• Journal of Ship and Ocean Technology
• /
• v.8 no.2
• /
• pp.1-12
• /
• 2004

To keep the ocean environment from pollutions, strict international requirements on the controllability are arisen to the VLCC. Especially in low speed operations near the harbor, the VLCC is often supported by tug to replenish the insufficient rudder force. When water jet is blown to the flapped rudder, the Coanda effect induces a high-lift force by delaying stall and re-enforcing circulation in a large angle of attack (Lachmann 1961, Ahn 2003). Based on numerous research efforts, the rudder system supported by the Coanda effect was devised and its performances were evaluated in the towing tank for a large VLCC model. Hydrodynamic forces acting on the rudder system were measured with a water jet blowing on the rudder surface and compared with those acting on a conventional rudder. The effectiveness of the new rudder system was proven through an experimental evaluation.

• Journal of the Society of Naval Architects of Korea
• /
• v.30 no.4
• /
• pp.46-60
• /
• 1993

Accurate measurements of fluctuating pressure in the cavitation tunnel are necessary to predict vibration and noise intensities in full scale ship. In this paper, the results of an experimental study on fluctuating pressure induced by a cavitating propeller are presented and discussed. Extensive measurements at several propeller revolutions are made using the flat plate to understand controversial problems of the effects of propeller revolution in the cavitation tunnel. The analysis of the uncertainties in experimental measurements and results is used to estimate the errors in uniform flow.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.50 no.1
• /
• pp.75-82
• /
• 2014

In vibration analysis of ships, the principle aim is to determine the natural frequencies and excitation frequencies, and use this information to avoid resonances and vibration damage. The simplest method is to prevent resonance conditions, which is effective as long as the natural frequencies and excitation frequencies can be regarded as independent from environmental conditions. For ships that use electric propulsion systems, the sources of vibration are reduced compared with those caused by a diesel engine or other combustion-based propulsion systems. However, the frequency spectrum of these vibrations may be different; therefore, to understand the characteristics of the electric propulsion, we also should investigate how the ship responds to these vibrations. We focused on a 1,000-ton deadweight (DWT) ocean-research vessel using an electric propulsion system and analyzed the response to vibration.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2006.11a
• /
• pp.201-204
• /
• 2006

A three-dimensional finite element (FEM) model has been developed to simulate the deformation due to bead on plate welding of curved plates with curvature in the weld direction. By using traditional method such as thermal-elastic-plastic FEM, the weld-induced deformation can be predicted accurately. However, this method is not practical approach to analyze the deformation of large and complex structures such as ship hull structures in view of time and cost. This study is classified from the aspect of equivalent load based on inherent strain near the weld line. Therefore, the residual deformation can be simply computed by elastic analysis. Further more, a practical solution is proposed to consider the contact between the plate and the positioning jig by judging the reaction forces of the jig at calculation step and the effect of the longitudinal curvature is closely considered.

• 한국전산유체공학회:학술대회논문집
• /
• 1996.05a
• /
• pp.93-98
• /
• 1996

Numerical computations are carried out to analyze characteristics of flow fields around an Wigley hull form which is advacing in the incoming waves. Navier-Stokes equations are solved by a finite difference method and a MAC method is used for coupling of pressure and velocity fields, and O-H grid topology is used.

• Journal of the Korean Institute of Navigation
• /
• v.20 no.3
• /
• pp.31-42
• /
• 1996

It is important to investigate the hull response of a fishing vessel in waves to ensure the safety of it and to keep excellent sea-keeping qualities. For this purpose, we measured the response of fishing vessels in waves using real sea experimental measuring system. We analyze the experimental data by statistical method and spectral analysis to get the characteristics of the response of vessels which have different tonnage. In this real sea experiment, we use three stern trawlers which are the training ship in university. We know that the distribution of experimental response have Gauss distribution and Rayleigh distribution and smaller vessels have larger response.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2000.10b
• /
• pp.51-58
• /
• 2000

The purpose of this study is the optimum modification of dynamic characteristics of stiffened plate structure. In the method of the optimization ,finite element method (FEM), sensitivity analysis and optimum structural modification method are used. To begin with, using FEM, the dynamic characteristics of stiffened plate structure is analyzed. Next, rate of change of dynamic characteristic by the change of design variable is calculated using the sensitivity analysis. Then, amount of change of design variable is calculated using this sensitivity value and optimum structural modification method. The change of natural frequency is made to be an objective function. Thickness of plate and cross section moment become a design variable. It is shown that the results are effective in the optimum modification for dynamic characteristics of the stiffened plate structure.

• Journal of Navigation and Port Research
• /
• v.42 no.5
• /
• pp.317-322
• /
• 2018

Marine weather information provided for vessels is mainly offered by radio devices such as NAVTEX, Weather Fax., and others. However, the information is too general for large areas, and lacks more detail. So, many seafarers are disinclined to use the information to initiate proper readiness of vessels' safety, avoiding marine accidents such as grounding, hull and cargo damage, but cannot develop an optimal and economical navigation plan, considering the inadequate level of low precision weather information. The purpose of this paper is to develop a strong wind warning system, based on the digital anemometer installed on the bridge. This study analyzed the data on 10-minutes average wind speed, when the vessel's grounding accidents happened in Korean ports. Results reveal that the vessel's strong wind warning algorithm, can estimate the growing of wind speed two-three hours in advance.

• Journal of Power System Engineering
• /
• v.8 no.4
• /
• pp.49-56
• /
• 2004

To design very large ships, such as very large drillships, we have to estimate the hydroelastic responses of the very large ships in waves. A numerical procedure is described for estimating the hydroelastic responses of very large ships advancing with slow speed in waves. The developed numerical approach is based on a combination of the three-dimensional source distribution method and the finite element method, including fluid-structure interaction by regarding a very large ship as many hull elements connected with elastic beam elements. Numerical results are compared with experimental and numerical ones obtained in the literature. The results of comparison confirmed the validity of the proposed approach.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.12
• /
• pp.1329-1337
• /
• 2009

Because the tonal sound of the underwater noise in a naval vessel can be identified from the sub-marine of the enemy, it should be reduced sufficiently. This kind of the noise usually comes from the structure-borne noise of the onboard machine and transfers to the sea through the hull of the ship. The vibration at the high frequency can be reduced sufficiently with damping material. In this paper, the damping coefficient of the steel plate with damping sheet is evaluated by experiment. Using these evaluated properties, the numerical analysis is performed in order to evaluate how much vibration of the generator can be reduced applying damping sheet on the encloser and base of it.