• Journal of Ecology and Environment
• /
• v.30 no.2
• /
• pp.201-207
• /
• 2007

Researchers have used a variety of methods to measure patterns of animal movement, including the use of spatial data (mapping the position of a moving animal at specified intervals) and direct estimation of travel path length by pacing under a moving animal or group. I collected movement data from five groups of siamangs (Symphalangus syndactylus) using two different methods concurrently to estimate the effects of the method of data collection on estimates of daily path length (DPL). Estimates of DPL produced from spatial data collected at 15-minute intervals were 12% lower than estimates of DPL produced by pacing under the traveling animal. The actual magnitude of the difference was correlated with the travel distance, but there was no correlation between the proportional difference and the travel distance. While the collection of spatial data is generally preferable, as spatial data permit additional analyses of patterns of movements in two or three dimensions, the relatively small difference between the DPL's produced using different methods suggests that pacing is an acceptable substitute where the collection of spatial data is impractical. I also subsampled the spatial data at increasing time intervals to assess the effect of sampling interval on the calculation of daily path lengths. Longer sampling intervals produced significantly shorter estimates of travel paths than shorter sampling intervals. These results suggest that spatial data should be collected at short time intervals wherever possible, and that sampling intervals should not exceed 30 minutes. Researchers should be cautious when comparing data generated using different methods.

• Korean Journal of Applied Biomechanics
• /
• v.16 no.2
• /
• pp.135-144
• /
• 2006

This study was to investigate the kinematic analysis to score of the Yurchenko stretch skill according to phases in a horse vaulting. For this study, 8 male national gymnasts were participated in acquiring three dimensional kinematical imagining data with four Sony PD-150 video cameras After digitizing motion, the Direct Linear Transformation(DLT) technique was employed to obtain 3-D position coordinates. The kinematic factors of the distance, velocity and angle variable were calculated for Kwon3D 3.1. The following conclusions were drawn; 1) The COG resultant velocity of the less skilled group decreased in PRF phase because the less skilled group had a larger flexion-knee angle than the skilled group in BC phase, Because the less skilled group had larger flexion-shoulder angle than the skilled group in HTO phase, At blocking movement, the body inclined a moving direction. By means of it, COG lowered 2) The skilled group had a more rapid COG's vertical velocity than the less skilled group at HTD and HTO event in HC phase, because this was performed the blocking movement with body angle and contacted on a horse vaulting small and its time short by means of contacting hands on a horse vaulting quickly. Such blocking movement made the vertical up-flight movement easy at POF phase bringing out rapid COG's vertical velocity after take off a horse vaulting.

• The korean journal of orthodontics
• /
• v.45 no.4
• /
• pp.180-189
• /
• 2015

Objective: To compare the positions of the mandibular premolars in Angle Class I subjects according to vertical facial type. The results will provide a theoretical basis for predicting effective tooth movement in orthodontic treatment. Methods: Cephalometric parameters were determined using cone-beam computed tomography in 120 Angle Class I subjects. Subjects were categorized as short, normal, and long face types according to the Frankfort mandibular angle. Parameters indicating the position of the mandibular right premolars and the mandible were also measured. Results: The angle between the mandibular first premolar axis and buccal cortex, the distance between the root apex and buccal cortex, angle of vestibularization, arc of vestibularization, and root apex maximum movable distance were significantly greater in the short face type than in the long and norm face types. The angle between the mandibular second premolar axis and buccal cortex, the distance from root apex to buccal cortex, and the arc of vestibularization were significantly greater in the short face type than in the normal face type. Conclusions: There are significant differences in the mandibular premolar positions in Class I subjects according to vertical facial type.

• PNF and Movement
• /
• v.17 no.2
• /
• pp.177-187
• /
• 2019

Purpose: The purpose of this study was to investigate the effects of combined training on the physical fitness of male short distance athletes. Methods: Combined training was applied with CLT and isokinetric training three times a week for eight weeks. For CLT, elastic bands were used in the sitting and standing positions to gradually increase sprint and skating movements. Isokinetic training was conducted at $60^{\circ}/sec$ and $180^{\circ}/sec$ to improve muscle strength and muscle power. Results: After the application of combined training, strength (hand force) improved from 42.25 kg to 47.30 kg. Muscle power for standing long jump improved from 240.00 cm to 248.80 cm, while the sergeant jump improved from 55.00 cm to 58.00 cm. Isokinetic testing showed that muscle strength ($60^{\circ}/sec$) improved from 315.65 %BW to 365.79 %BW for the left extensor and from 306.60 %BW to 325.00 %BW for the right extensor. The left flexor improved from 177.23 %BW to 189.47 %BW, but the right flexor decreased slightly from 210.87 %BW to 201.53 %BW. Muscle power ($180^{\circ}/sec$) improved from 254.00 %BW to 293.00 %BW for the left extensor and from 256.00 %BW to 272.00 %BW for the right extensor. The left flexor improved from 150.00 %BW to 162.00 %BW and the right flexor from 145.25 %BW to 182.00 %BW. Conclusion: Combined training could be used as a physical training program for male short distance athletes.

• Korean Journal of Applied Biomechanics
• /
• v.17 no.1
• /
• pp.91-97
• /
• 2007

The purpose of this study was to investigate the changes of various balls velocity under the different surface conditions after impact. For this study, four different balls were used which are golf ball, tang-tang ball, table tennis ball, and iron ball. And two different types of ground conditions were used which are artificial grass green and glass green. Movements of putter head and ball were recorded with 2 HD video cameras(60 Hz, 1/500s shutter speed). Small size control object($18.5cm{\times}18.5cm{\times}78.5cm$) was used in this study. To transfer the same amount of kinetic energy to the ball, pendulum putting machine was used. Analyzing the process of impact and the ball movement, a putter was digitized the whole movement but the ball was digizited within the 50cm movement. Velocities were calculated by the first central difference method(Hamill & Knutzen, 1995). Putter head velocities were about 112.2cm/s-116.2cm/s at impact. Maximum ball velocities were appeared 0.08s-0.10s after impact no matter what the ground conditions are. Table tennis ball recorded higher ball velocities than the other ball velocities and iron ball recorded the lowest ball velocity in this group. But Table tennis ball was influenced with the frictional force and immediately was decreased at the artificial grass green condition. If an object is received the kinetic energy under the static condition(v=0cm/s), the object recorded the maximum velocity shortly after the impact and then decreased the velocity because of the frictional force. The ball distance from the start position to the peak velocity position is about 6cm-10cm under the 112.2cm/s-116.2cm/s putting velocity with putter. 0.25 seconds later after impact balls were placed 40cm distance from the original position except iron ball. In this study, ball moving distances were too short therefore it was not possible to investigate the reactions after the translational force is disappeared. Rotational force would play a major role at the end of the ball movement. Future study must accept two things. One is long distance movement of ball and the other is balanced ground. Three-piece ball is a good item to investigate the golf ball movement on the different surface conditions.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.1
• /
• pp.195-205
• /
• 2013

This study, using the MCC Model to consider consolidation, estimated the range within which no influences occur from lateral movement and its amount of the foundation pile and abutment on the soft ground. This study performed finite element analyses, with variations on the adhesiveness and internal friction angle, depth of soft clay, embankment height, consolidation parameters, and separation distance between the abutment and embankment. The abutment's horizontal displacement exhibits linear change with a longer separation distance, and changes into an exponential form as the embankment gets closer to the abutment. As the soft clay layer becomes 10 m deeper, the horizontal displacement tends to increase 1.5~3.0 times. However, it decreases at a rate of 0.3~0.95 when adhesiveness is increased by 10 $kN/m^2$ and internal friction angle is increased by $5^{\circ}$. The increase change rate in a lateral movement amount becomes greater if it is closer to the abutment when the abutment separation distance is long. When the distance is short, the change rate of horizontal displacement increases in similar a way, but it tends to be decreasing overall.

• Korean Journal of Applied Biomechanics
• /
• v.13 no.3
• /
• pp.81-98
• /
• 2003

The purpose of this study is to closely examine kinematic characteristics by jump phase of Li Xiaopeng motion in horse vaulting and provide the training data. In doing so, as a result of analyzing kinematic variables through 3-dimensional cinematographic using the high-speed video camera to Li Xiaopeng motion first performed at the men's vault competition at the 14th Busan Asian Games, the following conclusion was obtained. 1. It was indicated that at the post-flight, the increase of flight time and height and twisting rotational velocity has a decisive effect on the increase of twist displacement. And Li Xiaopeng motion showed longer flight time and higher flight height than Ropez motion with the same twist displacement of entire movement. Also the rotational displacement of the trunk at peak of COG was much short of $360^{\circ}$(one rotation) but twist displacement showed $606^{\circ}$. Likewise, Li Xiaopeng motion was indicated to concentrate on twist movement in the early flight. 2. It was indicated that at the landing, Li Xiaopeng motion gets the hip to move back, the trunk to stand up and the horizontal velocity of COG to slow down. This is thought to be the performance of sufficient landing, resulting from large security of rotational displacement of airborne and twist displacement. 3. It was indicated that at the board contact, Li Xiaopeng motion made a rapid rotation uprighting the trunk to recover slowing velocity caused by jumping with the horse in the back, and has already twisted the trunk nearly close to $40^{\circ}$ at board contact. Under the premise that elasticity is generated without the change of the feet contacting the board, it will give an aid to the rotation and twist of pre-flight. Thus, in the round-oH phase, the tap of waist according to the fraction and extension of hip joint and arm push is thought to be very important. 4. It was indicated that at the pre-flight, Li Xiaopeng motion showed bigger movement than the techniques of precedented studies rushing to the horse, and overcomes the concern of relatively low power of jump through the rapid rotation of the trunk. Li Xiaopeng motion secured much twist distance, increased rotational distance with the trunk bent forward, resulting in the effect of rushing to the horse. 5. At horse contact, Li Xiaopeng motion makes a short-time contact, and maintains horse take-off angle close to vertical, contributing to the increase of post-flight time and height. This is thought to be resulted from rapid move toward movement direction along with the rotational velocity of trunk rapidly earned prior to horse contact, and little shave of rotation axis according to twist motion because of effective twist in the same direction.

• Journal of Information Technology Services
• /
• v.20 no.6
• /
• pp.83-95
• /
• 2021

In this study, various usage patterns were analyzed after establishing a data mart for micro mobility analysis based on the rental history of public bicycles in Seoul. Rental history data is origin-destination data that includes the rental location and time, and the return location and time. About 1500 rental locations were classified according to the characteristics of the location to create a 'station type' dimension. We also created a 'path type' dimension that displays whether the rental location and return location are the same. In addition, a derived variable called speed, which is obtained by dividing the distance used by the time used, is added, and through this, the characteristics of the riding area and the reason for the rental can be estimated. Meanwhile, administrative district link, administrative neighborhood link, and station type link were created to apply network analysis. Through this analysis, the roles and proportions of administrative districts, public facilities, and private facilities engaged in micro-mobility services were visualized. 49.9% of rentals occur at rental offices near transportation facilities, and half of them occur at rental offices near subway stations. The number of rentals during the evening rush hour is more than double that of the morning rush hour. When the path type is unidirectional, there is a fixed destination, so the distance and time used are short, and the movement speed tends to be high. In the case of round-trip, the purpose of use is exercise or leisure, so the distance and time used are long, and the movement speed is slow. It is expected that the results of the analysis can be used as reference materials for selecting new rental locations, providing convenient services for users, and developing user-specialized products.

• Journal of Biosystems Engineering
• /
• v.35 no.1
• /
• pp.37-45
• /
• 2010

Since SRC (Short-term Rotation Coppice) such as poplar and willow can be harvested in three years, they are known to be a potential forest biomass as fuel for a power plant. The production system including transplanting and harvesting is, however, necessary to be mechanized because such a biomass should be handled in a massive volumetric size. A pull-type stem-cutting transplanter was developed in the research as the first step to realize the production of SRC. A needle-like transplanting device pushes a stem-cutting into the prepared soil bed by a pneumatic cylinder, and another device firms soil around a stem-cutting transplanted. Since this is an intermittent operation, it was necessary to develop a zero horizontal velocity mechanism which enabled only the transplanting needle part to continue a zero horizontal movement relative to the ground during the transplanting operation even when the tractor kept moving forward. The 2-row transplanter can transplant stem-cuttings at the rate of 6.5 seconds per row without missing a single attempt. The planting depth and distance were well maintained and controlled. Their CVs were between 2.1~3.4% and 0.87~1.7% for the depth and the distance, respectively. Although, the transplanted stem-cuttings tended to lean outward from the back-view and forward from the side view, they were planted within the range of $3^{\circ}$ from the upright position.

• Korean Institute of Interior Design Journal
• /
• v.26 no.2
• /
• pp.22-32
• /
• 2017

This research is to analyze the spatial information search features which shown by Eye fixation and movement and conducted eye tracking experiment for targeting sports shop spatial images which it are same but looks different. This is able to find out the eye movement feature according to placement of goods from the eye movement and movement distance of spatial visitor, and the result can be defined as following. First, the whole original-reverse left / right images have a higher number of observations in the [IN] area than in the [OUT] area. This is because after eye taking high observations in LA area of [IN] have been jump-over [OUT], performed search activities in low eye fixation without high eye fixation. Second, there was a difference in the frequency of the observation data as the composition of the images changed. The original image has been often fixed the eyes in LA area, and the one that has been observed for a long time is reverse left / right image. Also, fixation point was shown higher at the reverse left / right image as jump-over from [OUT] area to [IN] area. If LA area seen as reverse left / right image, it is located in right-hand side. The case where the dominant area is on the right side has a characteristic that the eye fixation is longer. This can be understand that the arrangement of products for attract the customer's attention in the commercial space might be more effective when it is on the right side. Third, the moving distance(IN ${\rightarrow}$ OUT) of the sight pointed to external from LA area was long in the both original-reverse left / right images, but it is no relation with search direction([IN${\rightarrow}$OUT] [IN${\rightarrow}$OUT]) of the sight. In other words, the sight that entered in LA area can be seen as visual perception activity for re-searching after big jump-over, in the case go in to outward (OUT area) after searching for more than certain time. The fact that the moving distance of eye is relatively short in the [IN ${\rightarrow}$ OUT] process considered as that the gaze that stays outside the LA area naturally enters in to LA area.