• Asian-Australasian Journal of Animal Sciences
• /
• v.16 no.1
• /
• pp.50-56
• /
• 2003

An experiment was carried out to compare the body weight, shank length, rectal temperature, comb area, abdominal fat, blood parameters and bone traits of capon, slip and intact birds in Taiwan country chicken cockerels. One hundred and sixty-six Taiwan country chicken cockerels were randomly assigned to caponized or intact male groups. Caponized birds were surgically altered at 10 weeks old and raised to 28 weeks old. At 28 weeks of age, the capons were separated into capon and slip groups, depending on the atrophy of the comb and wattle in size. The results showed that body weight and shank length in slips were significantly (p<0.05) greater than in intact birds. Intact birds had the highest (p<0.05）feather scores and the lowest (p<0.05) rectal temperature. Compared with intact birds and slips, capons had a significantly (p<0.05) smaller comb area. Bone percentage, stress and cortical thickness, and bone and ash calcium content and plasma testosterone concentration, in intact birds were the highest (p<0.05) followed by slips and capons. However, intact birds had the lowest (p<0.05) plasma ionized calcium and phosphorus concentrations. Bone and ash manganese contents in capons were significantly (p<0.05)lower than those in others. These findings support the hypothesis that androgenic effects on secondary sexual characteristics are stronger than anabolic growth promoting response. Androgens can directly influence calcium fluxes in male chickens. Caponized caused a reduction in the bone percentage, stress, cortical thickness and bone calcium content.

• Journal of Welding and Joining
• /
• v.17 no.3
• /
• pp.79-89
• /
• 1999

The study was carried out to examine in more detail metallurgical and mechanical properties of brazed joints of diamond cutting wheel. In this work, shank(mild steel) and sintered bronze-base tips were brazed with three different filler materials(W-40, BAgl and BAg3S). The machine used in this work was a high frequency induction brazing equipment. The joint thickness, porosities and microstructure of brazed joints with brazing variables(brazing temperature, holding time) were evaluated with OLM, SEM, EDS and XRD. Bending(torque) test was also performed to evaluate strength of brazed joints. Further wetting test was performed in a vacuum furnace in order to evaluate the wettability of filler metals on base metals9shank and tips). The brazing temperature had a strong influence on the joint strength and the optimum brazing temperature range was about $700~850^{\circ}C$ for the bronze/steel combinations. The strength of the brazed joint was found to be influenced by the three factors : degree of reaction region, porosity content, joint thickness. The reaction region was formed in the bronze-base tip adjacent to the joint. The reaction region resulted in a bad influence on the strength due to the formation of Cu5.6Sn, CuZn4, $\beta(CuZn)$ and CdAg, etc. Porosities increased as brazing variables(brazing temperature, holding time) increased, and the brazed joints with porosities of less than about 3-5% had an optimum strength for the bronze-base tip.

• Proceedings of the KOSOMBE Conference
• /
• v.1998 no.11
• /
• pp.147-148
• /
• 1998

In this paper, we developed the process for depth-probe type silicon microelectrode arrays. The process consists of four mask steps only. The steps are for defining sites, windows, and for shaping probe using plasma etch from above, and for shaping using wet etch from below, respectively. The probe thickness is controlled by dry etching, not by impurity diffusion. We used gold electrodes with a triple dielectric system consisting of oxide/nitride/oxide. The shank of the probe taper from 200um to tens of urn tip and has 30 um thickness.

• Korean Journal of Poultry Science
• /
• v.18 no.3
• /
• pp.197-208
• /
• 1991

This study was conducted to estimated the genetic and phenotypic correlations between economic traits and certain other traits in Korean Native Ogol fowl The data analysis were the record of 450 pullets bred from 150 dams and 20 sires of Korean Native Ogol fowl at Chungnam National University from June 18, 1987 to April 6, 1989. The results obtained are summarized as follows ： 1 The genetic correlation coefficients of the economic traits and body shape components were as follows ： between body weight and shank length, breast width. breast girth, tibia length were 0.210~0.788, 0.231~0.826, 0.610~0.995 and 0.096~0.503 between age at first egg and shank length, breast width, breast girth, tibia length were 0.555~0.626, 0.149~0.270, 0.370~0.445 and 0.014-0.124. between number of egg production and shank length, breast girth, tibia length were -0.446~-0.167, -0.162~-0.320, 0.076~0.336 and 0.203~0.312 ： between egg weight and shank length, breast width, breast girth, tibia length were 0.132~0.498, 0.236~0.410, 0.148~0.775 and -0.019~0.593, respectively. 2. The genetic correlation coefficients of the economic traits and egg components were as follows ： between body weight and albumen weight, yolk weight, shell weight were 0.083~0.591, 0 110~0.541 and 0.336~0.782 between age at the first egg and albumen weight, yolk weight, shell weight were 0.476-0.692, 0.265~0.631 and 0.420~0.519 between number of egg Production and albumen weight, yolk weight, shell weight were -0.578~-0.240, -0.255~-0.060, -0.477~-0.313. between egg weight and albumen weight, yolk weight, shell weight were 0.825~0.939, 0.382~0.564, 0.374~0.337, respectively. 3. The genetic correlation coefficients of the economic traits and egg qualifies were as follows ： between body weight and egg shape index, shell thickness, albumen height, Haugh units were 0.215~0.367, 0.248~0.650, 0.161~0.624, 0.157~0.449. between number of egg production and egg shape index, shell thickness, albumen height, Haugh units were -0.384~-0.207, -0.557~-0.306, -0.555~-0.198, -0.582~-0.074 between egg weight and egg shape index, shell thickness, albumen height, Haugh units were 0.276~0.697, 0.290~0.627, 0.238~0.538, -0.207-0.020, respectively. 4. The genetic correlation coefficients of egg compositions and egg qualities were as follows ： between albumen weight and egg shape index, shell thickness, albumen height and Haugh units were 0.110~0.584, -0.380~-0.002, 0.239~0.887 and -0.195~0.279 ： between yolk weight and egg shape index, shell thickness, albumen height and Haugh units were -0.204~0.160, 0.294~0.133, -0.049~0.133 and -0.196~-0 136 ： between shell weight and egg shape index, shell thickness, albumen height and Haugh units were 0.127~0.503, 0.127~0.476, 0.140~0.273 and -0.172~0.233, respectively.

• Conservation Science in Museum
• /
• v.17
• /
• pp.55-68
• /
• 2016

Conservation and research efforts are currently underway at the National Museum of Korea on a series of artifacts excavated from Tomb No. 9 at Seogam-ri nearly a century ago by an archaeology team from the institution's colonialera predecessor. Among these objects are a number of bronze and gilt bronze buttons. The present study explores the production techniques used in making such buttons. Both bronze and gilt bronze buttons are hemispherical in shape and are similar in external appearance. However, their shanks differ significantly in size and cross-sectional shape, some with a round cross-section while others are square. The buttons, first sorted into two groups by each type of shank, were further subdivided by size. Analysis of round shanks has found variations in design and location as well as in shank thickness. In addition, the location where round shanks attach to buttons are usually irregular in surface. Square shanks, on the other hand, are more uniform in design and location. The shanks are typically located on the backs of buttons and attach to a groove which ostensibly serves to mark the correct position. X-ray imaging has revealed that round shanks have thick borders made from metal rather than dirt or other material. The buttons themselves appear to been cast using lost-wax technique. The ways in which each shank attaches to its respective button varies based on its cross-sectional shape.

• Journal of Biomedical Engineering Research
• /
• v.22 no.2
• /
• pp.145-150
• /
• 2001

대뇌 피질에 삽입하여 깊이에 따라 신경 신호를 기록하기 위한 탐침형 반도체 미세전극 어레이(depth-type silicon microelectrode array, 일명 SNU probe)를 제작하였다. 붕소를 확산시켜 생성된 고농도 p-type doping된 p＋ 영역을 습식식각 정지점으로 사용하는 기존의 방법과 달리 실리콘 웨이퍼의 앞면을 건식식각하여 원하는 탐침 두께만큼의 깊이로 트렌치(trench)를 형성한 후 뒷면을 습식식각하는 방법으로 탐침 형태의 미세 구조를 만들었다. 제작된 반도체 미세전극 어레이의 탐침 두께는 30 $\mu\textrm{m}$이며 실리콘 건식식각을 위한 마스크로 6 $\mu\textrm{m}$ 두께의 LTO(low temperature oxide)를 사용하였다. 탐침의 두께는 개발된 본 공정을 이용해서 5~90 $\mu\textrm{m}$ 범위까지 쉽게 조절할 수 있었다. 탐침의 두께를 보다 쉽게 조절할 수 있게 됨에 따라 여러 신경조직에 필요한 다양한 구조의 반도체 미세전극 어레이를 개발할 수 있게 되었다. 본 공정을 이용해서 개발된 4채널 SUN probe를 사용하여 흰쥐의 제1차 체감각 피질에서 4채널 신경 신호를 동시에 기록하였으며, 전기적 특성검사에서 기존의 탐침형 반도체 미세전극, 텅스텐 전극과 대등하거나 우수한 신호대 잡음비(signal to noise ratio, SNR)특성을 가짐을 확인하였다.

• Animal Bioscience
• /
• v.34 no.1
• /
• pp.127-133
• /
• 2021

Objective: This study was conducted to evaluate the correlation between body size traits, carcass traits, and primal cuts in Hanwoo steers. Methods: Sixty-one beef carcasses were classified for conformation and primal cut weight. Additionally, carcass weight, fat thickness, carcass dimensions, and longissimus muscle area were determined to complement the grading. Results: The average live weight and cold carcass weight were 759 and 469 kg, respectively. The mean carcass meat, fat, and bone proportions were 551, 298, and 151 g/kg, respectively. Primal cuts weights showed significant positive correlations (p<0.001) of 0.42 to 0.82 with live weight, carcass weight, and longissimus muscle area and a significant negative correlation with carcass fat (without shank, -0.38 to -0.10). Primal cut weights were positively correlated (p<0.01) with carcass length (0.41 to 0.77), forequarter length (0.33 to 0.57), 6th lumbar vertebrae-heel length (0.33 to 0.59), 7th cervical vertebrae carcass breadth (0.35 to 0.58), 5th to 6th thoracic vertebrae breadth (0.36 to 0.65), 7th to 8th thoracic vertebrae girth (0.38 to 0.63), and coxae girth (0.34 to 0.56) and non-significantly related to cervical vertebrae length and coxae thickness. Conclusion: There was a high correlation among live weight, carcass weight, longissimus muscle area, carcass length, 7th cervical vertebrae carcass breadth, 5th to 6th thoracic vertebrae breadth, and 7th to 8th thoracic vertebrae girth of the primal cuts yield. The correlation between fat and primal cut yields was highly significant and negative. Carcass length and 7th to 8th thoracic vertebrae girth, appear to be the most important traits affecting primal cut yields.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.956-959
• /
• 2004

Recently the monitoring system of tool setting in high speed precision machining center is required for manufacturing products that have highly complex and small shape, high precision and high function. It is very important to reduce time to setup tool in order to improve the machining precision and the productivity and to protect the breakage of cutting tool as the shape of product is smaller and more complex. Generally, the combination of errors that geometrical clamping error of fixing tool at the spindle of machining tool and the asynchronized error of driving mechanism causes that the run-out of tool reaches to 3$^{\sim}$20 times of the thickness of cutting chip. And also the run-out is occurred by the misalignment between axis of tool shank and axis of spindle and spindle bearing in high speed rotation. Generally, high speed machining is considered when the rotating speed is more than 8,000 rpm. At that time, the life time of tool is reduced to about 50% and the roughness of machining surface is worse as the run-out is increased to 10 micron. The life time of tool could be increased by making monitoring of tool-setup easy, quick and precise in high speed machining tool. This means the consumption of tool is much more reduced. And also it reduces the manufacturing cost and increases the productivity by reducing the tool-setup time of operator. In this study, in order to establish the concept of tool-setup monitoring the measuring method of the geometrical error of tool system is studied when the spindle is stopped. And also the measuring method of run-out, dynamic error of tool system, is studied when the spindle is rotated in 8,000${\sim}$60,000 rpm. The dynamic phenomena of tool-setup are analyzed by implementing the monitoring system of rotating tool system and the non-contact measuring system of micro displacement in high speed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.1066-1069
• /
• 2004

Recently the monitoring system of tool setup in high speed precision machining tool is required for manufacturing products that have highly complex and small shape, high precision and high function. It is very important to reduce time to setup tool in order to improve the machining precision and productivity and to protect the breakage of cutting tool as the shape of product is smaller and more complex. Generally, the combination of errors that geometrical clamping error of fixing tool at the spindle of machining center and the asynchronized error of driving mechanism causes that the run-out of tool reaches to 3∼20 times of the thickness of cutting chip. And also the run-out is occurred by the misalignment between axis of tool shank and axis of spindle and spindle bearing in high speed rotation. Generally, high speed machining is considered when the rotating speed is more than 8,000 rpm. At that time, the life time of tool is reduced to about 50％ and the roughness of machining surface is worse as the run-out is increased to 10 micron. The life time of tool could be increased by making monitoring of tool-setting easy, quick and precise in high speed machining center. This means the consumption of tool is much more reduced. And also it reduces the manufacturing cost and increases the productivity by reducing the tool-setup time of operator. In this study, in order to establish the concept of tool-setting monitoring the measuring method of the geometrical error of tool system is studied when the spindle is stopped. And also the measuring method of run-out, dynamic error of tool system, is studied when the spindle is rotated in 8,000 ∼ 60,000 rpm. The dynamic phenomena of tool-setup is analyzed by implementing the monitoring system of rotating tool system and the noncontact measuring system of micro displacement in high speed.

• Journal of agriculture & life science
• /
• v.51 no.6
• /
• pp.89-105
• /
• 2017

This study utilized 32,312 records of 17 linear type and 10 conformation traits(including final scores) of Hanwoo cows in the KAIA(Korea Animal Improvement Association) ('09~'10), with 60,556 animals in the pedigree file. Traits included stature, body length, strength, body depth, angularity, shank thickness, rump angle, rump length, pin bone width, thigh thickness, udder volume, teat length, teat placement, foot angle, hock angle, rear leg back view, body balance, breed characteristic, head development, forequarter quality, back line, rump, thigh development, udder development, leg line, and final score. Genetic and residual(co) variances were estimated using bi-trait pairwise analyses with EM-REML algorithm. Herd-year-classifier, year at classification, and calving stage were considered as fixed effects with classification months as a covariate. The heritability estimates ranged from 0.03(teat placement) to 0.42(body length). Rump length had the highest positive genetic correlation with pin bone width(0.96). Moreover, stature, body length, strength, and body depth had the highest positive genetic correlations with rump length, pin bone width, and thigh thickness(0.81-0.94). Stature, body length, strength, body depth, rump length, pin bone width, and thigh thickness traits also had high positive genetic correlations.