• 청정기술
• /
• 제22권4호
• /
• pp.308-315
• /
• 2016

수명특성이 우수한 실리콘 음극재를 제조하기 위해 졸겔법을 통해 $SiO_x/ZnO$ 복합체를 제조하였고, 제조된 복합체는 PVC를 탄소 전구체로 하여 탄소를 피복하였다. 복합체에 포함된 ZnO를 HCl로 제거하여 내부에 빈 공간을 만들어 충 방전에 따른 실리콘의 부피변화를 완화할 수 있게 하였다. 합성된 복합체의 결정구조와 형상을 파악하기 위해 XRD, SEM, TEM 분석을 실시하였다. 탄소 피복된 복합체에 포함된 탄소함량을 TGA를 통해 알아보았으며, 복합체의 기공구조를 확인하기 위해 BET 비표면적 분석과 BJH 기공분포를 확인하였다. 탄소의 추가로 향상된 전기전도성을 측정하였으며, 전기화학적 특성은 AC 임피던스 측정과 충 방전 및 수명특성을 확인하였다. $SiO_x/ZnO$시료에 탄소를 피복할 경우에 전기전도도가 증가하였으며, 방전용량도 증가하였다. 염산으로 ZnO를 제거한 시료의 경우에 표면적은 증가하였으나, 전지의 방전용량은 오히려 감소하였다. 탄소를 피복하지 않은 $SiO_x/ZnO$ 시료의 경우에 방전용량이 매우 낮았으며, 탄소를 피복한 후의 시료는 높은 충방전용량을 나타내었다. 수명특성의 경우, $C-SiO_x/ZnO$ 복합체(Zn : Si : C = 1 : 1 : 8)가 0.2 C의 전류량에서 50 사이클에서 $815mAh\;g^{-1}$의 용량으로 기존 흑연계 음극재보다 높은 용량을 나타내었다.

• 한국세라믹학회지
• /
• 제55권5호
• /
• pp.440-445
• /
• 2018

To control the electrical properties of a SiC heating element, we sintered $SiC-ZrB_2$composites by using the spark plasma sintering method. The addition of $ZrB_2$ particles with lower electrical conductivity to the SiC matrices with comparatively higher electrical resistivity lowers the electrical resistivities of the composite material. The $ZrB_2$ particles aggregate to form large particles and 3-1, 3-2, and 3-3 networks, i.e., conduction paths. In our study, about $1-{\mu}m$-sized $ZrB_2$ powders start to form the conduction path at about 10 vol.% of addition, namely the threshold volume. The Joule heating experiment shows that 20 vol.% $ZrB_2$-added SiC heating element has outstanding heating efficiency.

• 한국세라믹학회지
• /
• 제52권6호
• /
• pp.429-434
• /
• 2015

This study investigates the macroscopic wear behaviors of C/C and C/C-SiC composites coated with hafnium carbide (HfC). To improve the wear resistance of C/C composites, low-pressure chemical vapor deposition (LPCVD) was used to obtain HfC coating. The CVD coatings were deposited at various deposition temperatures of 1300, 1400, and $1500^{\circ}C$. The effect of the substrate material (the C/C substrate, the C/C-CVR substrate, or the C/C-SiC substrate deposited by LSI) was also studied to improve the wear resistance. The experiment used the ball-on-disk method, with a tungsten carbide (WC) ball utilized as an indenter to evaluate the wear behavior. The HfC coatings were found to effectively improve the wear resistance of C/C and C/C-SiC composites, compared with the case of a non-coated C/C composite. The former showed lower friction coefficients and almost no wear loss during the wear test because of the presence of hard coatings. The wear scar width was relatively narrower for the C/C and C/C-SiC composites with hafnium coatings. Wear behavior was found to critically depend on the deposition temperature and the material. Thus, the HfC-coated C/C-SiC composites fabricated at deposition temperatures of $1500^{\circ}C$ showed the best wear resistance, a lower friction coefficient, and almost no loss during the wear test.

• Composites Research
• /
• 제13권6호
• /
• pp.23-29
• /
• 2000

층상구조재료가 갖는 약점으로는 구성재료층 간의 열.기계적 특성 차이로 인하여 내부응력이 발생되고 비틀림 변형이 유발되어 형상 제어가 매우 어려울 뿐만 아니라, 반복적인 열 하중으로 인해 열이력을 받을 경우 접합부에서의 파손이 생길 수 있다는 것이다. 최근 층상구조에서 조직 혹은 조성이 점차적으로 변하는 계면을 삽입한 경사조성재료는 열.기계적 변형특성 차이에 의한 재료의 손상을 최소화시킬 수 있으나, 용도에 적합한 구조설계를 위해서 열.기계적 해석이 필요하다. 본 연구에서는 전자패키징용 $Al-SiC_p$ 경사조성 복합재료의 기하학적 구조와 온도변화에 따른 곡면화 변형 및 내부응력분포를 해석하고자 하였다. 한편 층상구조 $Al-SiC_p$ 경사조성 복합재료의 열변형량을 측정하고 내부응력분포를 실험적으로 구하여, 이론적으로 계산한 결과와 비교하였다. 본 연구의 해석결과는 경사조성 층상구조재료의 최적구조 설계에 유용하게 적용할 수 있다.

• 한국재료학회지
• /
• 제19권7호
• /
• pp.403-406
• /
• 2009

The friction characteristics of automotive brake friction materials that contained different ceramic content were investigated. Several kinds of raw materials, such as resin-based binder, reinforcing fiber, friction restraint, abrasive, and filling materials were mixed, pressed, and heated in order to make the brake friction materials. The contents of SiC and $BaSO_4$ changed from 5 vol% to 20 vol%, respectively. In addition to this, the content of $Al_2O_3$ adjusted from 1 vol% to 16 vol%. The surface morphology of the SiC containing sample appeared rough while more debris was observed when the contents of SiC increased. This implies that the SiC containing brake composite was not adequate for the automobile. However, the relatively smooth surface was observed in samples that contained the $Al_2O_3$. But the roughness was low with a content of 11 vol% $Al_2O_3$ compared to the other samples. This is consistent with the abrasive properties of the samples. In the case of $BaSO_4$ containing samples, the smoothes surface was observed in the contents of 15 vol% $BaSO_4$. Thus, it was concluded that the 11 vol% $Al_2O_3$ and 15 vol% $BaSO_4$ containing composite would be the optimum content for the brake composite. Similar to the results of the surface morphology, the abrasion resistance consistently decreased when the content of SiC increased. On the contrary, the sample that contained 11 vol% $Al_2O_3$ and 15 vol% $BaSO_4$ showed the highest abrasion resistance compared to the other samples.

• 한국주조공학회지
• /
• 제23권1호
• /
• pp.30-39
• /
• 2003

Porous hybrid preforms were fabricated by reactive sintering using the compacts consisting of SiC particles, Fe and Al powders. Squeeze casting processing was employed to produce the composite in which the matrix phase is Al-Si7Mg. The microstructural change and wear resistance of the composites were investigated in terms of an amount of SiC particles. The wear loss was increased with increasing the contact pressure in the alloy containing SiC particles coated with Cu. The most drastic change was found to the specimen tested at 2.5 MPa of contact pressure. Concerning the alloys containing SiC particles coated with Ni-P, a drastic increase in the wear loss exhibited at 2 MPa of contact pressure in those alloys containing 4 and 8 wt. % of SiC particles coated with Ni-P. In the alloy containing 16 wt. % a proportional increase in wear loss was observed to the change of contact pressure. With respecting to the sliding velocity, the wear loss of the alloy containing SiC particles coated with Cu increased at the initial stage of wear process and then decreased. Similar result was found in the alloys containing SiC particles coated with Ni-P. On the basis of the present results obtained, it was found that wear resistance of the alloys tested was improved to show in the order of the alloy reinforced by coated SiC particles > by uncoated SiC particles > by intermetallic compound without SiC particles.

• 한국세라믹학회지
• /
• 제29권10호
• /
• pp.791-796
• /
• 1992

SiC(p)-TiC(p) composites were prepared by gas pressure sintering technique. B4C powder and phenolic resin were added as sintering aids by 0.3 wt%-B and 3 wt%-C, TiC powder were dispersed in SiC by 0, 10, 20, 30 and 50 vol%. Flextural strength, fracture toughness and theoretical density of 70 vol% SiC-30 vol% TiC composite sintered at 220$0^{\circ}C$ by gas pressing were 540 MPa, 5.5 MPa.m1/2 and 98.8% respectively.

• 한국재료학회지
• /
• 제31권5호
• /
• pp.301-311
• /
• 2021

The conversion of all carbon preforms to dense SiC by liquid infiltration can become a low-cost and reliable method to form SiC-Si composites of complex shape and high density. Reactive sintered silicon carbide (RBSC) is prepared by covering Si powder on top of 0.5-5.0 wt% Y₂O₃-added carbon preforms at 1,450 and 1,500℃ for 2 hours; samples are analyzed to determine densification. Reactive sintering from the Y₂O₃-free carbon preform causes Si to be pushed to one side and cracking defects occur. However, when prepared from the Y₂O₃-added carbon preform, an SiC-Si composite in which Si is homogeneously distributed in the SiC matrix without cracking can be produced. Using the Si + C = SiC reaction, 3C and 6H of SiC, crystalline Si, and Y₂O₃ phases are detected by XRD analysis without the appearance of graphite. As the content of Y₂O₃ in the carbon preform increases, the prepared RBSC accelerates the SiC conversion reaction, increasing the density and decreasing the pores, resulting in densification. The dense RBSC obtained by reaction sintering at 1,500 ℃ for 2 hours from a carbon preform with 2.0 wt% Y₂O₃ added has 0.20 % apparent porosity and 96.9 % relative density.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권2호
• /
• pp.92-97
• /
• 1999

The mechanical and electrical properties of the hot-pressed and annealed $\beta-Sic$+39vol.%$ZrB_2$ electroconductive ceramic composites were investigated as a function of the liquid forming additives of $Al_2O_3+Y_2O_3(6:4wt%)$. In this microstructures, no reactions and elongated $\alpha$-SiC grains with equiaxed $ZrB_2$, gains were observed between $\beta-SiC$ and $ZrB_2$, and the relative density was over 97.6% of the theoretical density. Phase analysis of the composites by XRD revealedmostly of $\alpha$-SiC(6H, 4H), $ZrB_2$, and weakly $\beta-SiC$(15R) phase. The fracture toughness decreased with increasing $Al_2O_3+Y_2O_3$ contents and showed the highest of $6.37MPa.m^{\fraction ane-half}$ for composite added with 4wt% $Al_2O_3+Y_2O_3$ additives at room temperature. The electrical resistivity increased with increasing $Al_2O_3+Y_2O_3$contents and showed the lowest of $1.51\times10^{-4}\Omega.cm$ for composite added with $Al_2O_3+Y_2O_3$ additives at $25^{\circ}C$. This reason is the increasing tendency of pore formation according to amount of liquid forming additives $Al_2O_3+Y_2O_3$. The electrical resistivity of the composites was all positive temperature coefficient resistance(PTCR) against temperature up to $700^{\circ}C$.

• 한국결정성장학회지
• /
• 제13권6호
• /
• pp.309-314
• /
• 2003

방전 플라즈마 소결법을 적용하여 $Al_2O_3$-SiC 나노 복합체를 150$0^{\circ}C$ 이하의 온도에서 완전치밀화를 이루었다. 제조된 $Al_2O_3$-SiC 복합체는 이상 결정립 성장 없이 매우 균질한 미세구조를 형성하고 있는데, 첨가된 SiC 입자는 주로 결정립 내 및 결정립계에 존재하면서 $Al_2O_3$기지상에서 결정립 성장을 억제하는데 매우 유호하였음을 확인 할 수 있다. 한편, SiC 입자의 첨가는 크랙 회절 및 브릿징 등에 의해서 유도된 재료 강도 및 인성 강화 기구에 의해서 $Al_2O_3$-SiC 복합체의 기계적 물성을 크게 향상시켰다.