• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.251-256
• /
• 1999

"Ploughing" on the flank face of the tool in the metal cutting process is due to the tool in the metal cutting process is due to the finite edge radius of the tool and due to the development of flank wear. Because of the high stresses near the cutting edge, elastic-plastic deformation would be caused between the tool and the machined surface over a small area of the tool flank. The deformation would affect the roughness of the machined surface. Recently, some attempts have been made to predict the surface roughness, but elastic-plastic effect due to ploughing in the cutting process has not been considered. The research has analyzed mechanism of the ploughing of the cutting process using contact mechanics. Tool and workpiece material properties have been taken into account in the prediction of the surface roughness. The surface roughness has been simulated by the surface-shaping system. The results between experiment and simulation have been compared and analyzed. analyzed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.569-572
• /
• 2003

In VLM-ST process, the fine detailed shape processing process is needed due to the use of thick sheets for layers. The developed process perform the fine detailed shape processing in VLM-ST parts using non-contact hot tool. To predict the heat-affected zone and temperature distribution of VLM-ST parts in detailed shaping, the heat flux from the tool to the surface was calculated for the finite element analysis by modeling the tool as a heat source of radiation. The dominant process parameters such as the radiated heat input, the tool speed, and the gap between the tool tip and the foam sheet (tool height) were considered in the analysis. The results showed a good agreement with the experiments.

• 한국기계가공학회지
• /
• 제20권1호
• /
• pp.16-24
• /
• 2021

A laser-engineered net shaping (LENS) process is a representative directed energy deposition process. Deposition characteristics of the LENS process are greatly dependent on the process parameters. The present paper preliminarily investigates deposition characteristics of Inconel 718 superalloy on S45C structural steel using a LENS process. The influence of process parameters, including the laser power and powder feed rate, on the characteristics of the bead formation and the dilution in the vicinity of the deposited region is examined through repeated experiments. A processing map and feasible deposition conditions are estimated from viewpoints of the aspect ratio, defect formation, and the dilution rate of the deposited bead. Finally, an appropriate deposition condition considering side angle, deposition ratio, and buy-to-fly (BTF) is predicted.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 추계학술대회논문집 - 한국공작기계학회
• /
• pp.230-235
• /
• 2000

In this paper, a surface generation model is presented to simulate surface roughness profile in turning operation. The simulation model takes into account the effect of tool geometry, process parameters, rotational errors of spindle, and the relative vibration between the cutting tool and workpiece. The surface roughness profiles are simulated based on the surface-shaping system. The model has been verified by comparing the experimental values with the simulation values. It is shown that the surface simulation model can properly predict the surface roughness profile.

• 한국생산제조학회지
• /
• 제8권5호
• /
• pp.25-29
• /
• 1999

Machining process introduces thermal deformation of a cutter which affects the surface finish of the workpieces. By measuring the temperature distribution f the cutter thermal stress and deformation of the cutter are simulated. In addition surface roughness of workpiece is simulated by the surface-shaping system. The result shows that thermal deformation deteriorates the surface roughness.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1998년도 추계학술대회 논문집
• /
• pp.97.2-101
• /
• 1998

Machining process introduces thermal deformation of a cutter, which affects the surface finish of the workpieces. By measuring the temperature distribution of the cutter, thermal stress and deformation of the cutter are simulated. In addition, surface roughness of workpiece is simulated by the surface-shaping system. The result shows that thermal deformation deteriorates the surface roughness.

• 한국생산제조학회지
• /
• 제5권3호
• /
• pp.66-72
• /
• 1996

The applicability of a new method, termed the whirling motion concept, for the improvement of the surface finish in milling three-dimensional sculptured surfaces has been investigated. A method for implementing this concept o conventional NC machines that utilize a suitably configured attachment has been proposed. The tool path equation for the ball-end milling process, based on the surface-shaping system, has been obtained. Both results of the computer simulation and the experiment verified the proposed approach.

• 한국기술혁신학회:학술대회논문집
• /
• 한국기술혁신학회 1999년도 추계학술대회
• /
• pp.163-177
• /
• 1999

전통적 혁신 이론에서 과학과 기술은 공공재와 지식으로 다루어지며, 이러한 관점은 선형모델과 기술 결정론을 자연스럽게 도출시킨다. 그러나 과학과 기술을 새롭게 규정하는 신혁신 이론에서는 기술의 사회적 형성을 강조하며, 선형 모델에서 탈피하여 혁신과정의 상호작용, 네트워크, 시스템 측면을 포섭하고 있다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.305-308
• /
• 2001

Powder injection molding (PIM) uses the shaping advantage of injection molding but is applicable to metals and ceramics. This process combines a small quantity of polymer with an inorganic powder to form a feedstock that can be molded. After shaping, the polymeric binder is extracted and the powder is sintered often to near-theoretical densities. Accordingly, PIM delivers structural materials in a shaping technology previously restricted to polymers. The process overcomes the shape limitations of traditional powder compaction, the costs of machining, the productivity limits of isostatic pressing and slip casting, and the defect and tolerance limitations of casting. The 17-4 PH stainless steel powders with average diameter of $10{\mu}m$ were injection-molded into flat tensile specimens. Sintering of the compacts was carried out at the various temperatures ranging from 900 to $1350^{\circ}C$. Sintering behavior of the compacts and tensile properties of sintered specimens were investigated.

• 소성∙가공
• /
• 제14권3호
• /
• pp.245-250
• /
• 2005

Recently, micro machining technology for high precision mold becomes more interested for mass production of high performance optical parts micro-grooved on the surface, which is under very active development due to its effectiveness in the view point of optical performance. Mechanical micro machining technology now has more competitiveness on lithography, MEMS or LIGA processes which have some problems to fabricate especially cylinder type of groove in such as lenticular lens for illumination angle modulation system. In this study. a lenticular lens mold with U-type micro groove is fabricated making utilizing of the benefit of the mechanical micro machining technology. A shaping machining process is adapted using 3 axis degree of freedom micro machining system and single crystal natural diamond tool. A brass and a electroless nickel materials are used for mold fabrication. Machining force, chip shape and machined surface are investigated from the experiment and an optimal machining condition is found based on the examined problems from the micro cutting process.