• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.1
• /
• pp.95-103
• /
• 2015

This paper presents the effects of the tool shape on the geometrical characteristics of flat end-milled side walls. A tool shape is characterized by such parameters as helix angle, number of cutting edges, and diameter. The geometrical characteristics of the side walls are represented by the surface profiles in the feed and axial directions, which are orthogonal to each other. The geometrical defects in each direction are estimated based on the instantaneous apparent cutting areas, which are represented by the interference area between the tool and workpiece and that between the cutting edge and workpiece. It is confirmed that a geometrical defect in the feed direction is formed when the tool leaves the workpiece and the curvature of the tool path changes. Defects in the axial direction are also found in the side walls, except for the defect zone in the feed direction. An up-cut using an end-mill with a steeper helix angle, a greater number of cutting edges, and a smaller diameter are thus found to improve the geometrical accuracy of end-milled side walls.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.3 no.2
• /
• pp.25-31
• /
• 2004

Machinability in metal cutting processes depends on cutting input conditions such as cutting velocity, feed rate, depth of cut, types of work material and tool shape factors. In this study, to assess chip breaking characteristics of a turning process, an equivalent oblique cutting system to this has been established. And the equivalent effective rake angle was determined using side rake angle, back rake angle and side cutting edge angle of the tool. A non-dimensional parameter, Chip breaking index(CB), was used to assess Chip breaking characteristics of chip in conjunction with the equivalent effective rake angle. In case of positive rake angles of the equivalent effective rake, the back rake angle has little effect on the chip breaking characteristics however, in case of negative ones, the side rake angle has some effect on Chip breaking characteristics.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.1
• /
• pp.59-65
• /
• 2014

To obtain an elliptical trajectory at the cutting edge during elliptical vibration cutting, sinusoidal voltage excitations of two piezoelectric actuators have commonly been used. In this study, PWM excitation, which is relatively simple to generate, was employed and its characteristics were investigated. In experimental and analytical analyses, we found that for PWM excitation, the integer-multiple frequencies of the excitation voltage distorted the shape of the elliptical trajectory, whereas at a duty ratio(DR) of 50%, the distortion of the elliptical trajectory was minimized due to disappearance of the first overtone. When the magnitude of the maximum excitation voltage was maintained at the same level for both PWM and sinusoidal excitation, PWM (DR=50%) excitation produced a greater vibration amplitude than sinusoidal excitation but resulted in more rapid saturation of a high-frequency power amplifier.

• IE interfaces
• /
• v.18 no.3
• /
• pp.247-252
• /
• 2005

In the automated production environment in the present days, the minimization of manual operation becomes a very important factor in increasing the efficiency of the production system. The exit burr produced through the milling operation on the edge of workpiece usually requires manual deburring process to enhance the level of precision of the resulting product. So far, researchers have developed various methods to understand the formation of exit burr in cutting process. One method to analytically identify the formation of exit burr was to use the geometrical information of CAD and CAM data used in automated machining. This method, in turn, generated the information resulting from the analysis such as burr type, cutting region, and exit angle. Up to now, the geometrical data were restricted to the single feature and single path. In this paper, a method to deal with the complicated geometric features such as line segment, arc, hole, and spline will be presented and validated using the field data. This method also deals with the complex workpiece shape which is a combination of multiple features. As for the cutting path, multiple tool path is analyzed in order to simulate the real cutting process. All this analysis is combined into a Windows based software and real data are used to validate the program in the conclusion.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.1466-1469
• /
• 2004

Micro spherical lens mold processing method based on mechanical one completes a spherical shape by setting a diamond tool of hundreds $\mu$m radius on spins with high speed and then using Z-axis vertical feeding motion like the fabrication of micro drilling. In this method, we can see unprocessed parts shaped like cylinder and cone and check increasing chatter marks and burrs by setting errors of the central axis of rotation on the edge of the tool. That is why this method doesn't suit for the optical lens mold. In this paper presents unprocessed parts are disappeared and chatter marks and burrs are decreased from centre of the lens after using Run-out measuring and setting system on run-out occurred from setting tool. Also the fabrication characteristics of 6：4 Brass, A1601, PMMA are compared and analyzed, establishing the optimum machining condition on each material.

• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.11
• /
• pp.1088-1094
• /
• 2006

In this paper, an auto path generation and an active compliance grinding control using 3-axis farce sensor are presented. These control algorithms enable the grinding robot to follow unknown path of various workpiece shape pattern. The robot is able to go grinding along unknown paths by position controller managing tangential direction angle and cutting speed, with only information about the start position and the end position. Magnitude and direction of normal force are calculated using force data that go through low pass filter. Moreover, normal and tangential directions are separated for force control and velocity control, respectively.

• International Journal of Internet, Broadcasting and Communication
• /
• v.9 no.2
• /
• pp.48-57
• /
• 2017

In the last few years, banks have experienced more challenging market than any other times. They need to find new ways to reconnect with their customers and rebuild their trust. But in the race to the future some banks are taking clear lead. Research works show that while high perform leading banks are different, they also share some common characteristics and principles that have allowed them to move ahead to profitable growth. Cost cutting is no longer enough to succeed in tomorrow's world. Instead, the IT function needs to work shoulder-to-shoulder with the business to support the growth agenda. Therefore "C" level's attention is moving from cost reduction towards customer experience, speeding to market for new offerings, analytics and distribution channel enhancements, taking advantage of several levers that will shape the technology agenda for the high performing organization. Next generation of digital core-banking solutions will improve pre-existing capabilities, introduce new innovations and drive qualities such as flexibility and scalability to support time to market.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.7
• /
• pp.97-105
• /
• 2002

The use of rapid prototyping (RP) has reduced time to market, cut total costs and improved product quality by giving design and manufacturing teams the opportunity to verify and fine tune designs before committing them to expensive tooling and fabrication. In order to improve their unique characteristics according to the working principles, Variable Lamination Manufacturing process (VLM-ST) and corresponding CAD/CAM software (VLM-Slicer) is developed. The objective of this study is to improve the accuracy of VLM-ST process, and it can be done by offset fur cutting error correction, cutting path overrun fur sharp edge and reference shape generation for off-line stacking. It has been shown that, through the verification experiments for given practical shapes, the proposed algorithms are effective for diverse categories of three-dimensional shapes.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.8
• /
• pp.164-174
• /
• 1996

As tools for machining precision componants, end mills and ball end mills are widely used. For the end mills have longer cylindrical shape comparing dianeter, they are liable to deflect when machining and induce geometrical error and deterioration of surface roughness. To improve the stiffness and the sharpness of the cutting edge of end mill, a software for manufacturing end mills are developed. The program predicts the result of helical flute grinding and the configuration of cuting edge which is located in cylindrical surface. Furthermore to facilitate the manufacturing end mills using CNC grinding machine, the setting condition which satisfy the geometrical requirements like tool rake angle and stiffness are obtained.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.11
• /
• pp.1675-1680
• /
• 2013

Recently, the permanent magnet linear synchronous motor as low noise, high speed and high thrust force transportation system has been proposed but this motor causes an increase of material cost because of its characteristic arranging the armature on the full length of transportation lines when this system is applied to the long distance transportation system. Therefore, we suggested discontinuous arrangement method of the armature to solve this problem. However, Detent force which causes thrust force ripple generating noise, vibration and decline of performance is generated when a mover pass between the armatures. Thus, in this paper, we examined characteristic of detent force to reduce the end edge effect according to the end edge teeth's height and auxiliary teeth and suggested the shape that can the most reduce the detent force.