• Journal of Biosystems Engineering
• /
• v.6 no.2
• /
• pp.9-19
• /
• 1982

The aim of this study was to improve the startability of the diesel engine at low temperature. The specific objective was to determine the optimum type of precombustion chamber. The eight different types of precombustion chamber and two different types of the cylinder head were designed and tested by $2^7$ factorial experiments with four replications. The lowest starting temperature for first operation, the maximum output, and the specific fuel consumption at full load and overload were checked and analyzed. The results of the study are summarized as follows; 1. The lowest starting temperature was lowered as much as $2.4^{\circ}C$ and the maximum output was increased as much as 0.3 ps with respect to the difference in the relative angle of the main passageway against the piston head from 20 degree to 18 degree. 2. The lowest starting temperature and the maximum out-put were lowered as much as $3.3^{\circ}C$ and 0.3 ps respectively with respect to the difference in the angle of the cylinder head groove from 20 degree to 18 degree. 3. The lowest starting temperature and the maximum out put were lowered as much as $2^{\circ}C$ and 0.2 ps respectively with respect to the difference in the length of the precombustion chamber from 17.5 mm to 15.5mm. 4. There was no significant difference in the startability but the maximum output was increased as much as 0.2 ps with respect to the difference in the diameter of the main passageway from 4.8mm to 4.5mm. 5. The lowest starting temperature was obtained under the condition at 47 degree in the angle of the main passageway and at 18 degree in the angle of the cylinder head groove. The maximum output and the minimum specific fuel consumption was obtained under the condition at 4.5mm in the diameter of the main passageway and at 17.5mm in the length of the precombustion chamber. 6. The angle of the cylinder head groove and the main passageway appeared to the major factors affecting the startability significantly. The interaction between the diameter of the main pass ageway and the length of the precombustion chamber had an significant influence on the maximum output. So it would be recommended to study further on the interaction between two factors mentioned above by expanding their levels. 7. The optimum condition suggested by this study could lower the starting temperature by $6^{\circ}C$ compared to the conventional precombustion chambers.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.24 no.2
• /
• pp.49-55
• /
• 1982

The purpose of this study is to classify the factors influenced on the damages of head works suffered from the storm flood occurred on July 22 1980 in both Musim and Bochong rivers and to find out an integral counter measures against the causes influenced on the disaster of head works in the engineering aspect of planning, design, construction and maintenance. In this survey, number of samples was taken 25 head Works, and the counter measures against the causes of their disasters summarized was as follows, 1. In the aspect of planning a. As the flood water level after the establishment of head works is more increased than the level before setting of head works owing to having more gentle slope of river bed between the head works than nature slope of river bed. Number of head works should be reduced for the appropriate annexation of them b. In the place where head works is established on the curved point of levee, the destruction of levee becomes severe by the strong deflective current. Therefore the setting of head works on the curved point should be kept off as long as possible and in case of unavoidable circumstances the construction method such as reinforced concrete wall or stone wall filed with concrete and anchored bank revetments should be considered. 2. In the aspect of design a. As scoring phenomena at up stream is serious around the weir Where the concentration of strong current is present in such a place, up stream apron having impermeability should be designed to resist and prevent scoring. b. As the length of apron and protected bed is too short to prevent scoring as down stream bed, the design length should be taken somewhat more than the calculated value, but in the case the calculated length becomes too long to be profitable, a device of water cushion should be considered. c. The structure of protected river bed should be improved to make stone mesh bags fixed to apron and to have vinyl mattress laid on river bed together with the improvement for increasing the stability of stone mesh bags and preventing the sucked sand from the river bed. d. As the shortage of cut-off length, especialy in case of the cutoffs conneting both shore sides of river makes the cause of destruction of embankment and weir body, the culculation of cut-off length should be taken enough length based on seepage length. 3. In the aspect of design and constructions a. The overturing destruction of weir by piping action was based on the jet water through cracks at the construction and expansion joints. therefore the expansion joint should be designed and constructed with the insertion of water proof plate and asphalt filling, and the construction joint, with concaved shape structure and steel reinforcement. b. As the wrong design and construction of the weep holes on apron will cause water piping and weir destruction, the design and construction of filter based on the rule of filter should be kept for weep holes. c. The wrong design and construction of bank revetment caused the severe destruction of levee and weir body resulting from scoring and impulse by strong current and formation of water route behind the revetment. Therefore bank revetment should be designod and constructed with stone wall filled with concrete and anchored, or reinforced concrete wall to prevent the formation of water flow route behind the wall and to resist against the scoring and impulse of strong stream. 4. In the aspect of maintenance When the damaged parts occurred at head works the authorities and farmers concerned should find and mend them as soon as possible with mutual cooperation, and on the other hand public citizen should be guided for good use of public property.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.34 no.1
• /
• pp.18-39
• /
• 2016

The study pertains to reviewing and discussing of the master plan of the main buildings in the palaces of Joseon Dynasty regarding on a Feng Shui concept that has been implemented on the palace axis that is originated from the main mountain. Gyeongbokgung (景福宮) Palace is located on the northwest coner of Hanyang (漢陽) and on the tip of the main mountain which is in contrast a quite distinguishable from the location of the Fobidden city in Beijing located in the middle of a vast basin. Changdeokgung (昌德宮) Palace as well is also located on the tip of Eungbong (鷹峯), a part of Samkaksan (三角山) mountain, of which the locations were designed for the palaces to receive the benevolent force from the main mountain. The same concept was also applied to appointing the ideal location of the maJor buildings such as Jungjeon (正殿: The throne hall), Pyunjeon (便殿: The king's office) and Chimjeon (寢殿: The king and queen's residence) in the palace that must receive the benevolent force from the qui stream also originated from the main mountain, as such that the buildings have in close relationship with the king. Amisa (蛾眉砂) had been considered as an important geographical milestone of the estate where the palace is located, especially as the guiding landmark for other buildings that must be on the land axis. The land axis with the Amisa as the starting point attributed the Feng Shui as an important measure that determines the location and the shape of other buildings. The buildings location was appeared as having the conceptual buildings location as 'front office-back bedroom building (前朝後寢)' and 'three gates-three sectors (三問三朝)' as per the Rites of Zhou (周禮). On both palaces, Amisa is located on the benevolent point of the land, and the king's bed room buildings are located near the Amisa. The main offices were located on the south of the king's bed room buildings. By practicing this type of concept, consequently the king can receive the pure benevolent force first. In the case of the clearly distinguished locations of the buildings in Gyeongbokgung Palace, Chimjeon, Pyunjeon and Jungjeon were located on the same main qui stream. However, in Changdeokgung Palace where scattered qui stream is observed, the buildings are located on the scattered qui stream. The study found that the type of location of Jungjeon receives least amount of benefit from the Feng Shui but reflects primarily the king's authority rather than order and formality of the space.

• Progress in Medical Physics
• /
• v.19 no.1
• /
• pp.80-88
• /
• 2008

Recent radiotherapy dose planning system (RTPS) generally adapted the kernel beam using the convolution method for computation of tissue dose. To get a depth and profile dose in a given depth concerened a given photon beam, the energy spectrum was reconstructed from the attenuation dose of transmission of filter through iterative numerical analysis. The experiments were performed with 15 MV X rays (Oncor, Siemens) and ionization chamber (0.125 cc, PTW) for measurements of filter transmitted dose. The energy spectrum of 15MV X-rays was determined from attenuated dose of lead filter transmission from 0.51 cm to 8.04 cm with energy interval 0.25 MeV. In the results, the peak flux revealed at 3.75 MeV and mean energy of 15 MV X rays was 4.639 MeV in this experiments. The results of transmitted dose of lead filter showed within 0.6% in average but maximum 2.5% discrepancy in a 5 cm thickness of lead filter. Since the tissue dose is highly depend on the its energy, the lateral dose are delivered from the lateral spread of energy fluence through flattening filter shape as tangent 0.075 and 0.125 which showed 4.211 MeV and 3.906 MeV. In this experiments, analyzed the energy spectrum has applied to obtain the percent depth dose of RTPS (XiO, Version 4.3.1, CMS). The generated percent depth dose from $6{\times}6cm^2$ of field to $30{\times}30cm^2$ showed very close to that of experimental measurement within 1 % discrepancy in average. The computed dose profile were within 1% discrepancy to measurement in field size $10{\times}10cm$, however, the large field sizes were obtained within 2% uncertainty. The resulting algorithm produced x-ray spectrum that match both quality and quantity with small discrepancy in this experiments.

• Journal of the Korea Concrete Institute
• /
• v.22 no.6
• /
• pp.851-858
• /
• 2010

In this study, waste glass and bottom ash were used as basic materials in order to secure a recycling technology of by-products which was mostly discarded and reclaimed. In addition, because softening point of waste glass is less than $700^{\circ}C$ and bottom ash includes combustible material, it was possible to manufacture low-temperature sintering lightweight aggregates for energy saving at $800{\sim}900^{\circ}C$ that it is as much as 20~30% lower than sintering temperature of existing lightweight aggregates. Thermal conductivity of newly-developed lightweight aggregates was 0.056~0.105W/m. K and its porosity was 40.36~84.89%. A coefficient of correlation between thermal conductivity and porosity was -0.97, it showed very high negative correlationship. With this, we were able to verify that porosity is key factor to affect thermal conductivity. Microstructure of lightweight aggregates by $CaCO_3$ content and replacement ratio of bottom ash in the variation of temperature were that $CaCO_3$ content increased along with pore size while replacement ratio of bottom ash increased as pore size decreased. Specially, most pores were open pore instead of closed pore of globular shape when replacement ratio of bottom ash was 30%, and pore size was small about 1/10~1/5 as compared with case in bottom ash 0~20%. In addition, open pore shapes were remarkably more irregular form of open pore in $900^{\circ}C$ than $700^{\circ}C$ or $800^{\circ}C$ when replacement ratio of bottom ash was 30%. We reasoned hereby that these results will influence on absorption increase, strength and thermal conductivity decrease of lightweight aggregates.

• Journal of Bio-Environment Control
• /
• v.26 no.2
• /
• pp.123-132
• /
• 2017

This study was aimed to investigate the effect of 1)irradiation with several different ratios using red, green, and blue LEDs and 2)various pulsed light irradiation with 50% duty ratio using red and blue LEDs on the growth and morphogenesis of three lettuce cultivars (Lactuca sativar L. cv. 'Jukchukmeon', 'Lolo Rosa', and 'Grand Rapid') in hydroponics culture system for 4 weeks after transplanting. Seeds were sown in rock-wool plug trays and they were placed in a culture room which was controlled at $23{\pm}1^{\circ}C/18{\pm}1^{\circ}C$ temperature and 50-60/70-85% for day and night, respectively, during cultivation period. Irradiated RGB ratios with LEDs were 6:3:1, 5:2.5:2.5, 3:3:4, 2:2:6, and 1:1:8 with $110{\pm}3{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ PPFD on the surface of cultivation bed. The frequencies of pulsed lighting was 50, 100, 500, 1,000, 5,000, 10,000, 25,000Hz (20, 10, 0.1, 0.04 ms) with red and blue LEDs and 50% duty ratio. At the RGB ratio of 6:3:1, the average fresh weight of 'Jukchukmeon' was significantly higher than that of other RGB treatments, but no significant difference compared to the fluorescent treatment. The average fresh weight at 1:1:8 RGB ratio in 'Lolo Rosa' was significantly lower than that of other RGB treatments. Leaf number and fresh weight of 'Grand Rapid' were significantly lower in the control and 1:1:8 RGB treatments, compared to the other RGB treatments. As the ratio of blue light increased, leaf length decreased and leaf shape became round in three lettuces. Although there is little change in growth, it could not be found any tendency to affect the growth and morphogenesis of three lettuces caused by increasing or decreasing frequency of pulsed lighting with 50% duty ratio at the $72{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ PPFD.

• Applied Microscopy
• /
• v.40 no.2
• /
• pp.65-71
• /
• 2010

Kribensis, Pelvicachromis pulcher is a teleost belonging to Cichlidae. The oogenesis was investigated by light microscope. The ovary was located between intestine and air bladder, a yellowish and ellipsoidal shape with the major axis 20mm and the minor axis 5 mm. Cytoplasm of oogonia in early stage was basophilic and many nucleoli were located at inside of nuclear membrane. In primary oocytes, yolk vesicles were distributed only in the marginal area and egg envelope was not formed on the outside of an egg. In secondary oocytes, the egg envelope was formed and yolk vesicles in the cytoplasm were increased than the earlier stage. The basophilic substance of cytoplasm was changed to acidic. Some yolk vesicles started forming small yolk mass except the surrounding nucleus. In case of matured egg, size of egg were increased. The yolk vesicles were changed to yolk mass in accordance with development. The yolk mass contained crystal-like structures. In conclusion, the oogenesis of Pelvicachromis pulcher was summarized by the increase in cell size, the formation and the accumulation of yolk, and the decrease of basophilic substance in the cytoplasm. The oogenesis of Coreoleuciscus splendidus is similar with other teleost. But there were differences in distribution of yolk vesicle and yolk mass containing cristal-like structures.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.39 no.2
• /
• pp.29-39
• /
• 2011

Recent interests in the quality of urban space have raised awareness on the role and importance of landscape planning. Although laws and guidelines are officially ready to be imposed as for landscape planning, we do not have concrete materials that can be utilized in the course of practices. The aim of this paper in this regard is to disclose the possible difference in awareness on 'visual landscape control elements' among experts engaged with urban space planning. The expert groups are distinguished to three which are for a planning, design and engineering and the survey is made by questionnaires. The results are analyzed through basic technology statistics in SPSS and independent-sample t-test provided. The survey is done by tens of 'control elements' and the result is that specially, group 1 and group 2 in mixed landscape has the most discrepancy in awareness on those elements but relatively, they has less discrepancy in awareness on compare with other groups through all landscape area. In case of artificial landscape and mixed landscape in 'landscape controled area', the result for comparing between G1 and G2 is that there are the most discrepancy in awareness which are 7 control elements. In case of mixed landscape in 'landscape promoted area', there are 4 control elements for discrepancy in awareness between G2 and G3 which is quite different. The control elements which show the most discrepancy in awareness is height, floor space and building to land ratio in order. The shape elements has only discrepancy in awareness for comparing between G1 and G2 of artificial landscape in 'landscape controled area'. In terms of the average evaluation score of the appropriateness of these control elements, G1 seems to appreciate the role of these elements in systematic landscape planning more than the other group does. In other words, relatively low scores are given by G2 as for the overall functionality of visual landscape control elements. The texture, floor space and building of land ratio has low evaluation score for all area and types. It means that it should reverify for appropriateness of performance for landscape planning as visual landscape control elements.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.38 no.3
• /
• pp.75-82
• /
• 2010

This study formed an estimation of the visual characteristics of urban bridges in Yanghwaro in the Gyeongui Railroad Area using a landscape simulation. Existing theses have formerly only suggested directions for design based on visual preference, but there is as yet no research on the practical process of landscape design. As a result, it is difficult to directly apply this to bridge design. This study found a potential bridge site and presented a direction for bridge design in order to improve the image of the surrounding urban landscape by surveying the visual effects and landscape preferences of different bridge types. An urban landscape was produced using a landscape simulation model and was made the background for the survey. Five bridge types--Girder, Arch, Truss, Cable and Suspension--were selected and presented. The shapes of the bridges were selected based on the floor plan. The results of this study are as follows. In a preference analysis, every bridge except Girder was evaluated as a positive influence. When rating the image, 'artificial' was rated significantly higher than other traits when assessing the background image. When the Girder Bridge was introduced, 'stable' and 'orderly' were both rated highly while 'stable', 'beautiful', 'orderly' and 'interesting' were high with the introduction of the Arch Bridge. 'Beautiful', 'stable', and 'orderly' were given a high value in the introduction of the Truss Bridge and every image except 'natural', 'harmony' and 'orderly' were highly rated in the introduction of the Cable Bridge. Further, every image but 'natural' was highly rated with the introduction of the Suspension Bridge. Based on the analysis of the landscape, there is a difference in preference before and after modeling a bridge type, while the bridge itself is an influence when it is the main object of the simulated scene. This study researched only the shape of the bridge as a part of the landscape but other elements such as stability, economics, and construction are also factors in the design of a bridge. Stability, economics, construction and other factors must be considered when selecting a bridge type in the future.

• Investigative Magnetic Resonance Imaging
• /
• v.13 no.1
• /
• pp.74-80
• /
• 2009

Purpose : To evaluate the characteristic MR imaging findings of Langerhans cell histiocytosis (LCH) in the skull and to compare them with those of plain radiography and computed tomography. Materials and Methods : A total of 10 lesions in 9 patients (Age range; 5-42 years, Mean age; 18, all women) with Langerhans cell histiocytosis in the skull were included in our study. Nine lesions in nine patients were histologically confirmed by surgery or fine needle aspiration biopsy. All patients performed with MRI, and plain radiography and CT scan were done in 7 patients (8 lesions). Two experienced neuroradiologists reviewed the radiological examinations independently with attention to location, size, shape and nature of the lesions in the skull and compared the extent and extension of the lesions to adjacent structures. Results : The lesions were distributed in all of the skulls without predilection site. On MRI, the masses were shown as well-enhancing soft tissue masses (10/10) mainly in diploic spaces (8/10) with extension to scalp (9/10) and dura mater (7/10). Dural enhancement (7/10) and thickening (4/10) were seen. The largest diameter of the soft tissue masses ranged 1.1 cm to 6.8 cm, shaped as round (5/10) or oval (5/10). On CT scans, the lesions were presented as soft tissue masses involving diploic space (6/8) and scalp extension (7/8) were also well visualized. Although bony erosion or destruction was more clearly seen on CT rather than those of MRI, enhancement of soft tissue masses and dura were not well visualized on CT. In contrast, all of the lesions in LCH were seen as punched out (4/8), beveled-edge appearance (4/8) osteolytic masses in plain radiography, but scalp and dural extension could not be seen. Conclusion : Characteristic MR findings in patients with LCH are soft tissue mass in diploic space with extension to dura and scalp, and MRI would be better imaging modality than plain radiography or CT.