• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.6
• /
• pp.4245-4252
• /
• 2015

In this study, an experiment which utilized glass fiber reinforced polymer(GFRP) plank as the permanent formwork of cast-in-place high strength concrete structures was performed. The GFRP plank currently being produced has smooth surface so that it causes problems in behavior with concrete. Therefore, this research analyzed the flexure/shear failure behavior of composite beams, which used GFRP plank as its permanent formwork and has short shear span ratio, by setting the sand coated at GFRP bottom surface, the perforation and interval of the GFRP plank web, and the width of the top flange as the experimental variables. As a result of the experiments for effectiveness of sand attachment in case of not perforated web, approximately 47% higher ultimate load value was obtained when the sand was coated than not coated case and bending/shear failure mode was observed. For effectiveness of perforation and interval of gap, approximately 24% higher maximum load value was seen when interval of the perforation gap was short and the fine aggregate was not coated, and approximately 25% lower value was observed when the perforation gap was not dense on the coated specimen. For effectiveness of top flange breadth, the ultimate load value was approximately 17% higher in case of 40mm than 20mm width.

• Korean Journal of Materials Research
• /
• v.9 no.3
• /
• pp.315-321
• /
• 1999

Metal matrix composites have been extensively studied because of their excellent characteristics for structural application. $Al_2O_3$ and SiC have been used as a common reinforcement owing to their good mechanical properties. However the manufacturing cost of these ceramic reinforcement is expensive, so the use of the composites has been restricted to special purposes. In this study, we tested the application possibility as a reinforcement of $Al_2O_3$-TiC powder synthesized by SHS(Self-propagating High-temperature Synthesis) process to Al alloy matrix composite. Also, $Al_2O_3$ short fibers were added with the synthesized powders in order to apply to the Al matrix hybrid composites. Squeeze infiltration casting process was used to make the composite with 25vol% of reinforcement. Microstructure and crystal structure were examined by SEM, OM and XRD, also the mechanical properties were studied by the compressive test and wear test.

• Korean Journal of Exercise Nutrition
• /
• v.16 no.2
• /
• pp.65-71
• /
• 2012

Oxygen is the final acceptor of electron transport from fat and carbohydrate oxidation, which is the rate-limiting factor for cellular ATP production. Under altitude hypoxia condition, energy reliance on anaerobic glycolysis increases to compensate for the shortfall caused by reduced fatty acid oxidation [1]. Therefore, training at altitude is expected to strongly influence the human metabolic system, and has the potential to be designed as a non-pharmacological or recreational intervention regimen for correcting diabetes or related metabolic problems. However, most people cannot accommodate high altitude exposure above 4500 M due to acute mountain sickness (AMS) and insulin resistance corresponding to a increased levels of the stress hormones cortisol and catecholamine [2]. Thus, less stringent conditions were evaluated to determine whether glucose tolerance and insulin sensitivity could be improved by moderate altitude exposure (below 4000 M). In 2003, we and another group in Austria reported that short-term moderate altitude exposure plus endurance-related physical activity significantly improves glucose tolerance (not fasting glucose) in humans [3,4], which is associated with the improvement in the whole-body insulin sensitivity [5]. With daily hiking at an altitude of approximately 4000 M, glucose tolerance can still be improved but fasting glucose was slightly elevated. Individuals vary widely in their response to altitude challenge. In particular, the improvement in glucose tolerance and insulin sensitivity by prolonged altitude hiking activity is not apparent in those individuals with low baseline DHEA-S concentration [6]. In addition, hematopoietic adaptation against altitude hypoxia can also be impaired in individuals with low DHEA-S. In short-lived mammals like rodents, the DHEA-S level is barely detectable since their adrenal cortex does not appear to produce this steroid [7]. In this model, exercise training recovery under prolonged hypoxia exposure (14-15% oxygen, 8 h per day for 6 weeks) can still improve insulin sensitivity, secondary to an effective suppression of adiposity [8]. Genetically obese rats exhibit hyperinsulinemia (sign of insulin resistance) with up-regulated baseline levels of AMP-activated protein kinase and AS160 phosphorylation in skeletal muscle compared to lean rats. After prolonged hypoxia training, this abnormality can be reversed concomitant with an approximately 50% increase in GLUT4 protein expression. Additionally, prolonged moderate hypoxia training results in decreased diffusion distance of muscle fiber (reduced cross-sectional area) without affecting muscle weight. In humans, moderate hypoxia increases postprandial blood distribution towards skeletal muscle during a training recovery. This physiological response plays a role in the redistribution of fuel storage among important energy storage sites and may explain its potent effect on changing body composition. Conclusion: Prolonged moderate altitude hypoxia (rangingfrom 1700 to 2400 M), but not acute high attitude hypoxia (above 4000 M), can effectively improve insulin sensitivity and glucose tolerance for humans and antagonizes the obese phenotype in animals with a genetic defect. In humans, the magnitude of the improvementvaries widely and correlates with baseline plasma DHEA-S levels. Compared to training at sea-level, training at altitude effectively decreases fat mass in parallel with increased muscle mass. This change may be associated with increased perfusion of insulin and fuel towards skeletal muscle that favors muscle competing postprandial fuel in circulation against adipose tissues.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.23 no.2
• /
• pp.121-128
• /
• 2003

This study was conducted to investigate the effect of tall type mixtures and tall+short type mixtures on dry matter yield, botanical composition and quality. The experimental design includes two mixture types: Tall type mixtures(TM); orchardgrass(Potomac) 40+tall fescue(Fawn) 20+Festulolium braunii (Paulita) 10+perennial ryegrass(Reveille) 10+timothy(Climax) 10+red clover(Kenland) 5+alfalfa(Vernal) 5%) and tall+short type mixtures(TSM); orchardgrass(Potomac) 40+tall fescue(Fawn) 20+Kentucky bluegrass(Newport, turf type) 10+redtop(Barricuda, turf type) 10+perennial ryegrass(Palmer III, turf type) 10+red fescue(Flyer II, turf type) 5+white clover(Regal) 5%. The dry matter(DM) yield was higher obtained in TSM than that of TM, but there was no significant difference between TM and TSM. In the chemical composition, there was no significant difference between TM and TSM, but the content of cellulose, lignin were higher in TM than those in TSM(p<0.05). Also, the content of acid detergent fiber which affected dry matter digestibility was higher in TM than that of TSM. The crude protein dry matter yield was not observed significant difference between TM and TSM, but digestible dry matter(DDM) yield was higher in TSM than that of TM. In botanical composition, tall fescue, alfalfa and orchardgrass were highly maintained in TM but white clover, tall fescue and orchardgrass were highly, and redtop, red fescue were continuously maintained in TSM. In this experiment, DM yields and quality of two mixture types were no difference. However, the tall+short type mixtures(TSM) were more effective in enhancing the dry matter digestibility and DDM yield, and in maintaining the various botanical composition.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.16 no.3
• /
• pp.290-302
• /
• 1994

This study was aimed to clarify the histopathological changes in the experimental animal model subjcted to rigid fixation performed across the frontonasal sutrue in growing rabbits. Sixteen rabbits aged 6 weeks used. In experimental group(n=12), rigid fixation with miniplates and screws was performed across the frontonasal suture. Control group(n=4) was those with periosteal elevation only. Experimental animals were sacrificed on the 2nd, 4th, 8th, and 12th week after operation, and frontonasal suture area was excised for light microscopic and scanning electron microscopic examination. The results obtained were as follows : 1. In control groups, collagen fiber bundles ran in the midportion of bone sutrue and cambial layers were seen at bone surface. Sutural surfaces are beveled and external and internal bony projected portions were observed. 2. In experimental groups, distance of bone suture was decreased by new bone formation on the 2nd week, while increased by bone resorption at the miniplate applied area and bone formation in the adjacent bone on the 4th week. 3. In experimental groups, the original bone surface was almost resorbed and new bone formation was found on the 8th week. Regulary-run collagen fibers, smooth and dense bone surfaces were similar to the bone patterns of control groups on the 12th week. Above results suggest that bone formation is restricted where the miniplate is applied, while compensatory growth is appeared in the adjacent bont. It is considered that rigid fixation with miniplates and acrews results in a little disturbance of sutural growth of the craniofacial bone in infancy and children when applied for short duration.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.6
• /
• pp.88-95
• /
• 2020

Currently, Fiber-Reinforced Plastic (FRP) composite materials are used in many industrial fields, owing to their superior stiffness and specific strength compared to metals. However, there are issues with FRP inefficiency, due to low productivity of such materials, environmental problems they pose and long curing times needed. Trying to address these issues, research was conducted towards the development of a FRP composite material with excellent properties and short production time, introducing a curing method using a UV lamp. Four types of composite materials were prepared, cured with catalyst or UV (CZ: Catalyst + ZNT 6345, CR: Catalyst + RF 1001 MV, UVZ: Photoinitiator + ZNT 6345, and UVR: Photoinitiator + RF 1001 MV). Examination of the chemical and mechanical properties of these composites showed that UV-cured materials performed better than the catalyst-cured ones. These results indicate that the production process of FRP composite materials can be simplified by using a UV lamp for curing, resulting in composite materials with the same quality, but reduced production time by about 70% compared to currently used practices. This advancement will contribute greatly to the composite material industry.

• Restorative Dentistry and Endodontics
• /
• v.27 no.6
• /
• pp.587-599
• /
• 2002

Extracellular single unit recordings were made from the ventral posteromedial thalamic (VPM) nociceptive neurons to determine mechanoreceptive field (RF) and response properties. A total of 44 VPM thalamic nociceptive neurons were isolated from rats anesthetized with urethane-chloralose. Based on responses to various mechanical stimuli including touch, pressure and pinch applied to the RF, 32 of 44 neurons were classified as nociceptive specific (NS) neuron. The other 12 neurons, classified as wide dynamic range (WDR), showed a graded response to increasingly intense stimuli, with a maximum discharge to noxious pinch. The VPM nociceptive neurons showed various spontaneous activity ranged from 0-6 Hz. They were located throughout the VPM, and had an contralateral RF including mainly intraoral (and perioral) regions. The RF size was relatively small, and very few neurons had a receptive field involving 3 trigeminal divisions. The NS neurons activated only by pressure and pinch stimuli had high mechanical thresholds compared to WDR neurons activated also by touch stimuli. The VPM nociceptive neurons were tested with suprathershold graded mechanical stimuli. Most of 21 NS and 8 WDR neurons showed a progressive increase in number of spikes as mechanical stimulus intensity was increased. In some neurons, the responses reached a peak before the highest intensity was given. Application of 5 mM $CoCl_2{\;}(10{\;}{\mu}\ell)$ solution to the trigeminal subnucleus caudalis did not produce any significant changes in the spontaneous activity, RF size, mechanical threshold, and response to suprathreshold mechanical stimuli of 9 VPM nociceptive neurons tested. 17 of 33 VPM nociceptive neurons responded to noxious heat as well as noxious mechanical stimuli applied to their RF. Application of the mustard oil, a small-fiber excitant and inflammatory irritant, to the right maxillary first molar tooth pulp induced an immediate but short-lasting neuronal discharges upto approximately 4 min in 16 of 42 VPM nociceptive neurons. These results suggest that VPM thalamic nucleus may contribute to the sensory discriminative aspect of orofacial nociception.

• Journal of Periodontal and Implant Science
• /
• v.30 no.3
• /
• pp.609-619
• /
• 2000

Cyclosporin A(CsA) is now widely used to treat organ transplant recipients. But CsA has various short-and long-term side effects. Especially, gingival hyperplasia is not easy to resolve since its nature is still unknown. This study discusses the pathogenesis of CsA-induced gingival hyperplasia on the basis of data obtained from light and electron microscopic studies of biopsis from patients on CsA treatment after kidney transplantation. Light microscopically, the multilayered squamous epithelium showed an irregular surface of parakeratosis and deep invaginations in the subepithelial tissue. At lamina propria, we observed bundles of irregularly arranged collagen fiber, some fibroblasts, numerous capillary vessels and a large diffuse infiltration of plasma cells. Ultrastructurally, many fibroblasts, collagen fibers, collagen fibrils were present in lamina propria. On the basis of the data collected, we propose that the morphological features of the dimensional increase in gingival tissue associated with CsA treatment in kidney transplant patients may be considered proliferative fibroblasts, collagen fibers, collagen fibrils in lamina propria.

• Journal of Nutrition and Health
• /
• v.35 no.9
• /
• pp.912-918
• /
• 2002

In nature, two different types of fructose polymers (fructan) are generally found in dietary fibers; these are the fructose homopolymers levan, which is of high molecular weight and is $\beta$-(2,6)-linked, and inulin, which is of low molecular weight and is $\beta$-(2,1)-linked. The effects of levan and inulin on the intestinal physiology of rats were compared. Sprague Dawley rats were fed one of three diets for 3 weeks: a control diet, a basal diet containing 7% of levan, and a basal diet containing 7% of inulin. Cecal enlargement, together with the lowering of cecal pH, occurred in rats fed on the levan and inulin diets (p < 0.05). The levan and inulin diets resulted in a two-fold increase in the amount of short-chain fatty acids in the cecum, when compared to the control diet. The number of total microbes and of lactic acid-producing bacteria in the feces were higher in rats fed the fructan diets than those in rats fed control diet (p < 0.05). The levan diet also significantly increased the cecal $\alpha$-galactosidase activity by 3.8-fold, when compared to the control diet, indicating that levan stimulated the growth of Bifidobacteria in the cecum. These results show that the intake of levan and inulin stimulated the growth of lactic acid-producing bacteria in the cecum and thereby improved intestinal conditions in rats. (Korean J Nutrition 35(9) : 912~918,2002)

• Smart Structures and Systems
• /
• v.21 no.1
• /
• pp.53-64
• /
• 2018

Nondestructive testing methods are required to assess the condition of civil structures and formulate their maintenance programs. Axial force identification is required for several structural members of truss bridges, pipe racks, and space roof trusses. An accurate evaluation of in situ axial forces supports the safety assessment of the entire truss. A considerable redistribution of internal forces may indicate structural damage. In this paper, a novel compressive force identification method for prismatic members implemented using static deflections is applied to steel beams. The procedure uses the Euler-Bernoulli beam model and estimates the compressive load by using the measured displacement along the beam's length. Knowledge of flexural rigidity of the member under investigation is required. In this study, the deflected shape of a compressed steel beam is subjected to an additional vertical load that was short-term measured in several laboratory tests by using fiber Bragg grating-differential settlement measurement (FBG-DSM) sensors at specific cross sections along the beam's length. The accuracy of midspan deflections offered by the FBG-DSM sensors provided excellent force estimations. Compressive load detection accuracy can be improved if substantial second-order effects are induced in the tests. In conclusion, the proposed method can be successfully applied to steel beams with low slenderness under real conditions.