
• /
• pp.99-106
• /
• 2002

This study was conducted to improve utilization efficiency of slurry and choose a suitable type of tractor power which can be attached by manure spreader in the paddy field. In the paddy field, the pulling force for the spreader was measured by using a measurement system installed between tractors with and without the spreader. The soil moisture contents at the 0${\sim}$10cm and 10${\sim}$20cm depth of test soil(SiCL) were 28.45% d.b. and 23.47% d.b., respectively in average while Cone Index at l0cm and 15cm depth were 14.5kPa and 16.2kPa, respectively. It was impossible to measure the soil moisture contents and Cone Index below 20cm depth of the soil because the hardness of the soil increased greatly. Thereafter, hard pan of the sampled soil was found at 15${\sim}$20cm depth. While the required power only for the dragged tractor was found to be 3.44kW in the test field, the required pulling powers of tractor considering the pumping were 8.48${\sim}$12.48kW, 12.19${\sim}$16.19kW, 16.96${\sim}$20.96kW, respectively for 2 tons, 3 tons, and 4 tons of tank capacity. As the tank capacity increased, the sinkage of soil were also increased to 7cm, l0cm, and 12cm, respectively for the tractors with 2 tons, 3 tons and 4 tons of tank capacity. Considering about 60% of pulling efficiency of tractor, a tractor which had lower than 25.74kW of pulling power was suitable to pull the spreader and spread the slurry simultaneously for manure spreader with 2 tons of tank capacity. 29.42kW${\sim}$36.78kW of pulling power was found to be optimum for the tractor with 3 tons of tank capacity while over 40.45kW for 4 tons of tank capacity.

• Asian Pacific Journal of Cancer Prevention
• /
• v.16 no.9
• /
• pp.3667-3671
• /
• 2015

Invasion and metastasis is the major cause of tumor recurrence, difficulty for cure and low survival rate. Excavating key transcription factors, which can regulate tumor invasion and metastasis, are crucial to the development of therapeutic strategies for cancers. PU.1 is a master hematopoietic transcription factor and a vital regulator in life. Here, we report that, compared to adjacent non-cancerous tissues, expression of PU.1 mRNA in metastatic hepatocellular carcinoma (HCC), but not primary HCC, was significantly down-regulated. In addition, levels of PU.1 mRNA in metastatic hepatoma cell lines MHCC97L and MHCC97H were much lower than in non-metastatic Hep3B cells. Transwell invasion assays after PU.1 siRNA transfection showed that the invasion of hepatoma cell lines was increased markedly by PU.1 knockdown. Oppositely, overexpression of PU.1 suppressed the invasion of these cells. However, knockdown and overexpression of PU.1 did not influence proliferation. Finally, we tried to explore the potential mechanism of PU.1 suppressing hepatoma cell invasion. ChIP-qPCR analysis showed that PU.1 exhibited a high binding capacity with miR-615-5p promoter sequence. Overexpression of PU.1 caused a dramatic increase of pri-, pre- and mature miR-615-5p, as well as a marked decrease of miR-615-5p target gene IGF2. These data indicate that PU.1 inhibits invasion of human HCC through promoting miR-615-5p and suppressing IGF2. These findings improve our understanding of PU.1 regulatory roles and provided a potential target for metastatic HCC diagnosis and therapy.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.18 no.3
• /
• pp.42-51
• /
• 1981

Boron was predeposited into p (100) Si wafer at 94$0^{\circ}C$ for 60minutes to make the back surface field. High tempreature diffusion process at 1145$^{\circ}C$ for 3 hours was immediately followed without removing boron glass to obtain high surface concentration Back boron was annealed at 110$0^{\circ}C$ for 40minutes after boron glass was removed. N+ layer was formed by predepositing with POCI3 source at 90$0^{\circ}C$ for 7~15 minutes and annealed at 80$0^{\circ}C$ for 60min1es under dry Of ambient. The triple metal layers were made by evaporating Ti, Pd, Ag in that order onto front and back of diffused wafer to form the front grid and back electrode respectively. Silver was electroplated on front and back to increase the metal thickness form 1~2$\mu$m to 3~4$\mu$m and the metal electrodes are alloyed in N2 /H2 ambient at 55$0^{\circ}C$ and followed by silicon nitride antireflection film deposition process. Under artificial illumination of 100mW/$\textrm{cm}^2$ fabricated N+PP+ cells showed typically the open circuit voltage of 0.59V and short circuit current of 103 mA with fill factor of 0.80 from the whole cell area of 3.36$\textrm{cm}^2$. These numbers can be used to get the actual total area(active area) conversion efficiency of 14.4%(16.2%) which has been improved from the provious N+P cell with 11% total area efficiency by adding P+ back.

• Economic and Environmental Geology
• /
• v.2 no.1
• /
• pp.1-12
• /
• 1969

In the Sangdong Mine area, Taebaegsan series (Pre-Cambrian) and Chosun System (Cambro-ordovician) are widely distributed. The Chosun System consists of Yangdug Series (Jangsan Quartzite and Myobong Slate) and The Great Limestone Series (Pungchon Limestone, Shesong Shale, Hwajeol Formation and Dongjeom Quartzite). The mineralized zone containing the main ore body of the Sangdong Mine was developed in the Myobong Slate formation. The result of the field and microscopic study on the mineral paragenesis and it's wall rock alteration in the tungsten ore deposit shows the following features. The orogenic movements of the Post-Chosun System in the Hambaeg Geosyncline are closely related to the tungsten ore deposition in the area, the ore minerals are composed mainly of scheelite, powelite molybdenite and sulfide minerals, and gangue minerals are hornblende, diopside, garnet, quartz, phlogopite, tremolite, biotite, muscovite, fluorite, etc., main ore body was enriched by scheelite bearing quartz vein filling into interstices of formerly mineralized zones, and the minor faults, faults of N $60^{\circ}-70^{\circ}W$, $45^{\circ}-60^{\circ}NE$ and joints, which were formed at the end of the mineralization and the slate. Country rock of the ore body was altered into the following several zones from the outside to the inside; lowgrade recrystalline aureole, silicified sericite zone, and diopside-hornblende zone. Under the microscopic observation of 195 samples taken from throughout ore body can be classified into 10 different groups by their mineral paragenesis as shown in table 2. The garnet-diopside group is primary skarn and it shows gradational change to the groups of later stage by the successive processes of metasomatism. From the stage of quartz-bearing group, the dissemination of scheelite is seen. The crystallization of scheelite in the bed started with the quartz deposition and continued to the last stage when quartz vein intruded into the main ore body. In the field and the under ground investigation a durable limestone bed in thickeness about 20 meters and their remnants in ore body are observed and under microscope calcite remnants are recognized. Hence it is posturated that the ore material moved up through the faults, shear zones or feather cracks and was assimilated with the interbeded limestone, after that the body was affected by the successive differentiated ore solution by gradational increasing in $SiO_2$, $K_2O$ and $H_2O$. Evidently this ore deposit shows the features resulted from pyrometasomatic processes.

• Korean Journal of Soil Science and Fertilizer
• /
• v.16 no.4
• /
• pp.305-310
• /
• 1983

Spatial variability of infiltration rates of 96 samples from Hwadong SiCL was studied by using geostatistical concepts. The measurement was made at the nodes of the regular grid consisting of 12 rows and 8 columns. Sample spacing within rows and columns was 3 and 2 meters, respectively. This study illustrated the use of variogram as a tool to identify the degree of dependency of the infiltration rate on the distance between pairs of measurements and how to take advantage of this dependency. Fractile diagram showed that the distribution of observation was approximately normal. The range of the variogram was about 7.4 meters. The minimum number of samples necessary to reproduce the results similar to the 96 measured values was 8 to 10. Coefficients of theoretical variogram function for computing kriged values and kriged varionces of nuogget effect, slope, and range were 0.444 cm/day, 0.003 cm/day, and 7.4 m, respectively.

• Food Science of Animal Resources
• /
• v.33 no.6
• /
• pp.787-795
• /
• 2013

This study was carried out to investigate the characteristics of goat and cow milk yogurts containing high-exopolysaccharide fermented by Streptoccous thermophilus LFG isolated from kefir. The pH of cow milk yogurt was higher than that of goat milk yogurt. The contents of lactic acid was greater in goat milk yogurt (743.9-1043.8 mg/100 g) than in cow milk yogurt (441.6-709.9 mg/100 g). The numbers of survival lactic acid bacteria were the greatest in goat milk yogurt fermented by Str. thermophilus LFG. Viscosity was greater in cow and goat milk yogurts cultured by Str. thermophilus LFG than in yogurts by Str. thermophilus TH3. Syneresis of yogurt fermented by Str. thermophilus LFG was 9.6-16.1% and 28.2-31.8% in yogurt fermented by Str. thermophilus TH3 after 10 d storage at $4^{\circ}C$. Flavor compounds identified from goat milk were acetone, ethylbutanoate, ethyl-3-methylbutyrate, ethyl-2-butenoate and ethylhexanoate, and those from cow milk were ethylbutanoate, acetone, 2-heptanone and acetoin. Flavor compounds detected from goat milk and cow milk yogurts were acetic acid, butanoic acid, butanol, diethylcarbinol, acetone, diacetyl, decane, 2-methyl-3-pentanone, hexanal, 2-heptanone, acetoin, benzaldehyde, dimethyldisulfide, and dimethyltrisulfide. In sensory evaluation, overall preference and texture values were higher in goat milk yogurt fermented by Str. thermophilus LFG than in cow milk yogurts and the yogurt fermented by mixed culture resulted in the highest score.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.49 no.4
• /
• pp.427-435
• /
• 2016

The effects of salt solution and chlorella on the quality of canned oyster, Crassostrea gigas, were evaluated to obtain basic data regarding the processing of two canned oyster products. In canned oyster processing, the shucked oyster meat was steamed for 20 min and then drained. Then, each can (301-3) was filled with 90 g boiled oyster in 60 mL 1.5% salt solution for the control samples or 30 mL 1.5% salt solution and 30 mL chlorella culture medium for the experimental samples. All canned products were sealed using a vacuum seamer and then sterilized to Fo values of 6-12 min in a steam retort system at 118℃. The viable bacteria count, proximate composition, pH, salinity, yield, volatile basic nitrogen (VBN), amino-nitrogen, thiobarbituric acid (TBA), mineral, color value, free amino acid levels, hardness, and sensory evaluation of the two canned products were measured under various sterilization conditions. There were no significant differences in the physical or chemical factors and little difference in the overall acceptance of the control and experimental samples.