• Korean Chemical Engineering Research
• /
• v.49 no.5
• /
• pp.664-668
• /
• 2011

Spherical alumina precursors represented by $AlO_xCl_y(OH)_z$, 30~200 nm in particle diameter, were prepared by partial hydrolysis of $AlCl_3$ vapor in a 500 ml reactor. Investigated on the particle morphology and size were the effects of the reaction time, the stirring speed and the reaction temperature. The particle morphology and size was insensitive to the reaction time in the range 20 to 300 s. The variation of the stirring speed from 0 to 300 and 800 rpm showed that the particle size was the largest at 0 rpm. As the temperature was varied from 180 to 190, 200, $140^{\circ}C$, the particle size showed a maximum at $190^{\circ}C$. By calcination of the as-produced particles at $1,200^{\circ}C$ for 6h with a heating rate of $10^{\circ}C$/min, ${\alpha}$-alumina particles 45 nm in surface area equivalent diameter were obtained. The particle shape after calcination turned wormlike due to sintering between neighboring particles. A rapid calcination at $1400^{\circ}C$ for 0.5 h with a higher heating rate of $50^{\circ}C$/min reduced the sintering considerably. An addition of $SiCl_4$ or TMCTS(2,4,6,8-tetramethylcyclosiloxane) to the $AlCl_3$ reduced the sintering effectively in the calcination step; however, peaks of ${\gamma}$ or mullite phase appeared. An addition of $AlF_3$ to the particles obtained from the hydrolysis resulted in a hexagonal disc shaped alumina particles.

• Korean Journal of Materials Research
• /
• v.20 no.11
• /
• pp.611-616
• /
• 2010

A cobalt oxide - tin oxide nanocomposite based gas sensor on an $SiO_2$ substrate was fabricated. Granular thin film of tin oxide was formed by a rheotaxial growth and thermal oxidation method using dc magnetron sputtering of Sn. Nano particles of cobalt oxide were spin-coated on the tin oxide. The cobalt oxide nanoparticles were synthesized by polymer-assisted deposition method, which is a simple cost-effective versatile synthesis method for various metal oxides. The thickness of the film can be controlled over a wide range of thicknesses. The composite structures thus formed were characterized in terms of morphology and gas sensing properties for reduction gas of $H_2$. The composites showed a highest response of 240% at $250^{\circ}C$ upon exposure to 4% $H_2$. This response is higher than those observed in pure $SnO_2$ (90%) and $Co_3O_4$ (70%) thin films. The improved response with the composite structure may be related to the additional formation of electrically active defects at the interfaces. The composite sensor shows a very fast response and good reproducibility.

• Bulletin of the Korean Chemical Society
• /
• v.25 no.5
• /
• pp.687-693
• /
• 2004

Composite membranes with a titania layer were prepared by soaking-rolling method with the titania sol of nanoparticles formed in the sol-gel process and investigated regarding the vapor permeation of various organic mixtures. The support modification was conducted by pressing $SiO_2$ xerogel of 500 nm in particle size under 10 MPa on the surface of a porous stainless steel (SUS) substrate and designed the multi-layered structure by coating the intermediate layer of ${\gamma}-Al_2O_3$. Microstructure of titania membrane was affected by heat-treatment and synthesis conditions of precursor sol, and titania formed at calcination temperature of 300$^{\circ}C$ with sol of [$H^+$]/[TIP]=0.3 possessed surface area of 210 $m^2$/g, average pore size of 1.25 nm. The titania composite membrane showed high $H_2/N_2$ selectivity and water/ethanol selectivity as 25-30 and 50-100, respectively. As a result of vapor permeation for water-alcohol and alcohol-alcohol mixture, titania composite membrane showed water-permselective and molecular-sieve permeation behavior. However, water/methanol selectivity of the membrane was very low because of chemical affinity of permeants for the membrane by similar physicochemical properties of water and methanol.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.8
• /
• pp.531-538
• /
• 2015

This study examined the size and shape of the nano-silver particle through the analysis of electrical resistance when synthesizing nano-sized silver by using the chemical liquid reduction. Changes in particle behaviors formed according to the changes in electronic characteristics by electric resistance in each time period in the beginning of reduction reaction in a course of synthesizing the nano-silver particle formation were studied. In addition, analysis was conducted on particle behaviors according to the changes in concentration of $AgNO_3$ and in temperature at the time of reduction and nucleation and growth course when synthesizing the particles based on the particle behaviors were also examined. As the concentration of $AgNO_3$ increased, the same amount of resistance of approximately $5{\Omega}$ was increased in terms of initial electronic resistance. Furthermore, according to the result of formation of nuclear growth graph and estimation of slope based on estimated resistance, slops of $6.25{\times}10^{-3}$, $2.89{\times}10^{-3}$, and $1.85{\times}10^{-3}$ were derived from the concentrations of 0.01 M, 0.05 M, and 0.1 M, respectively. As the concentration of $AgNO_3$ increased, the more it was dominantly influenced by the nuclear growth areas in the initial phase of reduction leading to increase the size and cohesion of particles. At the time of reduction of nano-silver particle, the increases of initial resistance were $4{\Omega}$, $4.2{\Omega}$, $5{\Omega}$, and $5.3{\Omega}$, respectively as the temperature increased. As the temperature was increased into $23^{\circ}C$, $40^{\circ}C$, $60^{\circ}C$, and $80^{\circ}C$, slopes were formed as $4.54{\times}10^{-3}$, $4.65{\times}10^{-3}$, $5.13{\times}10^{-3}$, and $5.42{\times}10^{-3}$ respectively. As the temperature increased, the particles became minute due to the increase of nuclear growth area in the particle in initial period of reduction.