• Nuclear Engineering and Technology
• /
• 제31권6호
• /
• pp.541-547
• /
• 1999

Corrosion control, in the end-shield cooling system of Wolsung Nuclear Power Plant, is directly related to the control of dissolved oxygen (DO). The current method, being used to deoxygenate the end-shield cooling water, is a chemical treatment by addition of reducing agent, hydrazine, to react with DO. This method has several limitations including high reaction temperature of hydrazine , unwanted explosive hydrogen gas production, and its intrinsic harmful property. A new approach to remove DO using a membrane-based oxygen removal system (MORS) was tried to overcome limitations of the hydrazine treatment. The DO removal efficiency of the MORS was found to be in the range 87% to 98%: The higher vacuum, the lower water flow rate and the higher water temperature tend to increase the DO removal efficiency.

• 대한기계학회논문집
• /
• 제18권7호
• /
• pp.1833-1839
• /
• 1994

Experiments have been carried out to investigate the burning characteristics of waste tires in high temperature environments. The burning of waste tire chips consists of four stages ; evaporation of volatile matters, ignition, burning of volatile matters, and burning of solid carbon. Burning time of waste tire chips depends on the gas temperature and the initial weight of the chip. However, the environments. In the ceramic matrix burner with a ceramic radiation shield, the burning time of the waste tire chips becomes shorter than that without the shield. This is due to the increase in heat transfer to the tire chips by radiation.

• Journal of Korean Vacuum Science & Technology
• /
• 제7권2호
• /
• pp.27-32
• /
• 2003

A large cryo-pumping system composed of 4 cryosorption pumps was designed and manufactured to satisfy the pressure requirements of the NBI test stand. The cryosorption pump consists of a thermal shield/baffle assembly and a cryopanel coated with activated carbon granules. The thermal shield is cooled by liquid nitrogen, and the cryopanel by a commercial helium refrigerator. The operation characteristics and vacuum performance of the cryosorption pump were investigated. The cooling down time of the cryopanel to 20 K was about 6 hours with a liquid nitrogen consumption rate of about 35 L/hr. The maximum pumping speed of the cryosorption pump for the hydrogen gas measured by the steady pressure method was about 90,000 L/s.

• Journal of Welding and Joining
• /
• 제20권1호
• /
• pp.26-33
• /
• 2002

This study was undertaken to obtain the fundamental knowledges on the weld deflects and it's realtime monitoring method. The paper describes the results of high speed photography, acoustic emission (AE) detection and plasma light emission (LE) measurements during $CO_2$ laser welding of STS 304 stainless steel and A5083 aluminum alloy in different welding condition. The characteristic frequencies of plasma and keyhole fluctuations at different welding speed and shield gases were measured and compared with the results of Fourier analyses of temporal AE and LE spectra, and they had considerably good agreement with keyhole and plasma fluctuation. Namely, the low frequency peaks of AE and LE shifted to higher frequency range with the welding speed increase, and leer the argon shield gas it was higher than that in helium and nitrogen gases. The low frequencies dominating in fluctuation spectra of LE probably reflect keyhole opening instability. It is possible to monitor the weld bead deflects by analyzing the acoustic and/or plasma light emission signals.

• Journal of Welding and Joining
• /
• 제24권1호
• /
• pp.56-63
• /
• 2006

The characteristics of $CO_2$ or Nd:YAG laser welded 600MPa ade TRIP steel was investigated. He or Ar gas was used as a shield gas in case of $CO_2$ laser welding, but the shield gas was not used in case of Nd:YAG laser welding. Bead on plate welding was performed with various welding conditions. Defects in the joints of both welding type occurred at 1.8m/min but were not observed over the welding speed of 2.1m/min in case of Nd:YAG laser welding. However, porosity occurred in $CO_2$ laser welding and the tendency of decreasing with the increase of welding speed. The hardness was the highest at heat affected zone near fusion zone as well as at the fusion zone and decreased on approaching the base metal. In a perpendicular tensile test to the weld line, all specimens that have been welded at optimum conditions were fractured at the base metal, and the tensile properties showed the rather higher than those of raw material. In a parallel tensile test, the strength of the joints was higher than that of the base metal. Elongation was found to be lower than that of the raw material. Forming height by Erichsen test and elongation were deeply related with the ratio of base metal/weld metal and the maximum hardness of the weld metal. Also porosity induced to decrease the strength and the elongation. The maximum formability was recorded at approximately 80% as compared with that of the raw material with the optimum condition.

• Journal of Welding and Joining
• /
• 제31권1호
• /
• pp.38-42
• /
• 2013

보호가스의 성분구성은 특별한 적용대상이나 목표로 하는 용접결과를 위해 선택해야 한다. 모재의 종류, 두께, 요구되는 비드 모양, 용접속도, 그리고 요구되는 용접품질 등 이 모든 것이 혼합가스 성분 구성의 선택에 영향을 미친다. 적절한 가스 공급 장치와 적절한 가스 유량으로 공급되는 최적 품질의 보호가스는 용접품질이 뛰어나며 용접결함을 발생시키지 않게 된다.

• 한국가스학회지
• /
• 제23권4호
• /
• pp.28-39
• /
• 2019

OGI(Optical Gas Image) 기술에서 주요 가스의 이미지 특성연구는 누출가스의 종류 파악 및 배출량 추정의 기초자료가 될 수 있다. 본 연구의 목적은 산업에서 중요한 methane과 propane 두 탄화수소의 분출가스 이미지의 차이를 관찰하기 위함이다. 적외선을 투과하는 성질을 지닌 석영을 끼운 바람차단막을 제작하여 methane과 propane을 동시에 누출하게 하여 적외선 OGI 카메라로 촬영하고, 그 영상을 분석하였다. 석영차단막이를 활용하여 바람의 영향을 최소화하여 안정된 영상을 확보하였다. 누출 기준값을 1 L/min로 하여 두 탄화수소의 영상을 분석한 결과 OGI 카메라로 쉽게 식별 가능한 거리가 methane의 경우 6 m, propane의 경우 9 m로 나타났다. 적외선 카메라와 누출지점의 거리 1~10 m까지에서 propane의 경우가 methane의 경우 보다 gas plume의 크기가 컸으며 선명하였다. 영상 이미지의 점의 수로 비교하면 propane이 methane보다 평균 3.8배 많았다.

• 한국산업안전학회:학술대회논문집
• /
• 한국안전학회 2002년도 추계 학술논문발표회 논문집
• /
• pp.257-262
• /
• 2002

The object of this study is to investigate the effect of compounded welding through the AE (Acoustic Emission) characteristics for weld HAZ (Heat Affected Zone) on static tensile test. This study was carried out a SM 490A, high tension steel using the low hydrogen type E4316 of electronic shield metal arc welding, compound wire of $CO_2$ gas arc welding and tungsten electrode of TIG welding.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 춘계 학술발표대회 개요집
• /
• pp.60-62
• /
• 2004

TIG 용접에서 용입과 비드가 형성되어 가는 물리적 아크 현상을 이해함에 있어서 아크 압력은 매우 중요한 인자 중의 하나이다$^{1.2)}$ . 기존의 연구에서는 저전류나 중전류 영역의 TIG 용접에서 텅스텐 전극의 선단각과 용입 형태와의 관계를 플라즈마 기류 등에 고찰하였고, 최대 아크압력에 미치는 전극형상의 영향 등을 연구하였다. (중략)

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.657-658
• /
• 2005

Flame retard of polymers was studied for prevention from burning by various additives stimulated the char formation during heating and thermal degradation of polymer materials. Forming char have high porosity, low thermal conductivity and act as thermal shield for heat transmission from the flame to the polymer and. oxygen towards the polymer. The results showed that various additives may regulate the processes of intumecsence. The efficient fire protective intumescent char was result of processes of melting, gas evolution, cross-linking, carbonization etc.