• Steel and Composite Structures
• /
• v.45 no.1
• /
• pp.147-157
• /
• 2022

This study assessed the compressive and tensile strengths and modulus of elasticity of waste polyethylene terephthalate (PET) using the ASTM standard tests. In addition, short carbon and glass fibers were mixed with waste PET to examine the improvements in ductility and strength during compression. The bonding was examined via field-emission scanning electron microscopy. The strength degradation of the waste PET tested under UV was 40-50%. However, it had a compressive strength of 32.37 MPa (equivalent to that of concrete), tensile strength of 31.83 MPa (approximately ten times that of concrete), and a unit weight of 12-13 kN/m3 (approximately half that of concrete). A finite element analysis showed that, compared with concrete, a waste PET pile foundation can support approximately 1.3 times greater loads. Mixing reinforcing fibers with waste PET further mitigated this, thereby extending ductility. Waste PET holds excellent potential for use in foundation piles, especially while mitigating brittleness using short reinforcing fibers and avoiding UV degradation.

• Proceedings of the Korean Fiber Society Conference
• /
• 1997.10a
• /
• pp.477-480
• /
• 1997

• Steel and Composite Structures
• /
• v.27 no.2
• /
• pp.193-200
• /
• 2018

This paper presents an experimental work for short circular steel tube columns filled with normal concrete (NAC), recycled aggregate concrete (RAC), and RAC with silica fume and steel fiber. Ten specimens were tested under axial compression to research the effect of silica fume and steel fiber volume percentage on the behavior of recycled aggregate concrete-filled steel tube columns (RACFST). The failure modes, ultimate loads and axial load- strain relationships are presented. The test results indicate that silica fume and steel fiber would not change the failure mode of the RACFST column, but can increase the mechanical performances of the RACFST column because of the filling effect and pozzolanic action of silica fume and the confinement effect of steel fiber. The ultimate load, ductility and energy dissipation capacity of RACFST columns can exceed that of corresponding natural aggregate concrete-filled steel tube (NACFST) column. Design formulas EC4 for the load capacity NACFST and RACFST columns are proposed, and the predictions agree well with the experimental results from this study.

• Composites Research
• /
• v.24 no.4
• /
• pp.41-47
• /
• 2011

This paper deals with anisotropic property and structural analysis for short fiber reinforced plastic composites manufactured by the injection molding process. The common approach for modeling this type of material is the consideration of the material as homogenous and isotropic. However, the common isotropy approach often results in unexpected failure. To overcome this, new structure analysis methodology was developed in order to consider fiber orientation effect using injection mold flow analysis and Halpin-Tsai equations for unidirectional composites and taking an orientation average. The numerical predictions are compared to experimental data for tensile specimen. The predicted mechanical properties agree well with experimental data for fiber orientation and weld line effect. The analysis system was also applied to an automobile part. The proposed anisotropic model predicted different mechanical properties by position of the part and different mechanical performance of the part was changed according to injection gate position.

• Korean Journal of Optics and Photonics
• /
• v.16 no.6
• /
• pp.494-499
• /
• 2005

We have demonstrated a fiber short-wavelength filter with a good cut-off property using dissimilar dispersive properties between? a thermally expanded cored fiber and an external medium. Side-polishing is applied to coupling between the fiber and the external medium. The experimental results revealed that the bend edge wavelength can be adjusted by controlling the degree of core expansion. Futhermore, the sharpness of wavelength response? was significantly? improved by employing expanded core fiber instead of a conventional single mode fiber. Tuning range of the band edge wavelength exceeded 400 m based on thermo-optic effect of the external medium.

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.3
• /
• pp.310-320
• /
• 2007

Statement of the problem. The fracture of acrylic resin dentures remains an unsolved problem. Therefore, many investigations have been performed and various approaches to strengthening acrylic resin, for example, the reinforcement of heat-cured acrylic resin using glass fibers, have been suggested over the years. But problems such as poor workability, rough surface, poor adhesion of glass fiber resin complex are not solved yet. Purpose. The aim of the present study was to investigate the effect of short glass fibers on the transverse strength of heat-polymerized denture base acrylic resin and roughness of resin complex after abrasion test. Material and methods. To avoid fiber bunching and achieve even fiber distribution, glass fiber bundles were mixed with acrylic resin powder in conventional mixer with a non-cutting blade, to produce the glass fiber($10{\mu}m$ diameter, 3mm length, silane treated) resin composite. Glass fibers were incorporated at 0%, 3%, 6% and 9% by weight. Transverse strength were measured. After abrasion test, surface roughness was evaluated and scanning electron microscope view was taken for clinical application. Results. 1. 6% and 9% incorporation of 3mm glass fibers in the acrylic resin enhanced the transverse strength of the test specimens(p<0.05). 2. Before abrasion test, incorporation of 0%, 3%, 9% glass fiber in the resin showed no dirrerence in roughness statisticaly(p>0.05). 3. After abrasion test, incorporation of 0%, 3%, 6% glass fiber in the resin showed same surface roughness value statistically(p>0.05). 4. In SEM, surface roughness increased as the percentage of the fibers increased. 5. In the areas where glass fiber bunchings are formated, a remarkably high roughness was noticed. Conclusion. 6% and 9% addition of silane-treated short glass fibers into denture base acrylic resin increased transverse strength significantly. Before and after abrasion test, incorporation of 0%, 3%, 6% glass fiber in the resin showed same surface roughness value statistically.

• Journal of Korean Academy of Nursing
• /
• v.25 no.2
• /
• pp.193-209
• /
• 1995

The purpose of this study was to determine the effect of intermittent low - intensity, short duration exercise during hindlimb suspension on the mass, relative weight, myofibrillar protein content, cross-sectional area of Type I and Type II fibers and SDH activity in Type II(plantaris) muscle. To examine the effectiveness of intermittent low-intensity, short duration exercise on mass, myofibrillar protein content and fiber size, the hindlimbs of adult female Wistar rats were suspended(HS) and half of these rats walked on a treadmill for 45 min/day(9 min every 2h) at 5m /min and a 15$^{\circ}$grade (HS-EX). Plantaris wet weight was 19.67% significantly smaller(p<0.005) and relative plantaris weight was 6.25% smaller compared with those of control rats following seven days of hindlimb suspension. Plantaris wet weight and relative plantaris weight increased by 27.66%, 12.22% each through intermit-tent exercise during hindlimb suspension(p<0.005, p<0.05), moreover, plantaris wet weight and relative plantaris weight of the HS-EX rats were similar to those of control rats. Soleus wet weight and relative soleus weight decreased significantly by 31% and 22.0% in the HS rats(p<0.05). Soleus wet weight and relative soleus weight increased by 10.41%, 25.64% respectively through intermittent ex-ercise during hindlimb suspension, furthermore, soleus wet weight and relative weight of the HS-EX rats were closer to those of control rats. Myofibrillar protein content of plantaris and soleus decreased significantly by 51.49%, 59.65% each, following seven days of hindlimb suspension (p<0.005) Myofibrillar protein content of plantaris and soleus increased by 51.79%, 75.47% each with significance through intermittent exercise during hindlimb suspension(p<0.005). Myofibrillar protein content of plantaris and soleus in HS-EX rats was smaller than that of control rats. No change was observed in fiber type percentage following 1 week of hindlimb suspension or exercise during hindlimb suspension. The type I fiber cross-sectional area of both soleus and plantaris muscle was 18.72% and 41.07% lower in the HS than that of the controls (p<0.05, p<.001), that of both muscles was 6.60% and 29. 3％ greater in the HS-EX than that of the HS rats. HS plus intermittent low- intensity short duration exercise resulted in Type I fiber cross-sectional area closer to the controls. Type II fiber cross-sectional area of both plantaris and soleus muscle was 22.45% and 22.58% sl nailer in the HS than in the controls, that of both muschles in the HS-EX was 14.10%, 5.78% greater than HS. Intermittent exercise during hindlimb suspension resulted in Type I, II fiber cross-sectional area closer to the control value. There was no change in SDH activity following 1week of hindlimb suspension or exercise during hindlimb suspension in the plantaris muscle. The results suggest that intermittent low intensity short duration exercise can ameliorate Type II muscular atrophy Induced by hindlimb suspension.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.6
• /
• pp.791-796
• /
• 2013

In this study, the mechanical properties of a carbon fiber/polypropylene composite were evaluated according to the carbon fiber surface treatment. Carbon fiber surface treatments such as silane coupling agents and plasma treatment were performed to enhance the interfacial strength between carbon fibers and polypropylene. The treated carbon fiber surface was characterized by XPS, SEM, and single-filament tensile test. The interlaminar shear strength (ILSS) of the composite with respect to the surface treatment was determined by a short beam shear test. The test results showed that the ILSS of the plasma-treated specimen increased with the treatment time. The ILSS of the specimen treated with a silane coupling agent after plasma treatment increased by 48.7% compared to that of the untreated specimen.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.4C
• /
• pp.213-220
• /
• 2008

A study on cemented sand reinforced with short fibers was carried out to improve its unconfined compressive strength and brittle behavior. Nak-dong River sand was mixed with Portland cement and polyvinyl alcohol (PVA) fibers. A PVA fiber widely used for concrete reinforcement is randomly distributed into cemented sand. Nak-dong River sand, cement and fibers with optimum water content were compacted in 5 layers and then cured for 7 days. The effect of fiber reinforcement rather than cementation was emphasized by using a small amount of cement. Weakly cemented sand with a cement/sand ratio less than 8% was fiber-reinforced with different fiber ratios and tested for unconfined compression tests. The effect of fiber ratio and cement ratio on unconfined compressive strength was investigated. Fiber-reinforced cemented sand with 2% cement ratio showed up to six times strength to non-reinforced cemented sand. Because of ductile behavior of fiber-reinforced specimens, an axial strain at peak stress of specimens with 2% cement ratio increases up to 7% as a fiber ratio increases. The effect of 1% fiber addition into 2% cemented sand on friction angle and cohesion was analyzed separately. When the fiber reinforcement is related to friction angle increase, the 8% of applied stress transferred to 1% fibers within specimens.

• Composites Research
• /
• v.13 no.1
• /
• pp.50-60
• /
• 2000

This paper presents an analytical method considering tensile strength enhancement in hybrid $Al_2O_3$ fiber/particle/aluminum composites(MMCs). The tensile strength and elastic modulus of the hybrid MMCs are even 20% higher than those of the fiber reinforced MMCs with same volume fraction of reinforcements. This phenomenon is explained by the cluster model which is newly proposed in this research, and the strengthening mechanisms by a cluster is analyzed using simple modified rule of mixtures. From the analysis, it is observed that cluster structure in hybrid MMCs increase the fiber efficiency factor for the tensile strength and the orientation factor for the elastic modulus. The present theory is then compared with experimental results which was performed using squeeze infiltrated hybrid MMCs made of hybrid $Al_2O_3$ short fiber/particle preform and AC8A alloy as base metal, and the agreement is found to be satisfactory.