• Bulletin of the Society of Naval Architects of Korea
• /
• v.4 no.1
• /
• pp.49-54
• /
• 1967

The authors considered the effects of trim in the small coastal passenger boat upon resistance in this paper. Any change of trim no matter how small, necessarily produces some effect upon resistance. The relations between the resistance coefficients and trim were investigated through the towing test of the Model $MCI-P_1-65$, Korean Standardized Ship, GT 70 tons passenger boat in the gravitational tank. The Lines of the Model are given in Fig. 1. Principal dimensions and other characteristics vary with the trim in general. Those values varied with the trim for $MCI-P_1-65$ are tabulated in table 1. The resistance was measured at five conditions such as even keel, 0.0273L, (original designed trim) 0.0473L, 0.0663L, 0.0873L trim by the stern, fixing the displacement corresponding to the designed load water line. Model was made of wood in length of 3.5 feet coated with varnish, and without appendages. As the artificial turbulent stimulator, the sand strip method was used. The results of model towing tests, correcting to water temperature of $70^{\circ}F$, were expanded to full scale using the Schoenherr's friction formula and surface roughness allowance coefficient of 0.0004. The authors point out, the following results. 1) Optimum trim which gives the minimum resistance exists for every speed at constant displacement and each comes to the same value. For $MCI-P_1-65$ optimum trim is 0.0673L trim by the stern(Fig.4-The cross curves of the resistancecoefficients). 2) At constant displacement, when LCB(longitudinal position of center of buoyancy) varies with the trim, there exists optimum value of LCB which gives minimum resistance for every speed and each comes to the same value. For $MCI-P_1-65$ optimum position of LCB is 8%L aft from midship section (Fig.6).

• Journal of Ocean Engineering and Technology
• /
• v.20 no.6 s.73
• /
• pp.123-129
• /
• 2006

The mechanical properties of bellows, such as the extensibility and the strength can be changed depending on the shape. For the shipbuilding material, it is desirable that the fatigue life is long due to the elastic property and the reduction of thermal stress in piping system. Nowadays, the domestic production and design of bellows are based on the E.J.M.A. Code. Therefore, the design standard is in need because of much errors and lack of detailed analysis. In this study, it is attempted to find out the optimal shape of U-type bellows using the finite element analysis. The design factors, mountain height, length, thickness, and the number of convolutions are considered and the proper values are chosen for the simulation. The results shaw that as the number of convolutions reduces, the volume decreases while the stress increases. However, as the number of convolutions increases, the volume increases above the standard volume and the stress obviously increases. In addition, the effect of the thickness of bellows on the stress is very large. Both of the mass and stress are decreasing at a certain lower value region. Also, we investigated shape optimization with considering maximum stress distribution tendency.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.6
• /
• pp.850-856
• /
• 2012

Bilateration using two fixed nodes has been used in the field of the real time indoor location system in the narrow space such as building or ship passage. However, as the distance between the fixed nodes increases or any obstructions exist in their zone, it is difficult to detect the location of mobile node(user) due to the degradation of its reception ratio. In order to compensate for these problems, this paper presents, based on IEEE 802.15.4a chirp signal, a new real time indoor location system using stride measurement algorithm which can calculate the location through sensors attached to user. The proposed system consists of an ultrasonic sensor to measure the leg length, a geomagnetic sensor to recognize the user's orientation, and an inertial sensor to obtain the angle between the legs. The experimental results are shown that the proposed system has twice or more accurate output compared with conventional indoor location method in the section which is partially out of communication reachability.

• Proceedings of KOSOMES biannual meeting
• /
• 2007.05a
• /
• pp.109-113
• /
• 2007

Yacht have an high powered main engine relatively light hull, so the noise generated from the engine have a bad influence upon the crew and passenger. Recently, cruise yacht is made an attempt by domestic production skill, however the insulation skill of the noise made by the main engine is not satisfy the real purchasing power of the buyer. Like this, yacht cabin's noise level is becoming the barometer to decide the purchase. the method to insufficient. However, if we use the skill of the monitoring equipment and the genetic algorithm system, the circumference of the main engine can be enclosed by an high quality absorbtion wall and the noise levels of the cabins are improved. In this study, the sound absorbtion barrier is experimentally researched by change the volume and the length of the neck for the Helmholtz resonator as the resonator can absorb the noise effectively.

• Metals and materials international
• /
• v.24 no.6
• /
• pp.1193-1201
• /
• 2018

Dilatometry is a useful technique to obtain experimental data concerning transformation. In this paper, a dilation conversional model was established to calculate carbides fraction in AISI H13 hot-work tool steel based on the measured length changes. After carbides precipitation, the alloy contents in the matrix changed. In the usual models, the content of carbon atoms after precipitation is considered as the only element that affects the lattice constant and the content of the alloy elements such as Cr, Mo, Mn, V are often ignored. In the model introduced in this paper, the alloying elements (Cr, Mo, Mn, V) changes caused by carbides precipitation are incorporated. The carbides were identified using scanning electron microscope and transmission electron microscope. The relationship between lattice constant of carbides and temperature are measured by high-temperature X-ray diffraction. The results indicate that the carbides observed in all specimens cooled at different rates are V-rich MC and Cr-rich $M_{23}C_6$, and most of them are V-rich MC, only very few are Cr-rich $M_{23}C_6$. The model including the effects of substitutional alloying elements shows a good improvement on carbides fraction predictions. In addition, lower cooling rate advances the carbides precipitation for AISI H13 specimens. The results between experiments and mathematical model agree well.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.26 no.6
• /
• pp.634-643
• /
• 2020

Because of the continuous increase in the demand for and importance of marine space, marine exploration and survey activities are being actively conducted in Korea actively. Because the marine survey vessels used for these activities have special operational patterns depending on the purpose and probe vessels, research on maritime traffic risk is required. In this study, an attempt was made to determine the correlation of each factor with the effect of marine exploration and survey vessel operation on maritime traffic. The status of ocean exploration and survey vessels in operation in Korea was identified, as well as the special operational conditions of some of the ocean physical probes. Generally, the number of exploration and survey vessels involved per hour, total vessel length(including exploration equipment), operation, interval distance of exploration as per plan, and marine traffic conditions(traffic volume and speed) can be classified as operating factors. To compare the results of the environmental stress, a maritime traffic flow simulation based on the "ES" Model was performed with each of the identified operating factors as independent variables. The results of the analysis confirmed that the environmental stress significantly changed in the order of traffic volume, ship length and speed. In addition, it was confirmed that the environmental stress is reduced when the operation course is set at an angle with the nearby maritime traffic flow. Accordingly, it can help reduce the operator's burden if the survey vessel operator understands nearby maritime traffic conditions and reflects them in the operation method when setting the operation plan.

• Korean Journal of Food Science and Technology
• /
• v.17 no.6
• /
• pp.415-420
• /
• 1985

In this study, changes in physical and chemical properties of glutinous rice during various soaking periods (0, 0.08, 1, 3, 5, 7, 10 days) were investigated in order to clarify the relations ship between soaking period and expansion volume in the preparation of Gang Jung. The longer the soaking period was, the greater the expansion volume of Gang Jung was. Higher maximum viscosity and breakdown in amylogram of glutinous rice flour were observed as the soaking period was increased, As the length of soaking period increased, hardness of glutinous rice and size of flour particle significantly decreased, while sweeling power and solubility of glutinous rice flour showed no significant difference. Increased length of soaking period was associated with higher fatty acidity, higher acidity of water extract and lower pH of glutinous rice flour. Control of flour particle size distribution resulted in significantly larger expansion volume of Gang Jung. Brabender's amylogram showed that the increase of expansion volume of Gang Jung associated with the increase of soaking period was related to the change of rheological properties of glutinous rice. It seemed that changes in viscometric properties of glutinous rice was attributed to the different flour particle size distribution resulted from changes in hardness of rice during soaking.

• Journal of the Korean Institute of Navigation
• /
• v.23 no.1
• /
• pp.75-84
• /
• 1999

Although many studies on modelling of port competitive situation have been conducted, both theoretical frame and methodology are still very weak. In this study, therefore, a new algorithm called ESD (Extensional System Dynamics) for the evaluation of port competition was presented, and applied to simulate port systems in northeast asia. The detailed objectives of this paper are to develop Unit fort Model by using SD(System Dynamics) method; to develop Competitive Port Model by ESD method; to perform sensitivity analysis by altering parameters, and to propose port development strategies. For these the algorithm for the evaluation of part's competition was developed in two steps. Firstly, SD method was adopted to develop the Unit Port models, and secondly HFP(Hierarchical Fuzzy Process) method was introduced to expand previous SD method. The proposed models were then developed and applied to the five ports - Pusan, Kobe, Yokohama, Kaoshiung, Keelung - with real data on each ports, and several findings were derived. Firstly, the extraction of factors for Unit Port was accomplished by consultation of experts such as research worker, professor, research fellows related to harbor, and expert group, and finally, five factor groups - location, facility, service, cargo volumes, and port charge - were obtained. Secondly, system's structure consisting of feedback loop was found easily by location of representative and detailed factors on keyword network of STGB map. Using these keyword network, feedback loop was found. Thirdly, for the target year of 2003, the simulation for Pusan port revealed that liner's number would be increased from 829 ships to 1,450 ships and container cargo volumes increased from 4.56 million TEU to 7.74 million TEU. It also revealed that because of increased liners and container cargo volumes, length of berth should be expanded from 2,162m to 4,729m. This berth expansion was resulted in the decrease of congested ship's number from 97 to 11. It was also found that port's charge had a fluctuation. Results of simulation for Kobe, Yokohama, Kaoshiung, Keelung in northeast asia were also acquired. Finally, the inter port competition models developed by ESB method were used to simulate container cargo volumes for Pusan port. The results revealed that under competitive situation container cargo volume was smaller than non-competitive situation, which means Pusan port is lack of competitive power to other ports. Developed models in this study were then applied to estimate change of container cargo volumes in competitive relation by altering several parameters. And, the results were found to be very helpful for port mangers who are in charge of planning of port development.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.11
• /
• pp.740-745
• /
• 2016

Cables are installed for tens of thousands of connections between various pieces of equipment to operate and control a commercial ship. The correct shortest-route data is necessary since these are complicated cable installations. Therefore, an overfill interval commonly exists in the shortest paths for cables as estimated by Dijkstra's algorithm, even if this algorithm is generally used. It is difficult for an electrical engineer to find the overfill interval in 3D cable models because the occupancy rate data exist in a data sheet unlinked to three-dimensional (3D) computer-aided design (CAD). The purpose of this study is to suggest a visualization method that displays the cable path and overfill interval in 3D CAD. This method also provides various color visualizations for different overfill ranges to easily determine the overfill interval. This method can reduce cable-installation man-hours from 7,000 to 5,600 thanks to a decreased re-installation rate, because the cable length calculation's accuracy is raised through fast and accurate reviews based on 3D cable visualization. As a result, material costs can also be reduced.

• Journal of Navigation and Port Research
• /
• v.42 no.3
• /
• pp.201-206
• /
• 2018

The purpose of this study is to estimate a proper Domain Watch between anchored vessels in order to propose a method for the efficient management of VTS(Vessel Traffic Service) of the N-anchorage in Busan harbor, which is the largest port in Korea. For this purpose, we proposed the calculation method of Domain Watch and investigated the ship length(L), the distance between anchored vessels ($D_{ij}$), the domain radius(R), and the domain radius vs L(R/L) during the peak time of the vessels in the latest usage of anchorage. As a result of technical analysis for the surveyed data, the minimum R/L for securing the safety distance between anchored vessels was selected based on 2.85 corresponding to the 70th percentile of the total data. This result was applied to the N-anchorage of Busan and compared with the 'Guidelines of Port and Harbor Design(2014)', and we have confirmed that it is reasonable to set the Domain radius with the minimum 2.85L or more in VTS. This study considers the safety management of anchorage for VTS. This study could contribute to the safety of vessels using anchorage and the safety management plan of VTS when it is applied to other ports in operation such as it was in Busan.