• Journal of the Korea Convergence Society
• /
• v.11 no.10
• /
• pp.225-229
• /
• 2020

In this study, the deformation and stress on each model was analyzed and the strength was compared with each other when the impacts on a total of four smart phone models was given. Models B and D with cases can be seen to have less deformation and stress than models A and C without cases. The models including the case have higher masses than the models without the case. So, the deformation and stress can be reduced by absorbing the impact force. In addition, the masses of models C and D are smaller than models A and B, but the stresses and deformations are seen to be smaller. If a case specialized for edge protection is chosen and designed when manufacturing a smart-phone in order to absorb the shock while weighing less, it is thought to improve the strength of the smart-phone and increase the durability. And it is seen that this study is adequate at the efficient design with durability of smart phone case practically and the aesthetic convergence of smart phone.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.8
• /
• pp.1129-1136
• /
• 2010

Damper springs in a drive-line absorb the impulsive torque generated when a lock-up clutch is connected directly, instead of via a fluid coupling. Design optimization and finite element analysis were performed to improve the shock- and vibration-absorption capacity of the lock-up clutch. For this purpose, a multi-body dynamics model was developed by including the main parts of a vehicle, such as an engine with a clutch, a transmission, drive shafts and wheels, and a whole mass of a vehicle. The spring constants were selected so that resonance of a system could be avoided. Damper springs were optimized on the basis of the spring constants, impulsive torques, compressed angles, spring counts, fatigue constraints, etc. Topology optimization was performed for three plates with the damper springs. The compliance was set up as an objective function, and volume fraction was fixed below 0.3. A new shape for the plates was proposed on the basis of the topology result.

• Journal of Labour Economics
• /
• v.25 no.2
• /
• pp.33-78
• /
• 2002

This study analyzes effects of the proposed reduction of legal working hours in Korea in which base wage is unchanged with working hours reduction. The theoretical analysis shows that a reduction of legal working hours would result in less than equal size reduction of actual working hours, and increase in wages. On the other hand, the effects on employment is ambiguous depending on the substitution effect and scale effect. An empirical analysis based on macro-economic model simulation supports the theoretical conjecture. It has been found that with the reduction of legal working hours, real wages and consumption increase while actual working hours decreases about half of the legal hours reduction. In addition, the immediate and outright imposition of legal hours reduction on all sectors of the economy is found to create a cost push inflation and reduce GDP, investment, and employment. This negative effects are lessened as the reduction of legal hours is gradually made and/or some measures to absorb the cost shock such as abolition of paid monthly leave are employed together.

• Proceedings of the KOSOMBE Conference
• /
• v.1997 no.11
• /
• pp.337-342
• /
• 1997

Dental implant has been increasingly used to recover the masticatory unction of tooth. It has been well known that the success of dental implant is heavily dependent on initial stability and long-term osseointegration due to optimal stress distribution in the surrounding bones. The role of periodontal ligament, removed during operation, is to absorb impact force and to distribute them to alveolar bone. or this reason, the study for artificial periodontal ligament has become an important issue in this field. In this study, chitosan was coated on dental implant or the purpose of replacing the role of intact periodontal ligament. The results by experiment and FEM analysis showed : I) Initial stability of dental implant was significantly increased(35%) when the implant was coated with chitosan. II) The coated implant showed higher impact absorption, more even stress distribution and lower stress magnitude under impact force than uncoated implant. Accordingly, the micro-fracture of the surrounding bones due to impact force would be lessened by chitosan coating on dental implant.

• Korean Journal of Applied Biomechanics
• /
• v.22 no.1
• /
• pp.113-121
• /
• 2012

The purpose of this study was to evaluate the effects of forefoot rocker shoes equipped with a metatarsal bar on lower extremity muscle activity and plantar pressure distribution. Ten healthy women in the age of twenties were participated in this study as the subjects. All subjects walked on a treadmill(Gait Trainer, BIODEX, USA) wearing normal shoes and metatarsal bar shoes, during which the plantar pressure distribution and muscle activity were measured. Using Pedar-X system(Novel Gmbh, Germany), the plantar pressure was measured for six regions of the foot: forefoot, midfoot, rearfoot, 1st metatarsal, 2-3th metatarsal, and 4-5th metatarsal, and for each sub-region, 4 features such as maximum force, contact area, peak pressure, and mean pressure were analyzed based on the plantar pressure. EMG(Electromyography) activity was measured by attaching surface electrodes to the rectus femoris, biceps femoris, tibialis anterior, and gastrocnemius medial head, and magnitude of muscle contraction was analyzed in IEMG(Integrated EMG) value. The results show that the maximum force, contact area, peak pressure, and mean pressure in the midfoot all increased while maximum force, peak pressure, contact area, mean pressure in the 1st metatarsal and 2-3th metatarsal all decreased when wearing functional shoes. Also, muscle activities in the four muscles were all decreased when wearing the functional shoes. This paper suggests that forfoot rocker shoes equipped with a metatarsal bar can help disperse the high pressure and absorb the shock to the foot as well as give positive influence on gait pattern and postural stability by reducing muscle fatigue during walking.

• Composites Research
• /
• v.32 no.5
• /
• pp.290-295
• /
• 2019

In the present study, composite insulation mat was reinforced over polyurethane foam (PUF) to improve the thermal performance and impact resistance of the PUF applied to the liquefied natural gas carrier insulation system. The composite insulation mat used Kevlar, aerogel, and cryogel composite mat that can be applied in a cryogenic environment. The thermal conductivity was measured at $20^{\circ}C$ to investigate the thermal performance, and the drop impact test was carried out under impact energy of 30 J at $20^{\circ}C$, $-163^{\circ}C$ to investigate the impact resistance. The measured thermal performance was compared with neat PUF through effective thermal conductivity theoretical value. The shock resistance was evaluated of contact force, contact time, and absorb energy. In experimental results, cryogel composite mat was the best performance in terms of thermal performance, and aerogel composite mat was the best performance in terms of impact resistance.

• International journal of advanced smart convergence
• /
• v.12 no.2
• /
• pp.76-83
• /
• 2023

Squatting of agricultural work can cause musculoskeletal disorders due to excessive pressure and rotational force on the knee joint In order to improve the assistive chair used in squatting agricultural work so that it can be used in a narrow groove, it is intended to improve the musculoskeletal harm of squatting work by attaching a spring on the assistive chair. Therefore, in the presenty study, 3D drawing was done using ProEngineer (3D), and a mock-up was produced and tested. Using pro-Engineer, it was judged that it was rare for plastic to be broken by a spring, so the analysis was conducted with a focus on springs. It was found that the structure that can absorb the shock according to the rigidity of the tape spring and balance the body is that the power to withstand the load of the weight is distributed as a whole when five springs are used. Electromyography was measured using ME600 (Mega Electronics, Finland) Measuring equipment attached to the waist, thighs, calves, and shins. EMG values were measured and compared with the prototype in two ways, when the worker did not wear the product and when he wore an existing product on the market. As a result of the experiment when using the prototype, the maximum EMG value for each part is considered to be helpful in preventing musculoskeletal diseases as the amount of muscle used is reduced in the waist, thighs, calves, and shins.

• Journal of the Korean Society of Radiology
• /
• v.17 no.6
• /
• pp.827-833
• /
• 2023

CT(Computed Tomography) contrast agents are commonly used in general hospitals and university hospitals when taking radiographic examinations. The CT contrast medium contains a mixture of a substance called "Iodine", which absorbs radiation energy and makes it appear white in the CT image, further improving the image quality. In addition, the CT contrast agent, which moves like blood in the blood vessels, clearly differentiates it from muscle and water, so CT contrast agents are widely used in hospitals. These CT contrast agents absorb X-rays, but in order to absorb X-rays, they must have a high density or a high radiation absorption coefficient. Since the CT contrast agent is injected into the blood vessels, if the density is high, the blood vessels are strained and the patient is in shock. For this reason, it is necessary to match the density similar to that of water and always pay attention to side effects. In addition, the amount of CT contrast medium is adjusted according to the patient's body shape, and the remaining contrast medium is discarded. However, This study tried to find out the idea of recycling it as a radiation shielding material. Since the CT contrast medium has a high radiation absorption coefficient at a density similar to that of water, the amount to absorb radiation is adjusted, the amount of contrast medium and the amount of water are adjusted, and the amount of radiation absorbed is determined by mixing with water. In addition, a study was conducted to find out the result of the difference in radiation absorption in various ways by comparing the radiation quality coefficient and absorption coefficient with other substances or materials in an environmentally friendly method harmless to the human body by mixing CT contrast medium and water.

• Journal of Conservation Science
• /
• v.30 no.2
• /
• pp.111-122
• /
• 2014

In Bongseon-ri site, the central type and the local type of the Baekje tombs co-exist together. Many swords with ring pommel which to regional leaders in Seocheon the Beekje government granted are excavated from these tombs. These represent that the regional leaders were controlled by the Baekje government gradually. Four swords with ring pommel and one simple sword are investigated metallurgically and we seek what swords have a function of weapon or what sword produce for grave goods. The simple sword is made by solid carburizing technology and quenching of heat treatment so it's possibly used as a weapon. In contrast, four swords with ring pommel has little chance of weapon because the blade of swords consists of microstructure that have low hardness and the back of swords don't have microstructure can absorb the shock. The most identical characteristic of the simple sword and swords with ring pommel is that they are possible to classify clearly into practical/non-practical tools. Additionally, according to non-metallic inclusion analysis result of these swords, w$\ddot{u}$stite and glass phase are found together. Thus, it is able to say that reduction method in low temperature is applied during smelting process.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.12
• /
• pp.106-111
• /
• 2017

In this study, the stiffness of an LMU (Leg Mating Unit), which is a device required for installing the top side part of an offshore structure, was examined through structural analysis. This unit is mounted on the supporting point of the structure and is used to absorb the shock at installation. It is a cylindrical structure with an empty center. To support the vertical load, elastomeric bearings (EBs) and iron plates are laminated in layers. The stiffness of the EBs is basically influenced by the size of the bearings, but it varies with the number of laminated sheets inside the same sized structure. The relationship between the stiffener and the compressive stiffness is investigated, and its design is suggested. The stiffness of the EBs is analyzed by calculating the reaction force, while controlling the displacement. First, the relationship between the size of the reinforcing plate and the compressive stiffness is considered. Next, the relationship between the number of stacked reinforcing plates and the compression stiffness is considered. Different loads are required for each installed point. The goal is to design the compression stiffness in such a way that the same deformation occurs at each point in the analysis. In this study, ANSYS is used to perform the FE analysis.