• 자원리싸이클링
• /
• 제15권6호
• /
• pp.48-55
• /
• 2006

가정용 폐건전지의 재활용 상용화를 위하여 물리적 처리방안에 대한 재활용 기술을 확립하기 위한 형상선별, 파쇄, 자력선별, 입도분리 그리고 와전류 정전선별을 통한 물리적 처리연구를 수행하였다. 그 결과 형상선별기를 이용하여 폐망간전지를 형상별 중량별로 시간당 $400{\sim}600$개의 속도로 분리하는 기술을 확립하였다. 파쇄, 자력선별 그리고 입도분리를 통해 망간, 아연, 철의 함량을 조사해본 결과, 자성체에는 망간과 아연 둥의 불순물 함량이 각각 0.1%이하였으며 99%이상이 Fe임을 알 수 있었다. 또한 비자성체의 경우에는 폐망간전지 종류에 따라 Zn이 $22{\sim}30%$, Mn이 $16{\sim}22%$ 그리고 Fe는 $1{\sim}3%$정도였고 기타 탄소봉과 플라스틱, 종이 등이 대략 $37{\sim}50%$정도였다. 와류 정전선별기로 Zn 판상을 회수한 결과, 최적실험 조건인 선속 $2,250m/min{\sim}2,750m/min$ 사이에서 96%이상의 회수가 이루어졌다.

• International Journal of Fluid Machinery and Systems
• /
• 제8권2호
• /
• pp.94-101
• /
• 2015

To investigate the influence of blade profiles on cavitation behavior in impeller of centrifugal pump, a centrifugal pump with five different blade profiles impellers are studied numerically. The impellers with five different blade profiles (single arc, double arcs, triple arcs, logarithmic spiral and linear-variable angle spiral) were designed by the in-house hydraulic design code using geometric parameters of IS 150-125-125 centrifugal pump. The experiments of the centrifugal pump have been conducted to verify numerical simulation model. The numerical results show that the blade profile lines has a weak effect on cavitation inception near blade inlet edge position, however it has the key effect on the development of sheet cavitation in impeller, and also influences the distribution of sheet cavitation in impeller channels. A slight changing of blade setting angle will induce significant difference of cavitation in impeller. The sharp changing of impeller blade setting angle causes obvious cavitation region separation near the impeller inlet close to blade suction surface and much more flow loss. The centrifugal pump with blade profile of setting angle gently changing (logarithmic spiral) has the super cavitation performance, which means smaller critical cavitation number and lower vapor cavity volume fraction at the same conditions.

• Tribology and Lubricants
• /
• 제24권6호
• /
• pp.332-337
• /
• 2008

This paper presents the surface defect analysis based on the experimental investigation of scribed glasses. The scribing process by a diamond wheel cutter is widely used as a reliable and inexpensive method for sizing of glass sheets. The wheel cutter generates a small median crack on the glass surface, which is then propagated through the glass thickness for complete separation. The surface contour patterns in which are formed during a scribing process are strongly related to wheel cutter parameters such as wheel tip surface finish, tip angle and wheel diameter, and cutting process parameters such as scribing pressure, speed and tooling technique. The scribed surface of a glass sheet provides normal Wallner lines, which represent regular median cracks and crack propagation in glass thickness, and abnormal surface roughness patterns. In this experimental study, normal and abnormal surface topographic patterns are classified based on the surface defect profiles of scribed glass sheets. A normal surface of a scribed glass sheet shows regular Wallner lines with deep median cracks. But some specimens of scribed glass sheets show that abnormal surface profiles of glass sheets in two pieces are represented by a chipping, irregular surface cracks in depth, edge cracks, and combined crack defects. These surface crack patterns are strongly related to easy breakage of the scribed glass imposed by external forces. Thus the scribed glass with abnormal crack patterns should be removed during a quality control process based on the surface defect classification method as demonstrated in this study.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 추계 학술발표회
• /
• pp.581-590
• /
• 2008

A SWP method is a revolutionary dewatering method. The conventional dewatering method, deep-well method, had ever occurred a civil appeal caused by the well depletion in compliance with the reduction of the groundwater level over a wider area considerably by the deep-well pumping from homogeneous sand-layer ground for a dry-work, while pump groung excavation working in Sendai city, Japan 10 years ago. it'd developed with the problematic proposal to find the new method which can lower the groundwater level only within the sheet pile without any reduction of groundwater outside of the sheet pile and until currently steady improvement came. It's been confirmed with plenty of executional results that there was almost no decreasing of water-level from surroundings, over so many construction-sites including vertical shafts which completely does not enter into non-water permeable layer and pumping ground etc. The SWP method in this time has been introducing initially and carried into a the execution tentatively at a construction-site and made a various result get through the execution.

• 조명전기설비학회논문지
• /
• 제25권6호
• /
• pp.57-67
• /
• 2011

Purpose of this study is to find the mitigation method of magnetic field by finite length multi-conductors such as indoor distribution lines and to be applicable to design of the distribution lines. For this purpose, exact formula about the components $B_x$, $B_y$, $B_z$ of magnetic field need in case of straight line-conductor with finite length forward any direction. In this study simple formula of the components were deduced and by using these formula magnetic fields for various models of line-configurations were calculated. And also a calculation method of induced currents in conductive shield was presented and using this method, programing of calculation is relatively easy and calculation time is short. The magnetic field after cancellation by these induced currents was calculated. All of calculations were performed by Matlab 7.0 programs. Through the calculation results it could be obtained followings for the mitigation of magnetic fields. The separation between conductors ought to be smaller than smaller as possible. In case of 3-phase, delta configuration is more effective than flat configuration. In case of 3-phase, unbalanced currents ought to be reduced as possible.. In case of more than two circuits of 3-phase, adequate locations of each phase-conductor such as rotating configuration of 3-phase conductors are more effective. The magnetic shielding effect of the conductive shielding sheet is very high.

• 멤브레인
• /
• 제32권2호
• /
• pp.109-115
• /
• 2022

본 연구에서는 용매로 침액되었을 시 전반적으로 더 균일한 상전이법 기반 평막 제조 시 주로 사용되는 부직포 지지체의 영향을 분석하였다. 도프용액의 점도가 낮을 경우 용액이 부직포층으로 쉽게 침투하여 불균일한 막이 형성되는 것을 확인하였으며, 이를 방지하기 위해 부직포층을 유기용매로 침액하는 기법을 도입하였다. 부직포층이 유기 분리막이 생성되는 것을 확인하였으며, 수투과 및 용매투과율도 향상하는 것을 알 수 있었다. 부직포 침액의 영향은 낮은 점도에서 확연하게 나타났으며, 고분자용액의 점도가 높은 경우 침액 여부에 관계없이 동일한 성능을 얻을 수 있었다.

• 한국산학기술학회논문지
• /
• 제14권6호
• /
• pp.3089-3095
• /
• 2013

흡음재로 널리 사용되는 헤드라이너는 발포성 폴리우레탄(PU foam)과 유리섬유(Glass Fiber,GF) 로 구성된 복합재료로, 제품의 생산 공정을 거치는 동안 부산물 형태의 폐기물이 발생한다. 헤드라이너 폐기물에 대한 효과적인 재활용을 위해 헤드라이너 구성성분에 대한 분리공정이 중요한 문제점이다. 헤드라이너에 대한 열분석결과에 의하면 중량의 감량 비율은 $400^{\circ}C$까지의 온도범위에서는 발포성 폴리우레탄 > 비발포성 폴리우레탄 > 부직포 > 1st layer > 유리섬유의 순으로 감량이 증가하는 결과를 보이고 있다. HDPE, LLDPE, PP 그리고 Master Batch 에 첨가제 형태로 폐 스크랩 첨가하여 sheet를 제작한 후 DSC 특성을 분석한 결과 PP를 제외한 다른 물질들에서는 결정화에 따른 발열전이가 나타나지 않는 것을 확인 하였다.

• 멤브레인
• /
• 제22권2호
• /
• pp.128-134
• /
• 2012

본 연구에서는 hydroxy polyimide (HPI)로 용매 증발법에 의해 제조가 되었다. 비다공성막의 기체투과성능측정 결과로써, $CO_2$ 투과도는 약 85 Barrer이고, $CO_2/N_2$선택도는 23으로 측정되었다. 고분자, 용매, 비용매-첨가제의 3성분계 시스템을 도입하여 평막과 중공사막을 제조하였고, 모폴로지와 기체투과성능을 전계방출형전자주사현미경과 버블플로우메타로 측정하였다. 평막과 중공사막에서 $CO_2$투과도와 $CO_2/N_2$ 선택도는 각각 18.28 GPU, 70 GPU를 6.72, 8.63으로 나타남을 확인하였다. 중공사막이 평막보다 기체투과특성이 우수하다는 것을 확인하였다.

• Membrane and Water Treatment
• /
• 제8권4호
• /
• pp.381-393
• /
• 2017

The inorganic components in tobacco sheet extract have significant influence on the sensory taste of the cigars and the harmful component delivery in cigarette smoke. To identify the contributions of the divalent inorganic components on harmful components delivery in cigarette smoke, a self-made selective electrodialysis was assembled with monovalent ion-selective ion exchange membranes. The influences of current density and extract content on the desalination performance were investigated. Result indicates that the majorities chloride, nitrate, and sulfate ions were removed, comparing with 50-60% of potassium and only less than 10% of magnesium and calcium ions removed in the investigated current density. The permselectivity of the tested cations across the Selemion CSO cation exchange membranes follows the order: $K^+>Ca^{2+}>Mg^{2+}$. A current density of $15mA/cm^2$ is an optional choice by considering both the energy consumption and separation efficiency. When the extract contents are in the range of 7%-20%, the removal ratios the potassium ions are kept around 60%, while the removal ratios of the calcium and magnesium ions fluctuate in the range of 16-27% and 8-14%, respectively. The tobacco smoke experiments indicated that the divalent metal ions have dual roles for the harmful component delivery in cigarette smoke. The divalent potassium and calcium ions were unfavorable for the total particulate matter emission but beneficial to decrease the HCN delivery in the mainstream cigarette smoke. The selective electrodialysis is a robust technology to decrease the harmful component delivery in cigarette smoke.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2011년도 추계 학술논문 발표대회
• /
• pp.89-94
• /
• 2011

In this research, among thermoplasticity plastic raw material that recycling is possible polyolefine(TPO) and polyvinyl chloride(PVC) as target recycling plan examine wish to. It is polyolefine(TPO) and polyvinyl chloride(PVC)) is mediocrity material that there are a lot of amount useds among plastic material and it is material that recycling is also activated most. Long term made first new regulation raw material, by-product raw material happened at process of production at second factory and third time to examine recycling plan of this material divides this as raw material that pass through process separation and pelet Tuesday and analyzed each special quality removing each removed waste after is used. Measure tension strength and ext. heightening gradually mixing proportion of refreshing resources on standard Sample manufactured as new raw material and application examined possibility availability to single fly system.