• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.2
• /
• pp.187-194
• /
• 2012

The strength of particle-reinforced metal matrix composites is, in general, known to be increased by the geometrically necessary dislocations punched around a particle that form during cooling after consolidation because of coefficient of thermal expansion (CTE) mismatch between the particle and the matrix. An additional strength increase may also be observed, since another type of geometrically necessary dislocation can be formed during extensive deformation as a result of the strain gradient plasticity due to the elastic-plastic mismatch between the particle and the matrix. In this paper, the magnitudes of these two types of dislocations are calculated based on the dislocation plasticity. The dislocations are then converted to the respective strengths and allocated hierarchically to the matrix around the particle in the axisymmetric finite-element unit cell model. The proposed method is shown to be very effective by performing finite-element strength analysis of $SiC_p$/Al2124-T4 composites that included ductile failure in the matrix and particlematrix decohesion. The predicted results for different particle sizes and volume fractions show that the length scale effect of the particle size obviously affects the strength and failure behavior of the particle-reinforced metal matrix composites.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2006.04a
• /
• pp.50-50
• /
• 2006

• Journal of Korean Ophthalmic Optics Society
• /
• v.5 no.2
• /
• pp.207-210
• /
• 2000

The SiC-TiC composites materials for glasses lens cutting were fabricated by hot-pressing and annealing. The amount of TiC was 0, 10, 20, 30wt% in the mixture of ${\beta}-SiC$. The microstructure of materials for glasses lens cutting was very dependent on the TiC amount. The introduction of larger amount of TiC improved fracture toughness, optical microscope and XRD analysis of the surface of samples were carried out. An in situ-toughened microstructure, consisted of distributed elongated SiC, matrix like TiC grains was developed by using ${\beta}-SiC$. Typical hardness and fracture toughness of materials for spectacle lens cutting were 14.9 GPa and $5.7MPa{\cdot}m^{1/2}$, respectively.

• Journal of the Korean Ceramic Society
• /
• v.41 no.2
• /
• pp.125-130
• /
• 2004

The effect of SiC particle size on the microstructures and mechanical properties of A1$_2$O$_3$-SiC composite was investigated. Two types of SiC powders having average particle sizes of 0.15 ${\mu}{\textrm}{m}$ and 3 ${\mu}{\textrm}{m}$ were used. The grain growth in the specimen containing 0.15 ${\mu}{\textrm}{m}$ SiC was effectively inhibited due to the fine SiC particles. However, after the formation of some abnormal grains, fast and exaggerated grain growth occurred which led to the microstructure of large grains with irregular shape. Fracture strength decreased due to the abnormal large grains. On the other hand, for specimen containing 3 ${\mu}{\textrm}{m}$ SiC showed normal grain growth behavior from initial sintering stage. Large SiC particles, however, effectively inhibited exaggerated grain growth after nucleation of a few abnormal grains. As a consequence, microstructure consisted of homogeneous elongated grains. In the A1$_2$O$_3$-2.5SiC(0.15 ${\mu}{\textrm}{m}$)-2.5SIC(3 ${\mu}{\textrm}{m}$) composite fabricated by mixing the two types of SiC powder, abnormal grain growth occurred. However, the good fracture strength was maintained regardless of microstructural changes in this specimen.

• Journal of Ocean Engineering and Technology
• /
• v.10 no.4
• /
• pp.84-91
• /
• 1996

A fractal analysis on fracture surface of aluminium-particulate SiC composites was attempted. As the volume fraction of SiC in composites increases, the fractal dimension tends to increase. However, no correlation between the fractal dimension and the fracture toughness in terms of critical energy release rate was observed. Since the fractal dimension represents the roughness of fracture surface, the fracture toughness would be a function of not only fracture surface roughness but also additional parameters. Thus the applicability of fractal analysis to the estimation of fracture toughness must depend on the proper choice and interpretation of additioal paramerters. In this paper, the size of characteristic strctural unit for fracture was considered as an additional parameter. As a result, the size appeared to be a function of only volume fraction of SiC. Finally, a master curve for fracture toughness of aluminium-particulate SiC composites was proposed as a function of fractal dimension and volume fraction of SiC.

• Korean Journal of Materials Research
• /
• v.5 no.8
• /
• pp.953-959
• /
• 1995

It was investigated that reinforced species, billet condition and extrusion variation in Al 6061 composite material effected on extrusion process of particulate reinforced composite material. The strength of composite material with reinforcement species revealed SiC$\sub$w/> A1$_2$O$\sub$3f/ > A1$_2$O$\sub$3f/ > A1$_2$O$\sub$3f/ orderly. K$\sub$w/ increased as volute fraction increased in all composite material. The composite materials reinforced by A1$_2$ $O_3$required the larger pressure in hot extrusion process than those by SiC$\sub$p/ at all condition. Extrusion process tended to decrease as the semi-angle of extrusion dies increased because larger contact area caused larger shear friction. Extrusion temperature went up about 50$^{\circ}C$ in low elevated deformation temperature. In extrusion temperature above 500$^{\circ}C$, severe tearing occurred on extrusion surface. More reinforcement in volume fraction, more hot tearing.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.3 s.234
• /
• pp.425-431
• /
• 2005

The efficiency of complex slurry preparation route for developing the high performance SiC matrix of $RS-SiC_{f}/SiC$ composites has been investigated. The green bodies for RS-SiC materials prior to the infiltration of molten silicon were prepared with various C/SiC complex slurries, which associated with both the sizes of starting SiC particles and the blending conditions of starting SiC and C particles. The characterization of Rs-SiC materials was examined by means of SEM, EDS and three point bending test. Based on the mechanical property-microstructure correlation, the process optimization is also discussed. The flexural strength of Rs-SiC materials greatly depended on the content of residual Si. The decrease of starting SiC particle size in the C/SiC complex slurry was effective for improving the flexural strength of RS-SiC materials.

• Journal of the Korean Chemical Society
• /
• v.47 no.6
• /
• pp.619-624
• /
• 2003

The $Gd_{1.9-x}Li_{0.1}Eu_xO_3$ (x=0.02, 0.05, 0.08, and 0.12) powders (${\thickapprox}1{\mu}m$) synthesized by sol-gel method, whose surfaces are modified in a colloidal silica suspension (size of $SiO_2$ particles: ${\sim}30$ nm), have been fabricated to highly stable and effective luminescent films on the glass substrates. Thanks to the fused $SiO_2$ nano particles in the vicinity of the glass softening temperature (at around $700^{\circ}C$), $Gd_{1.9-x}Li_{0.1}Eu_xO_3$ powders are strongly attached onto the surface of glass substrate (>9H, pencil hardness tester). This simple and low-cost method to get $Gd_{1.9-x}Li_{0.1}Eu_xO_3$ phosphor films without any loss of luminescence brightness would promise for applications to display devices.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.139-139
• /
• 2010

금속 실리사이드 나노입자는 열적 및 화학적 안정성이 뛰어나고, 절연막내에 일함수 차이에 따라 깊은 양자 우물구조가 형성되어 비휘발성 메모리 소자를 제작할 수 있다. 그러나 단일 $SiO_2$ 절연막을 사용하였을 경우 저장된 전하의 정보 저장능력 및 쓰기/지우기 시간을 향상시키는 데 물리적 두께에 따른 제한이 따른다. 본 연구에서는 터널장벽 엔지니어링을 통하여 물리적인 두께는 단일 $SiO_2$ 보다는 두꺼우나 쓰기/지우기 동작을 위하여 인가되는 전기장에 의하여 상대적으로 전자가 느끼는 상대적인 터널 절연막 두께를 감소시키는 방법으로 동작속도를 향상 시킨 $SiO_2/Si_3N_4/SiO_2$ 및 $Si_3N_4/SiO_2/Si_3N_4$ 터널 절연막을 사용한 금속 실리사이드 나노입자 비휘발성 메모리를 제조하였다. 제조방법은 우선 p-type 실리콘 웨이퍼 위에 100 nm 두께로 증착된 Poly-Si 층을 형성 한 이후 소스와 드레인 영역을 리소그래피 방법으로 형성시켜 트랜지스터의 채널을 형성한 이후 그 상부에 $SiO_2/Si_3N_4/SiO_2$ (2 nm/ 2 nm/ 3 nm) 및 $Si_3N_4/SiO_2/Si_3N_4$ (2 nm/ 3 nm/ 3 nm)를 화학적 증기 증착(chemical vapor deposition)방법으로 형성 시킨 이후, direct current magnetron sputtering 방법을 이용하여 2~5 nm 두께의 $WSi_2$ 및 $TiSi_2$ 박막을 증착하였으며, 나노입자 형성을 위하여 rapid thermal annealing(RTA) system을 이용하여 $800{\sim}1000^{\circ}C$에서 질소($N_2$) 분위기로 1~5분 동안 열처리를 하였다. 이후 radio frequency magnetron sputtering을 이용하여 $SiO_2$ control oxide layer를 30 nm로 증착한 후, RTA system을 이용하여 $900^{\circ}C$에서 30초 동안 $N_2$ 분위기에서 후 열처리를 하였다. 마지막으로 thermal evaporator system을 이용하여 Al 전극을 200 nm 증착한 이후 리소그래피와 식각 공정을 통하여 채널 폭/길이 $2{\sim}5{\mu}m$인 비휘발성 메모리 소자를 제작하였다. 제작된 비휘발성 메모리 소자는 HP 4156A semiconductor parameter analyzer와 Agilent 81101A pulse generator를 이용하여 전기적 특성을 확인 하였으며, 측정 온도를 $25^{\circ}C$, $85^{\circ}C$, $125^{\circ}C$로 변화시켜가며 제작된 비휘발성 메모리 소자의 열적 안정성에 관하여 연구하였다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.6
• /
• pp.309-314
• /
• 2003

A spark plasma sintering technique has been used for the fabrication of $Al_2O_3$-SiC nanocomposites at the low temperature of $1100^{\circ}C$∼$1500^{\circ}C$. The sintered $Al_2O_3$-SiC composites shows very homogeneous microstructure without any particular abnormal grain growth, indicating that the addition of nano-sized SiC particles is very effective to control grain growth and to induce the residual stress in the $Al_2O_3$ matrix, resulting in the intragranular fracture. These SiC particles are present in the grain boundaries and also intragrain, depending on the sintering condition, and improve remarkably the mechanical properties of $Al_2O_3$-SiC composite through the mechanisms of strengthening and toughening induced by crack diffraction and crack bridging.