• Korean Journal of Materials Research
• /
• v.24 no.9
• /
• pp.474-480
• /
• 2014

Process conditions for the impregnation of polycarbosilane preceramic polymer into SiC-based composites were investigated. Two kinds of preceramic polymer (PCP) was impregnated into SiC-fiber fabrics with different solvents of n-hexane and divinylbenzene (DVB). Both microstructural observations and mechanical tests were conducted to evaluate the impregnation. The matrix phases were particulated in the case of hexane solvents. Apparent relative density of the matrix was about 78.8%. The density of matrix was increased to about 96.1-98.8% when the DVB was used; however, brittle fracture was observed during a bending test. The modulus of toughness was less than $0.74J/m^3$. The fabric impregnated with a mixed PCP-dissolved solution showed intermediate characteristics with relative high density of filling (apparent density of ~96.1%) as well as proper bending behavior. The modulus of toughness was increased to about $5.31J/m^3$. The composites developed by changing the precursor and solvent suggested the possibility of fabricating SiCf/SiC composites without a fiber to matrix interphase coating.

• Journal of Korea Foundry Society
• /
• v.13 no.4
• /
• pp.369-381
• /
• 1993

Aluminum alloy(AC8A) matrix composites reinforced with SiC particles(10% in vol.) were fabricated by Centrifugal Spray Deposition(CSD) process. The microstructures were investigated in order to evaluate both the mixing mode between aluminum matrix and SiC particles, and the effect of SiC particles on the cooling behaviours of droplets during flight and preforms deposited. A non-continuum mathematical calculation was performed to explain and to quantify the evolution of microstructures in the droplets and preforms deposited. Conclusions obtained are as follows; 1. The powders produced by CSD process showed, in general, ligament type, and more than 60% of the powders produced were about 300 to 850 um in size. 2. AC8A droplets solidified during flight showed fine dendritic structure, but AC8A droplets mixed with SiC particles showed fine equiaxed grain structure, and eutectic silicon were formed to crystallize granularly between fine aluminum grains. 3. SiC particles seem to act as a nucleation sites for pro-eutectic silicon during solidification of AC8A alloy. 4. The microstructure of composite powders formed by CSD process showed particle embedded type, and resulted in dispersed type microstructure in preforms deposited. 5. The pro-eutectic silicon crystallized granularly between fine aluminum grains seem to prohibit grains from growth during spray deposition process. 6. The interfacial reactions between aluminum matrix and SiC particles were not observed from the deposit performs and the solidified droplets. 7. The continuum model seem to be useful in connecting the processing parameters with the resultant microstructures. From these results, it was concluded that the fabrication of aluminum matrix composites reinforced homogeneously with SiC particles was possible.

• Composites Research
• /
• v.15 no.3
• /
• pp.1-10
• /
• 2002

The effect of size of SiC particles and additive Mg content on the mechanical properties and wear characteristics were investigated for the SiCp/AC8A composites fabricated by pressureless infiltration process. Results showed that the hardness and the bending strength increased with decreasing the size of SiC particle. By increasing the Mg content the hardness of SiCp/AC8A composites increased due to the hard reaction products, however the bending strength decreased by formation of coarse precipitates and high porosity level. The SiCp/AC8A composites exhibited about 6 times higher wear resistance compared with AC8A alloy at high sliding velocity and as increasing the particle size, wear resistance was improved. The major wear mechanical of SiCp/AC8A composites exhibited the abrasive wear at low to high sliding velocity whereas AC8A alloy showed adhesive and melt wear at high sliding velocity.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.25 no.1
• /
• pp.37-54
• /
• 1999

Planarized SiO$_2$ particles were prepared by two-step reduction method of making much smaller particles, micron-sized ones, to improve spreadability, adherence, and smoothness. Various pigments known as flaky extender usually have terrace layers on their surfaces, but SiO$_2$ Particles in this study exhibit a smooth surface structure. These single SiO$_2$ particles were used for core particles to prepare the composite particles coated with ultra fine TiO$_2$ particles by a homogeneous precipitation method. The thickness and the morphology of the deposited TiO$_2$ layer could be altered by adjusting the reactant concentrations, reaction time and temperature. The characteristics of SiO$_2$/TiO$_2$composite in the field of color cosmetics is to give a UV-cut effect and to enhance the chroma of human skin color, one of optical properties.

• Korean Journal of Materials Research
• /
• v.20 no.9
• /
• pp.451-456
• /
• 2010

A promising candidate material for a $H_2$ permeable membrane is SiC due to its many unique properties. A hydrogen-selective SiC membrane was successfully fabricated on the outer surface of an intermediate multilayer $\gamma-Al_2O_3$ with a graded structure. The $\gamma-Al_2O_3$ multilayer was formed on top of a macroporous $\alpha-Al_2O_3$ support by consecutively dipping into a set of successive solutions containing boehmite sols of different particle sizes and then calcining. The boehmite sols were prepared from an aluminum isopropoxide precursor and heated to $80^{\circ}C$ with high speed stirring for 24 hrs to hydrolyze the precursor. Then the solutions were refluxed at $92^{\circ}C$ for 20 hrs to form a boehmite precipitate. The particle size of the boehmite sols was controlled according to various experimental parameters, such as acid types and acid concentrations. The topmost SiC layer was formed on top of the intermediate $\gamma-Al_2O_3$ by pyrolysis of a SiC precursor, polycarbosilane, in an Ar atmosphere. The resulting amorphous SiC-on-$Al_2O_3$ composite membrane pyrolyzed at $900^{\circ}C$ possessed a high $H_2$ permeability of $3.61\times10^{-7}$ $mol{\cdot}m^{-2}{\cdot}s^{-1}{\cdot}Pa^{-1}$ and the $H_2/CO_2$ selectivity was much higher than the theoretical value of 4.69 in all permeation temperature ranges. Gas permeabilities through a SiC membrane are affected by Knudsen diffusion and a surface diffusion mechanism, which are based on the molecular weight of gas species and movement of adsorbed gas molecules on the surface of the pores.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.10a
• /
• pp.248-253
• /
• 1998

Recently, the uses of Ceramic/metal bonded joints, resin/metal joints, adhesive joints, composite materials which are composed of dissimiliar materials have increased in various industry fields. Since the ceramic/metal bonded joints material is made at a high temperature, residual stress distributions due to differences in material properties were investigated by varying material parameters. The two dimensional finite element analysis was performed to study residual stress distribution in Si3N4/SM45C bonded joint with a copper interlayer between the silicon nitride(Si3N4) and the structural carbon steel(SM45C) and 4-point bending tests were carried out under room temperature. Fracture surface and crack propagation path were observed using scanning electron microscope and characteristics of its fracture was discussed.

• Carbon letters
• /
• v.1 no.1
• /
• pp.12-16
• /
• 2000

Carbon fiber was reacted with gaseous silicon monoxide which is produced from pack-powder mixture at elevated temperature. As a result of the reaction, two kinds of SiC fiber were obtained. The first one was SiC fibers which were converted from carbon fiber. The fiber is constituted with polycrystal like fine grains or monolithic crystals that have a size from sub-micron to $10\;{\mu}m$. Their size depends on the temperature during the conversion reaction. The second one was ultra-fine SiC fibers that were found on the surface of the converted SiC fibers. The ultra-fine fibers have diameters from 0.08 to $0.2\;{\mu}m$ and their aspect ratio were larger than 100. The chemical composit ion of the ultra-fine fibers was analyzed using an Auger electron spectroscopy. In result, the fibers consist of 51% silicon, 38% carbon and 11% oxygen by weight.

• Journal of the Korean Ceramic Society
• /
• v.50 no.6
• /
• pp.495-497
• /
• 2013

SiC-$Y_2O_3$ porous composites were fabricated using $Y_2O_3$ powders synthesized by sol-gel process to control physical and thermo-chemical properties. $Y_2O_3$ powders were mixed with SiC powders by co-pressing with HPCS (hydridopolycarbosilane) binder at moderate temperature. The properties of membranes were characterized by XRD, FE-SEM, and BET surface analysis. Hydrogen permeability was performed at various temperatures.

• Korean Journal of Materials Research
• /
• v.6 no.11
• /
• pp.1090-1098
• /
• 1996

개조한 가스 금속 아아크 용접공정을 이용하여 SiC/AI 금속기 복합재료를 제조하고 그 특성을 조사하였다. AI 모재위에 강화입자의 크기와 부피분율을 변화하여 다양한 SiC/AI 복합재료층을 제조하였고, 만들어진 복합재료층의 특성은 미세조직관찰과 미소경도시험을 통하여 이루어졌다. 복합재료층의 두께는 약 7-8mm로 측정되었고 균일한 강화입자의 분포도를 얻을 수 있었다. 분산입자의 부피분률은 Ar가스의 유량에 의하여 조절하였고 분산입자의 부피분률이 증가하고 크기가 작아짐에 따라 기지의 수지상 응고조직은 더욱 미세화되었다. 복합재료의 부피경도는 분산입자의 부피분률이 감소함에 따라 낮아졌으나 입자 크기에는 크게 변화가 없는 것으로 나타났다.

• Journal of the Korean Ceramic Society
• /
• v.51 no.6
• /
• pp.566-569
• /
• 2014

ZnO and SiC powders were fabricated to make crack-free composite membranes. Parts of some membranes were re-treated with an encapsulation process. These membranes were characterized by XRD, BET, and FE-SEM analyzes. The hydrogen permeation fluxes of the encapsulated and heat-treated membranes after encapsulation were observed using Sievert's type equipment. Values were measured at 1 bar with increasing temperatures. The obtained values of encapsulated and further heat-treated membrane at 298 K were $4.20{\times}10^{-6}$ and $8.64{\times}10^{-5}mol/m^2sPa$, respectively.