• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.4
• /
• pp.443-449
• /
• 2012

Nanoskins were fabricated on a Ti-6Al-4V material by carrying out various surface treatments, i.e., deep rolling, laser shot peening, and ultrasonic nanocrystal surface modification (UNSM). These surface treatments are newly developed techniques and are becoming more popular for industrial applications. Fatigue tests were carried out using material test system (MTS); these tests included the axial loading tension-compression fatigue test (R = -1, RT, 5 Hz, sinusoidal wave) and rotating bending fatigue test (R = -1, RT, 3200 rpm). The analysis of the crack initiation pattern in the UNSM-treated material indicated that the crack was interior originating in the axial loading tension-compression cycle, and was surface originating in the bending fatigue test. UNSM treatment significantly improved the fatigue strength for the regime of above $10^6$ cycles that S-N curve of rotating bending stress clearly show the performance of a 5 mm titanium specimen after UNSM treatment is similar to that of an untreated 6 mm titanium specimen.

• The Journal of Engineering Geology
• /
• v.4 no.2
• /
• pp.187-206
• /
• 1994

Through a computer model study, optimum system configuration and field parameters were determined for high-resolution marine reflection surveys. Characteristics of far-field signatures were analysed in both time and frequency domains for the six individual R/V Onnuri. The analysis shows that the cluster fired at the depth of 2m below the sea surface generates the most ideal far-field signatures among the above seismic sources. Compared with the 96-channel streamer on the R/V Onnuri, the 12-channel streamer is suitable for shallow reflection profiling due to its high resolution both in the vertical and horizontal directions despite its lower signal-to-noise ratio. Considering factors including target depth, frequency range, airgun volume, number of recording channels, and capacity of compressors, optimum values for record length, sample period, and shot interval are believed to be is, 1ms, and 3.125m or 6.25m, respectively.

• The KSFM Journal of Fluid Machinery
• /
• v.10 no.5
• /
• pp.54-63
• /
• 2007

A barrel is a high length-to-diameter ratio cylinder that is influenced by environmental factors such as sunlight, precipitation, wind and clouds. Cross-barrel temperature differences caused by uneven heating or cooling lead to thermal deformation that degrades accuracy. Therefore, a barrel is covered by thermal shrouds to minimize the type of thermal deformation, "fall-of-shot". In this paper, an analytical and experimental study is presented to design the thermal shrouds for a gun barrel and to evaluate the thermal shroud effect. First, an analytical study on the thermal shroud effect to minimize thermal deformation of a gun barrel by sunlight and wind is performed. The coupled analysis of thermal fluid dynamics of the air flow between a barrel and thermal shrouds and thermal stresses of a barrel Is performed to clarify both the thermal shroud effect and the drift in gun muzzle orientation by thermal deformation. Second, experiments are carried out to test and evaluate the thermal shroud effect on the performance of a gun barrel. The drift in gun muzzle orientation against the solar radiation is confirmed by the experiments, and the results well agree with the analytical estimation. Third, three principal design factors that are presumed to have an effect on the performance of the thermal shrouds are also analyzed; sorts of shroud materials, wall-thickness of thermal shrouds, and distance of the gap between a barrel and thermal shrouds.

• Journal of Korea Foundry Society
• /
• v.31 no.5
• /
• pp.274-283
• /
• 2011

The vacuum die casting is a promising candidate of the stamping process for fabrication of fuel cell bipolar plate due to its advantages, such as precision casting, mass production and short production time. This study proposes vacuum die casting process to fabricate bipolar plates in fuel cell. Bipolar plates were fabricated under various injection conditions such as molten metal temperature and injection velocity. Also, according to injection velocity conditions, simulation results of MAGMA soft were compared to the experimental results. In case of melt temperature $650^{\circ}C$, misrun occurred. When the melt temperature was $730^{\circ}C$, mechanical properties were low due to dendrite microstructure. Injection velocity has to set at more than 2.0 m/s to fabricate the sound sample. When melt temperature, injection velocity (Fast shot), and vacuum pressure are $700^{\circ}C$, 2.5 m/s and 30 kPa respectively, sample had good formability and few casting defects. Simulation results are mostly in agreement with experimental results.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.45 no.5
• /
• pp.95-102
• /
• 2008

This paper presents an appropriate approach for modeling noise in Computed Radiography(CR) images of high strength materials. The approach is specifically designed for types of noise with the statistical and nonlinear properties. CR images Ere degraded even before they are encoded by computer process. Various types of noise often contribute to contaminate radiography image, although they are detected on digitalization. Quantum noise, which is Poisson distributed, is a shot noise, but the photon distribution on Image Plate(IP) of CR system is not always Poisson process. The statistical properties are relative and case-dependant due to its material characteristics. The usual assumption of a distribution of Poisson, binomial and Gaussian statistics are considered. Nonlinear effect is also represented in the process of statistical noise model. It leads to estimate the noise variance in regions from high to low intensity, specifying analytical model. The analysis approach is tested on a database of steel tube step-wedge CR images. The results are available for the comparative parameter studies which measure noise coherence, distribution, signal/noise ratios(SNR) and nonlinear interpolation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.4
• /
• pp.343-350
• /
• 2003

Using Bi$_2$Sr$_2$Ca$_2$.$_2$Cu$_3$ $O_{x}$ powders prepared by solid state reaction and spray drying method, the nucleation and growth behaviors of superconducting and second phases were investigated during isothermal heat treatment. When the spray drying power was used in contrast with solid state reaction powder, Bi$_2$Sr$_2$Ca$_2$.$_2$Cu$_3$ $O_{x}$ (2223) phase could be formed at the relatively shot time and second phases were much bigger. Quantitative analysis showed that as the heat treatment time increased, more Bi$_2$Sr$_2$Ca$_2$.$_2$Cu$_3$ $O_{x}$ (2212) changed to 2223 and the major second phase was changed from (Sr,Ca)$_{14}$Cu$_{24}$ $O_{x}$(14:24) to (Sr,Ca)$_2$Cu$_1$ $O_{x}$ (2:l). The superconducting phase formed at the relatively short time 14:24 phase. Following the Bi-free phase of 14:24 Phase, but long time was needed in places far from the 14:24 phase. Following the formation of the 2212 phase near the 14:24 phase, the 2223 phase nucleated preferentially at the interface between the 2212 and 14:24 phases. The preferential nuclcation of 2223 was explained by its structural similarity and low Interfacial energy with both the Bi-free and 2212 Phases.12 Phases.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.1
• /
• pp.43-50
• /
• 2012

The effects of parameters related to the finite element simulation of the laser shock peening(LSP) process on the residual stresses of Inconel alloy 600 steel are discussed. In particular, we focus on the maximum pressure, pressure pulse duration, laser spot size, and number of shots. It is found that certain ranges of the maximum pressure and pulse duration can produce the maximum compressive residual stresses near the surface, and thus proper choices of these parameters are important. The residual stresses are not affected by the laser spot size, provided it is larger than a certain size. The magnitudes of the compressive residual stresses and the plastically affected depths are found to increase with an increasing number of shots, but this effect is less pronounced for more shots.

• Current Industrial and Technological Trends in Aerospace
• /
• v.9 no.1
• /
• pp.55-63
• /
• 2011

Space debris is the collection of objects in orbit around Earth that were created by humans but no longer serve any useful purpose. Since plenty of spacecrafts were launched in space after 1957, the number of space debris has been increased. According to USSTRATCOM, the number of space debris which are bigger than 10cm is more than 15,000. Recently two critical events were occurred. Which one was that China shot down their satellite using missile and the other was that t o satellite, Iridium 33 and Cosmos 2251, collided in space. Space debris environment in which KOMPSAT-2 is operating has been severe. This paper presents the status of space debris and international activity, and the comparison of conjunction assessment process between Korea Aerospace Research Institute and abroad satellite operation center.

• The Journal of Engineering Geology
• /
• v.16 no.4 s.50
• /
• pp.327-335
• /
• 2006

Three processing strategies of seismic refraction data are tested in terms of velocity and depth profiles or structures for mapping of geological discontinuities: GRM(generalized reciprocal method), GLI(generalized linear inversion), Tomography. The test data used in this study are the shot gathers reconstructed by numerical modeling for the structures of 3 planar layers(horizontal, inclined), the buried vertical fracture zones, and vertical fault zones. Tomography is shown to be very efficient for mapping of more complicated tone such as vertical fault and buried fracture zones, whereas GRM and GLI can be useful for horizontal and/or inclined layers, probably on their bases of analysis of first arrivals in travel time curves.

• Design & Manufacturing
• /
• v.11 no.3
• /
• pp.19-24
• /
• 2017

In these days, increase requirement of TEM (Transmission Electro Microscope) in not only scientific field but also industrial field. Because TEM can measure inner-structure of specimen a variety of materials like metal, bio. etc. When use TEM, specimen should be thin about 50nm. So making for thin specimen, use Ion milling device that include specimen holder. The holder generally made of Aluminium Aluminium holder is worn away easily. For this reason, using time of ion milling with aluminum holder is too short. To solve the problem, we replace aluminium holer to molybdenum alloy holder. In this paper, we design molybdenum alloy holer for CAM and modify CAD modeling for effective machining process. So we array a specimen 3 by 4 and setup orientation for one-shot machining process. Next we make a CAM program for machining. we making a decision two machining strategy that chose condition of tool-path method, step-down, step-over. etc. And then conduct machining using CNC milling machining center. To make clear difference between case.1 and case.2, we fixed machining conditions like feed-rate, main spindle rpm, etc. After machining, we confirm the condition of workpiece and analysis the problems case by case. Finally, case.2 work piece that superior than case.1 cutting with WEDM because that method can not ant mechanical effect on workpiece.