• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.65-65
• /
• 2009

High temperature silicon carbide Schottky diode was fabricated with Au deposited on poly 3C-SiC thin film grown on p-type Si(100) using atmospheric pressure chemical vapor deposition. The charge transport mechanism of the diode was studied in the temperature range of 300 K to 550 K. The forward and reverse bias currents of the diode increase strongly with temperature and diode shows a non-ideal behavior due to the series resistance and the interface states associated with 3C-SiC. The charge transport mechanism is a temperature activated process, in which, the electrons passes over of the low barriers and in turn, diode has a large ideality factor. The charge transport mechanism of the diode was analyzed by a Gaussian distribution of the Schottky barrier heights due to the Schottky barrier inhomogeneities at the metal-semiconductor interface and the mean barrier height and zero-bias standard deviation values for the diode was found to be 1.82 eV and $s_0$=0.233 V, respectively. The interface state density of the diode was determined using conductance-frequency and it was of order of $9.18{\times}10^{10}eV^{-1}cm^{-2}$.

• Proceedings of the KIEE Conference
• /
• 2001.10a
• /
• pp.192-195
• /
• 2001

In this report, we firstly have investigated the electrical characteristics of silicon carbide (SiC) schottky barrier diode and compared the characteristics to those of conventional Si diode through simulation and experiment. Secondly we have investigated the influence of two kinds of diodes to the power conversion circuit of the systems. From the investigation results it is verified that SiC schottky barrier diode is more superior to Si diode in thermal and reverse recovery, characteristics, which are the important factors in the size reduction and higher reliability of the systems. Finally though the experiment applied to PFC(Power Factor Correction) circuits, we precisely verified excellency to thermal characteristic of SiC schottky barrier diode any other diode.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.10
• /
• pp.618-622
• /
• 2014

The temperature dependent characteristics on the properties of SiC Schottky Diode has been investigated. In this study, the temperature dependent current-voltage characteristics of the SiC Schottky diode were measured in the range of 300 ~ 500 K. Divided into pre- and post- irradiated device was measured. The barrier height after irradiation device at 500 K increased 0.15 eV compared to 300 K, the barrier height of pre- neutron irradiated Schottky diode increased 0.07 eV. The effective barrier height after irradiation increased from 0.89 eV to 1.05 eV. And ideality factor of neutron irradiated Schottky diode at 500 K decreased 0.428 compared to 300 K, the ideality factor of pre- neutron irradiated Schottky diode decreased 0.354. Also, a slight positive shift in threshold voltage from 0.53 to 0.68 V. we analyzed the effective barrier height and ideality factor of SiC Schottky diode as function of temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.195-196
• /
• 2009

This paper describes the fabrication and characteristics of polycrystalline 3C-SiC thin film diodes for extreme environment applications, in which the this thin film was deposited onto oxidized Si wafers by APCVD using HMDS In this work, the optimized growth temperature and HMDS flow rate were $1,100^{\circ}C$ and 8sccm, respectively. A Schottky diode with a Au, Al/poly 3C-SiC/$SiO_2$/Si(n-type) structure was fabricated and its threshold voltage ($V_d$), breakdown voltage, thickness of depletion layer, and doping concentration ($N_D$) values were measured as 0.84V, over 140V, 61nm, and $2.7{\times}10^{19}cm^2$, respectively. To produce good ohmic contact, Al/3C-SiC were annealed at 300, 400, and $500^{\circ}C$ for 30min under a vacuum of $5.0{\times}10^{-6}$Torr. The obtained p-n junction diode fabricated by poly 3C-SiC had similar characteristics to a single 3C-SiC p-n junction diode.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.3
• /
• pp.1066-1074
• /
• 2015

This paper presents the reverse recovery characteristic according to the change of switching states when Si diode and SiC diode are used as clamp diode and proposes a method to minimize the switching loss containing the reverse recovery loss in the neutral-point-clamped inverter at low modulation index. The previous papers introduce many multiple circuits replacing Si diode with SiC diode to reduce the switching loss. In the neutral-point-clamped inverter, the switching loss can be also reduced by replacing device in the clamp diode. However, the switching loss in IGBT is large and the reduced switching loss cannot be still neglected. It is expected that the reverse recovery effect can be infrequent and the switching loss can be considerably reduced by the proposed method. Therefore, it is also possible to operate the inverter at the higher frequency with the better system efficiency and reduce the volume, weight and cost of filters and heatsink. The effectiveness of the proposed method is verified by numerical analysis and experiment results.

• Journal of the Semiconductor & Display Technology
• /
• v.21 no.2
• /
• pp.123-126
• /
• 2022

We investigated deep levels in n-type 4H-SiC epitaxy layer of the Positive-Intrinsic-Negative diode and Schottky barrier diodes by using deep level transient spectroscopy. Despite the excellent performance of 4H-SiC, research on various deep level defects still requires a lot of research to improve device performance. In Positive-Intrinsic-Negative diode, two defects of 196K and 628K are observed more than Schottky barrier diode. This is related to the action of impurity atoms infiltrating or occupying the 4H-SiC lattice in the ion implantation process. The I-V characteristics of the Positive-Intrinsic-Negative diode shows about ~100 times lower the leakage current level than Schottky barrier diode due to the grid structures in Positive-Intrinsic-Negative. As a result of comparing the capacitance of devices diode and Schottky barrier diode devices, it can be seen that the capacitance value lowered if it exists the P implantation regions from C-V characteristics.

• Proceedings of the KIEE Conference
• /
• 1999.11d
• /
• pp.938-940
• /
• 1999

We have fabricated SiC Schottky diode for high temperature applications. SiC thin film for drift region has been deposited by ICP-CVD. In order to establish metallization conditions, we have extracted the device parameters of the Schottky diode from the forward I-V characteristics and the C-V characteristics as a function of temperature. The ideality factor was varied from 2.07 to 1.15 and the barrier height was also varied from 1.26eV to 1.92eV with increase of temperature. The reverse blocking voltage was 183 V.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2007.06a
• /
• pp.179-182
• /
• 2007

Polycrystaline (poly) 3C-SiC thin film on n-type and p-type Si were deposited by APCVD using HMDS, $H_2$, and Ar gas at $1180^{\circ}C$ for 3 hour. And then the schottky diode with Au/poly 3C-Sic/Si(n-type) structure was fabricated. Its threshold voltage ($V_d$), breakdown voltage, thickness of depletion layer, and doping concentration ($N_D$) value were measured as 0.84 V, over 140 V, 61nm, and $2.7{\times}10^{19}\;cm^3$, respectively. The p-n junction diode fabricated by poly 3C-SiC was obtained like characteristics of single 3C-SiC p-n junction diode. Therefore, its poly 3C-SiC thin films are suitable MEMS applications in conjuction with Si fabrication technology.

• Journal of Sensor Science and Technology
• /
• v.16 no.4
• /
• pp.259-262
• /
• 2007

This paper describes the electrical characteristics of polycrystalline (poly) 3C-SiC thin film diodes, in which poly 3C-SiC thin films on n-type and p-type Si wafers, respectively, were deposited by APCVD using HMDS, $H_{2}$, and Ar gas at $1150^{\circ}C$ for 3 hr. The schottky diode with Au/poly 3C-SiC/Si (n-type) structure was fabricated. Its threshold voltage ($V_{bi}$), breakdown voltage, thickness of depletion layer, and doping concentration ($N_{D}$) value were measured as 0.84 V, over 140 V, 61 nm, and $2.7{\times}10^{19}cm^{-3}$, respectively. Moreover, for the good ohmic contact, Al/poly 3C-SiC/Si (n-type) structure was annealed at 300, 400, and $500^{\circ}C$, respectively for 30 min under the vacuum condition of $5.0{\times}10^{-6}$ Torr. Finally, the p-n junction diodes fabricated on the poly 3C-Si/Si (p-type) were obtained like characteristics of single 3CSiC p-n junction diode. Therefore, poly 3C-SiC thin film diodes will be suitable for microsensors in conjunction with Si fabrication technology.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.4
• /
• pp.261-265
• /
• 2011

This paper describes the fabrication and characteristics of a Au/Ni/Ti/3C-SiC Schottky diode with field plate (FP) edge termination. The Schottky contacts were annealed for 30 min at temperatures ranging from 0 to $800^{\circ}C$. At annealing temperature of $600^{\circ}C$, it showed an inhomogeneous Schottky barrier and had the best electrical characteristics. However, the annealing of $800^{\circ}C$ replaced it with ohmic behaviors because of the formation of many different types of nickel silicides. The fabricated Schottky diode had a breakdown voltage of 200 V, Schottky barrier height of 1.19 eV and worked normally even at $200^{\circ}C$.