• 한국지진공학회논문집
• /
• 제7권6호
• /
• pp.93-99
• /
• 2003

구조물은 지진, 풍랑 등과 같은 외부의 충격에 대해서 노출되어 있기 때문에 대규모의 피해가능성이 항상 존재한다. 이러한 외부에 대한 충격흡수 장치는 여러 가지가 있다. 이러한 기구 중에서 널리 사용되고 있는 것이 기계적 에너지를 소산시키는 유압 감쇠기이다 본 논문에서는 유압 감쇠기의 단점을 보완하고 보다 효율이 높은 감쇠기를 나노기술을 응용하여 새로운 감쇠기에 대한 기초적 이론연구를 하였다. 새로운 감쇠기는 내부에 점성 유체 대신에 무기재료의 입자를 유체와 혼합하여 사용하였고 오리피스를 생략함으로 해서 보다 간단한 구조로 설계하였다. 나노 단위 기공에서의 유동 현상을 설명하기 위해서는 기존의 유체역학에 대한 지배방정식 및 가설들이 더 이상 적용이 되지 않는 단점이 있다. 본 연구에서는 지금까지 명확하게 규명되지 않았던 감쇠기의 열 발생, 나노 유동, 그리고 에너지 소산에 대한 이론적 해석을 수행하였다. 그리고 다공 입자 구조에 따른 에너지 소산에 대한 영향을 모델링하여 조사하였다. 감쇠 효과를 검토하기 위해 기존의 유압 감쇠기와 에너지 소산효율을 비교하였다. 또한 감쇠 효율을 수치적인 해석결과와 실험 결과를 서로 비교하여 검토하였다.

• 항공우주시스템공학회지
• /
• 제11권6호
• /
• pp.34-41
• /
• 2017

기존 알루미늄 하니콤 코어를 이용한 착륙선 충격완충장치의 대체 방안으로서 실리콘 고무와 같은 초점탄성 재료의 다중압출 특성을 이용한 새로운 개념의 충격 완충장치를 고찰하였다. 초점탄성재료가 오리피스 단면을 통과하며 압출되는 과정에서 재료 변형에너지 및 하중-변위 특성이 기존 하니콤 코어 특성과 유사하여 충격 완충 성능을 극대화 할 수 있는 측면에서 유사성을 가지고 있음을 알 수 있었다. 본 논문에서는 충격완충장치의 설계 구현가능성을 평가하고, 에너지 변환을 통한 충격흡수 매커니즘을 이해하기 위하여 유한요소해석 및 준정적 압축시험 결과를 검토하였다.

• Earthquakes and Structures
• /
• 제15권6호
• /
• pp.655-665
• /
• 2018

Shield tunnels are widely used throughout the world. However, their seismic performance has not been well studied. This paper focuses on the seismic response of a large scale model tunnel in compacted sand. A 9.3 m long, 3.7 m wide and 2.5 m high rigid box was filled with sand so as to simulate the sandy soil surrounding the tunnel. The setup was excited on a large-scale shake table. The model tunnel used was a 1:8 scaled model with a cross-sectional diameter of 900 mm. The effective shock absorbing layer (SAL) on the seismic response of the model tunnel was also investigated. The thickness of the tunnel lining is 60 mm. The earthquake motion recorded from the Kobe earthquake waves was used. The ground motions were scaled to have the same peak accelerations. A total of three peak accelerations were considered (i.e., 0.1 g, 0.2 g and 0.4 g). During the tests, the strain, acceleration and soil pressure on the surface of the tunnel were measured. In order to investigate the effect of shock absorbing layer on the dynamic response of the sand- tunnel system, two tunnel models were set up, one with and one without the shock absorbing layer of foam board were used. The results shows the longitudinal direction acceleration of the model tunnel with a shock absorbing layer were lower than those of model tunnel without the shock absorbing layer, Which indicates that the shock absorbing layer has a beneficial effect on the acceleration reduction. In addition, the shock absorbing layer has influence on the hoop strain and earth pressure of the model tunnel, this the effect of shock absorbing layer to the model tunnel will be discussed in the paper.

• 한국산업경영시스템학회:학술대회논문집
• /
• 한국산업경영시스템학회 2002년도 춘계학술대회
• /
• pp.291-296
• /
• 2002

The midsole hardness of athletic footwear affects capability of absorbing impact shock and controls rearfoot movement during running and walking. The prior studies were focused on examining the proper hardness of footwear for rearfoot movement or to finding effective hardness for absorbing impact shock. The displacements of maximal Achilles tendon angle described a amount of pronation motion is decreased when medial hardness of midsole is large more than lateral. Increasing hardness of footwear midsole are effected to reduce maximum and intial pronation angle, but declined the ability of impact shock during heelstrike. For determination of effectiveness hardness of midsole, therefore, the study that makes a compromise between rearfoot movement and absorbing impact during footstrike must be performed. The purpose of this study is to examine quantitative values of rearfoot control and absorbing impact shock with different hardness of medial and lateral midsole on heel portion. The results are useful to define biomechanical hardness of midsole for developing running shoes. As variable for impact shock, accelerations onto shank and knee are measured during 4 running speeds (5, 7, 9, 11km/h). Also, maximum and $10\%$ pronation angle (Achilles tendon angle) were measured using high-speed camera.

• 한국농공학회지
• /
• 제17권4호
• /
• pp.3962-3969
• /
• 1975

1. When the frame of the experimental apparatus was directly fixed on the platform, result from the spectrum density analysis showed that the generated vibration frequecy of the system was nearly-same as the system's own characteristic vibration frequency, 80Hz, in the case of the forcing vibration frequency was 7.5 to 22.5Hz. The reduction ratio of acceleration by balanced type model compare to non-balanced type one was 26.66 percent. 2. When the frame of experimental apparatus was fixed on the platform with putting a shock absorbing rubber between the frame and the platform, the generated vibration frequency of the system was same as forcing vibration frequency. When either frequency or the amplitude of the forcing vibration was increased, the acceleration ratio was increased too. The average reduction ratio was resulted 44.77 per cent. It was concluded that this method of acceleration measurement(the method using a shock absorbing rubber) was a reaonable method, because actual machine will work under such condition. As the vibration frequency and aptitude were increased, the absolute magnitude of acceleration was increased. 3. unbalanced rotating parts, and unbalanced moment of inertia of links were supposed to be causing factors of residual vibration in spite of using the balanced type oscillating mole drainer. This fact suggested that the attachment of the counter weight on the rotating parts which satisfy the condition mw$.$rw=m0e, was necessary. And also, it was expected that the shock absorbing effect could be improved by putting the shock absorbing materials between the moving parts and their supports.

• 한국소음진동공학회논문집
• /
• 제12권5호
• /
• pp.389-396
• /
• 2002

In this study, the dynamic absorbing system for gas operated gun has been investigated. For this purpose, firstly. mathematical model of gas-operated shoulder-fired gun has been constructed. Through a series of experimental works using the devised test setup, the characteristic behavior of mathematical model was compared to the test results. In order to design the dynamic absorbing system, parameter optimization process has been performed based on the simplified isolation system under constraints of moving displacement and transmitted force. In order to implement the more efficient dynamic absorbing system, the characteristic performance of stroke-dependent variable damping system has been analyzed with some opening area curves. Finally, the performance of the designed dynamic absorbing system has been evaluated by simulation and experiment using the previous test apparatus.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.293-295
• /
• 2004

In this research, we suggest the effective technique that the thickness of slab isn't increased, and considering proper shock absorbing material and supporting point, we make the floating floor which has multi-supporting system floating floor. As the result, it is effective in reduction of heavy weight system as well as one of light weight

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.928-931
• /
• 2003

In this research, we suggest the effective technique that the thickness of slab isn't increased, and considering proper shock absorbing material and supporting point, we make the floating floor which has multi-supporting system floating nut. As the result, it is effective in reduction of heavy weight system as well as one of light weight

• International Journal of Railway
• /
• 제4권4호
• /
• pp.103-108
• /
• 2011

The effect of the core cell shape on shock absorption characteristics of biomimetically inspired honeycomb structures has been numerically investigated. The finite element models of honeycomb test specimen composed of five core cells of identical mass have been constructed, and numerical simulations have been run on PAMCRASH. The dimensions of the sides of core cells as well as the angle between the sides have been shown to influence the shock absorption characteristics of the honeycomb structure. The specimen with regular hexagonal core cell shape is found to show the best shock absorbing capacity, and specimen with rectangle-like core cell are found to provide good shock absorbing characteristics.

• International Journal of Precision Engineering and Manufacturing
• /
• 제3권1호
• /
• pp.57-65
• /
• 2002

Pneumatic cylinder is widely used fur mechanical handling systems. Often, the impact occurs at the both ends points of pneumatic cylinder and generates the destructive shock with in the structural operating members of the machine or equipment. To reduce the damage of system, therefore, shock absorbing devices are required. Cushioning of pneumatic cylinders at one or both ends of piston stroke is used to reduce the shock and vibration. The cylinder body have to withstand under conditions of high velocity and load. In this research pneumatic cushioning cylinder moving tests have been conducted for different load mass and supply pressure. The velocity of pneumatic cylinder actuation system which is set vertically with multiple orifice cushion sleeve is controled with the meter-in/out control system. This study examines the dynamic characteristics of pneumatic cylinder which are used as cushion devices. It turns out that the cushion pressure is mainly a function of the external load rather than the supply pressure. The cushion region characteristics was also revealed in the meter-in control system.