• The Journal of the Petrological Society of Korea
• /
• v.16 no.2 s.48
• /
• pp.47-58
• /
• 2007

This study examines the distribution of basement rocks in Gyochon-ri, Muan-eup, Muan-gun, Jeonnam where ground subsidence occurred in June 2005, and traces corrosion of limestone. Mica schist and rhyolite are distributed in the surface of the study area, but thick limestone layer with large and small caverns are distributed underground. A horizon of limestone with maximum width of 300 m and 4 km of length was found along the detour which is in the north of pound subsidence. Such identification of limestone presence would be very useful to predict potential ground subsidence. Limestone in this area was disturbed by fold and fault due to severe shearing deformation. Small caverns were frequently found in anticline part of folds formed in limestone layer. Schists with different thicknesses were intercalated in the limestone with shearing deformation and consist of sheet silicate minerals (chlorite and mica) and quartz. In sections of weathered specimen, it is shown that biotite of schist part was altered into chlorite and corrosion of calcite around the schist followed. This suggest that ground water permeated between intercalated sheet silicate minerals and corrosion of limestone began. And small caverns were generated where active corrosion occurred. This study suggests that because of many reasons (for instance, reclamation of the Bulmu reservior and excess pumping), cavern water level was lowered and cave sediments were removed, and it caused ground subsidence to occur.

• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.1
• /
• pp.35-40
• /
• 2018

Nd:YAG laser was used to carbonize polyimide films to produce carbon films. This is a simple manufacturing process to fabricate low cost sensors. By applying this method, we studied characteristics of flexible and low-cost piezoresistive. Previously, many studies focused on carbonization of polyimide using $CO_2$ laser with wavelength of $10.6{\mu}m$. In this paper, carbonization (carbonization process) was performed on polyimide films using an Nd:YAG laser with a wavelength of $1.064{\mu}m$. In order to increase the resolution, we optimized the laser conditions of the power density ($W/cm^2$) and the beam scan rate. In previous studies using $CO_2$ laser, the minimum line width was $140{\sim}220{\mu}m$ but in this study, carbon line width was reduced to $35{\sim}40{\mu}m$. The initial sheet resistance of the carbon sensor was $100{\sim}300{\Omega}/{\square}$. The resistance decreased by 30% under stretched with a curvature radius of 21 R. The calculated gauge factor was 56.6. This work offers a simple, highly flexible, and low-cost process to fabricate piezoresistive sensors.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.2
• /
• pp.144-150
• /
• 2002

Indian mallow is characterized by the rapid growth and high harvest of the fibrous materials. This study was carried out to investigate the sheet properties of Hanji using Indian mallow, made by different pulping methods, such as alkali and sulfomethylated pulpings and different stock compositions, various mixing ratios of bast fiber, woody core and whole stalk fibers. The results from this study were summarized as follows. The length and width of the bast fibers were 1.40-430 mm(av. 235 mm), and 9.2-26.4 ㎛(av.18.3 ㎛), respectively. The cell wall thickness was 4.0-115 ㎛(av. 7.7 ㎛). Runkel ratio, flexibility coefficient and fiber length/fiber width ratio were 1.38, 0.42 and 128 respectively. Bast fiber and whole stalk were cooked by alkali and sulfomethylated methods. Sulfomethylated pulping resulted in superior pulp in terms of yield and quality as compared with those of alkali pulping. The pulp yields of bast fiber was higher than those of whole stalk

• Journal of Korean Society of Forest Science
• /
• v.31 no.1
• /
• pp.37-42
• /
• 1976

In this study, an effort was made to find out more effective methods for vegetation establishment on denuded forest land along Cheon Bo Mountains, This area has serious sheet erosion as a major erosion process and parent material is granite gneiss which is known as one of the most erosive materials. Lespedeza bicolor, Arundinella hirta and Robinia pseudoacacia were used as ground cover species. Seeding methods were open broadcast seeding and broadcast seeding with straw mulch, dill seeding with 10cm and 20cm width, and spot seeding with 20cm and 30cm diameter. 1. On slopes less than 30 degrees, broadcast seeding method with straw mulch was the most effective way to establish vegetation cover. 2. On steep slopes more than 30 degrees, 10cm drill seeding method was more effective than the other methods. 3. Soil Texture has an influence on vegetation establishment governing soil moisture condition. Coverage and fresh weight were increased with the fine material qantity in soil. 4. In process of year, coverage was increased with fresh weight. On the other hand, survival decreased.

• Steel and Composite Structures
• /
• v.23 no.5
• /
• pp.571-583
• /
• 2017

A kind of accordion-web RBS connection, "Tubular Web RBS (TW-RBS)" connection is proposed in this research. TW-RBS is made by replacing a part of web with a tube at the desirable location of the beam plastic hinge. This paper presents first a numerical study under cyclic load using ABAQUS finite element software. A test specimen is used for calibration and comparison of numerical results. Obtained results indicated that TW-RBS would reduce contribution of the beam web to the whole moment strength and creates a ductile fuse far from components of the beam-to-column connection. Besides, TW-RBS connection can increase story drift capacity up to 9% in the case of shallow beams which is much more than those stipulated by the current seismic codes. Furthermore, the tubular web like corrugated sheet can improve both the out-of-plane stiffness of the beam longitudinal axis and the flange stability condition due to the smaller width to thickness ratio of the beam flange in the plastic hinge region. Thus, the tubular web in the plastic hinge region improves lateral-torsional buckling stability of the beam as just local buckling of the beam flange at the center of the reduced section was observed during the tests. Also change of direction of strain in arc shape of the tubular web section is smaller than the accordion webs with sharp corners therefore the tubular web provides a better condition in terms of low-cycle fatigue than other accordion web with sharp corners.

• Journal of Korean Society of Steel Construction
• /
• v.21 no.5
• /
• pp.545-552
• /
• 2009

An experimental study was performed on the yLRC composite column. Its external surface was manufactured with y-shape steel sheets and L-shape steel angles, and concrete was poured inside in the field. This composite column has improved the section capacity due to the composite action of steel and concrete, and provides good efficiency in reducing the terms of construction works because of its abridged formworks. The stub column specimens (three small and three large specimens) were tested through concentrical axial loading, and the effect of the width-to-thickness ratio of the steel angle on the column axial strength was examined. The axial strength and behavior of the composite columns were analyzed, and a formula for predicting the axial load capacity was proposed.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.116.1-116.1
• /
• 2011

Materials with a combination of high electrical conductivity and optical transparency are important components of many electronic and optoelectronic devices such as liquid crystal displays, solar cells, and light emitting diodes. In this study, to fabricate a low-resistance and high optical transparent electrode film for organic photovoltaic, the following steps were performed: the design and manufacture of an electroforming stamp mold, the fabrication of thermal roll imprinted (TRI) poly-carbonate (PC) patterned films, the manufacture of high-conductivity and low-resistance Ag paste which was filled into patterned PC film using a doctor blade process and then coated with a thin film layer of conductive polymer by a spin coating process. As a result of these imprinting processes the PC films obtained a line width of $10{\pm}0.5{\mu}m$, a channel length of $500{\pm}2{\mu}m$, and a pattern depth of $7.34{\pm}0.5{\mu}m$. After the Ag paste was used to fill part of the patterned film with conductive polymer coating, the following parameters were obtained: a sheet resistance of $9.65{\Omega}$/sq, optical transparency values were 83.69 % at a wavelength of 550 nm.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.215-216
• /
• 2013

The silicide is a compound of Si with an electropositive component. Silicides are commonly used in silicon-based microelectronics to reduce resistivity of gate and local interconnect metallization. The popular silicide candidates, CoSi2 and TiSi2, have some limitations. TiSi2 showed line width dependent sheet resistance and has difficulty in transformation of the C49 phase to the low resistive C54. CoSi2 consumes more Si than TiSi2. Nickel silicide is a promising material to substitute for those silicide materials providing several advantages; low resistivity, lower Si consumption and lower formation temperature. Nickel silicide (NiSi) nanowire (NW) has features of a geometrically tiny size in terms of diameter and significantly long directional length, with an excellent electrical conductivity. According to these advantages, NiSi NWs have been applied to various nanoscale applications, such as interconnects [1,2], field emitters [3], and functional microscopy tips [4]. Beside its tiny geometric feature, NW can provide a large surface area at a fixed volume. This makes the material viable for photovoltaic architecture, allowing it to be used to enhance the light-active region [5]. Additionally, a recent report has suggested that an effective antireflection coating-layer can be made with by NiSi NW arrays [6]. A unique growth mechanism of nickel silicide (NiSi) nanowires (NWs) was thermodynamically investigated. The reaction between Ni and Si primarily determines NiSi phases according to the deposition condition. Optimum growth conditions were found at $375^{\circ}C$ leading long and high-density NiSi NWs. The ignition of NiSi NWs is determined by the grain size due to the nucleation limited silicide reaction. A successive Ni diffusion through a silicide layer was traced from a NW grown sample. Otherwise Ni-rich or Si-rich phase induces a film type growth. This work demonstrates specific existence of NiSi NW growth [7].

• Journal of the Korean Society of Clothing and Textiles
• /
• v.2 no.1
• /
• pp.157-166
• /
• 1978

The purpose of this study was; (1) to examine ready-to-wear dresses to find the characteristics of labels and construction which existed at three different price levels and (2) to make the gathered information available to consumers, designers, manufacturers and the people who are concerned with ready-to-wear garments. A check sheet was made listing a wide variety of features which could cause garments to be different. For the statistical analysis. 87 dresses were used out of 116 dresses examined. Observation was made at the stores in Myung Dong, Suh-Dae Moon and No Ryang Jin in Seoul from February 16, 1978 to March 3, 1978. The findings are; 1. The average prices of high, medium and low priced levels were ${\\}54,728$, ${\\}41,448$ and ${\\}7,225$. The average price discrepancy between high and medium priced levels was ${\\}13,000$ and ${\\}34,194$ between medium and low priced levels. 2. Most of the dresses examined had labels in all three priced levels. The most informative labels were found on medium priced dresses and then high. The low priced dresses had no information which would be of help to the consumer in regard to care, size and Jiber content. 3. Most of the dresses examined were cut on lengthwise grain. The stitching of medium and high priced levels were satisfactory. The chief way of fastening threads at the end of stitching was by backtracking. $28\%$ of the low priced levels was found unappropriate in stitching number because it was too large to the fabric. Many dresses in low priced levels were not pressed well. The average hem width of low priced dresses were less than 3cm, the high 3-4cm and the medium 4-5cm. Hemming was done mostly by hand in high and medium and by machine in low priced dresses. The medium priced dresses used more linings than low and high priced dresses.

• Current Photovoltaic Research
• /
• v.2 no.4
• /
• pp.173-176
• /
• 2014

We have investigated the seed layer formation of front side contact using the inkjet printing process. Conductive silver ink was printed on textured Si wafers with 80 nm thick $SiN_x$ anti reflection coating (ARC) layers and thickened by light induced plating (LIP). The inkjet printable sliver inks were specifically formulated for inkjet printing on these substrates. Also, a novel method to prepare nano-sized glass frits by the sol-gel process with particle sizes around 5 nm is presented. Furthermore, dispersion stability of the formulated ink was measured using a Turbiscan. By implementing these glass frits, it was found that a continuous and uniform seed layer with a line width of $40{\mu}m$ could be formed by a inkjet printing process. We also investigated the contact resistance between the front contact and emitter using the transfer length model (TLM). On an emitter with the sheet resistance of $60{\Omega}/sq$, a specific contact resistance (${\rho}_c$) below $10m{\Omega}{\cdot}cm^2$ could be achieved at a peak firing temperature around $700^{\circ}C$. In addition, the correlation between the contact resistance and interface microstructures were studied using scanning electron microscopy (SEM). We found that the added glass particles act as a very effective fire through agent, and Ag crystallites are formed along the interface glass layer.