• 한국수소및신에너지학회논문집
• /
• 제26권3호
• /
• pp.287-293
• /
• 2015

The current study has investigated the effects of biodiesel blended with gasoline on the spray characteristics in a Constant Volume Combustion Chamber (CVCC). With the concentration of 5, 10, 15 and 20% by volume, biodiesel was blended with commercial gasoline and performed on the macroscopic visualization test. Pure gasoline and biodiesel were also tested as the reference. The shadowgraph technique was conducted in the constant volume chamber. The spray images were recorded by a high speed video camera with frame speed 10,000 frame per second. Fuel injection was set at 800, 1000 and 1,350 bar with the simulated speed 1,500 and 2,000 rpm. The back pressure was controlled at 20 bar. The spray angle and penetration tip were measured and analyzed by using the image processing. At the high injection pressure, the spray penetration length with the simulated speed 1,500 rpm showed that B100 was lower than GB00-20 whereas the spray penetration length with the simulated speed 2,000 rpm exhibited that GB blends and B100 were insignificantly different. Due to biodiesel concentration, its effects on spray angles were observed throughout injection periods (T1, T2 and T3). At the simulated speed 1,500 rpm, the spray angle of GB blends and B100 presented the same pattern following injection timing. In addition, when the simulated speed increased to 2,000 rpm the different spray angle of all blends disappeared at main injection (T3).

• 한국추진공학회지
• /
• 제18권6호
• /
• pp.11-18
• /
• 2014

아산화질소/에탄올 추진제 조합을 사용하는 50 N급 추력기 분사기 인접부에서 shadowgraph 기법을 사용하여 연소 유동장을 가시화하였다. 설계 작동조건에서 폭발성 점화가 일어났으며, 급격히 팽창하는 연소가스에 의해 순간적으로 소염되는 현상이 관찰되었다. 최초 점화로부터 약 83 ms 뒤 추진제 분무는 재점화 되었으며, 그로부터 약 23 ms 후 화염이 안정화되는 것이 관찰되었다. 동일한 시퀀스에서 설계 조건보다 산화제 유량을 증가시킨 경우, 소염 현상 없이 완만한 연소 압력 과도 특성을 보였으며 최초 점화로부터 약 17 ms이내에 화염 안정화가 이루어졌다. 이는 점화 직전의 연소기 내부 미연 추진제 혼합 향상에 의한 것으로 생각되었다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.905-911
• /
• 2017

공기와 물을 사용하여 인젝터의 위치와 운동량 플럭스 비가 수직유동이 횡단유동장내의 수직분사 제트에 미치는 영향을 정성적으로 연구하고 도시하였다. 운동량 플럭스 비를 고정하고 인젝터 홀의 위치를 변화시키고 역으로 인젝터 홀의 위치를 고정하고 운동량 플럭스 비를 변화시켰다. 이미지 가시화는 고속카메라를 이용하여 Shadowgraph 기법을 사용하였다. 가시화된 이미지는 밀도구배강도 이미지를 통하여 분무의 차이를 비교하였다. 장치의 x/d가 증가할수록 제트의 분열 높이가 낮아지며 분무 각도 또한 감소하는 것을 관측하였다. x/d가 0일 때는 어떠한 운동량 플럭스 비에서도 분무가 바닥과 천장에 닿게 되는 결과를 보였다.

• 한국추진공학회지
• /
• 제22권5호
• /
• pp.88-96
• /
• 2018

공기와 물을 사용하여 인젝터의 위치와 운동량 플럭스 비가 수직유동이 횡단유동장내의 수직 분사 제트에 미치는 영향을 정성적으로 연구하고 도시하였다. 운동량 플럭스 비를 고정하고 인젝터 홀의 위치를 변화시킨 후 역으로 인젝터 홀의 위치를 고정하고 운동량 플럭스 비를 변화시켰다. 이미지 가시화는 고속카메라를 이용하여 Shadowgraph 기법을 사용하였다. 가시화된 이미지는 밀도구배강도 이미지를 통하여 분무의 차이가 비교되었다. 장치의 x/d가 증가할수록 액주 기둥의 높이가 낮아지는 것을 확인하였다. x/d가 0일 때는 어떤 운동량 플럭스 비에서도 분무가 바닥 또는 천장에 닿게 되는 결과를 보였다.

• Journal of Mechanical Science and Technology
• /
• 제17권3호
• /
• pp.449-456
• /
• 2003

In this study, numerical and experimental analysis on the spray atomization characteristics of a GDI injector is performed. For numerical approach, four hybrid models that are composed of primary and secondary breakup model are considered. Concerning the primary breakup, a conical sheet disintegration model and LISA model are used. The secondary breakup models are made based on the DDB model and RT model. The global spray behavior is also visualized by the shadowgraph technique and local Sauter mean diameter and axial mean velocity are measured by using phase Doppler particle analyzer Based on the comparison of numerical and experimental results, it is shown that good agreement is obtained in terms of spray developing process and spray tip penetration at the all hybrid models. However, the hybrid breakup models show different prediction of accuracy in the cases of local SMD and the spatial distribution of breakup.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2000년도 제21회 KOSCO SYMPOSIUM 논문집
• /
• pp.194-201
• /
• 2000

This paper is intended to analyze the macroscopic behavior and transient atomization characteristics of the high-pressure gasoline injector in direct-injection gasoline engine. The global spray behavior of fuel injector was visualized by shadowgraph technique. Time-resolved droplet axial and radial velocity components and droplet diameter were measured at many probe positions in both axial and radial directions by a two-component phase Doppler particle analyzer (PDPA). In order to obtain the influence of fuel injection pressure, the macroscopic visualization and experiment of particle measurement on the fuel spray were investigated at 3,5 and 7 MPa of injection pressure under different surrounding pressure in the spray chamber. The results of this work show that the fuel injection pressure of gasoline injector in GDI engine has influence upon the mean droplet diameter, mean velocity of spray droplet, the spray tip penetration, and spray width under the elevated ambient pressure.

• 오토저널
• /
• 제14권3호
• /
• pp.102-108
• /
• 1992

To clarify the structure of a diesel spray, a transient non-evaporating diesel spray injected under different ambient pressure and different injection pressure was studied. Spray tip penet- ration and spray angle were measured by taking the high speed shadowgraph of spray and Sauter mean Diameter(SMD) was also measured by light scattering technique at different positions along the spray axis and at different time from the start of injection. The effects of the operating parameters on the spray shape and SMD were investigated. By increasing the injection pressure, the spray tip penetration and the spray angle increased and the change of the ambient pressure also resulted in the considerable change in the shape of the spray. The analysis of SMD measurement showed that the atomization is a process that continues in sp- ace and time. As the injection pressure increases SMD decreases rapidly and with the increa- se of the ambient pressure the atomization process ends faster than the lower ambient press- ure and at lower pressure the atomization process continues to much farther downstream and far afterward.

• 한국자동차공학회논문집
• /
• 제10권6호
• /
• pp.27-33
• /
• 2002

This paper presents the comparison of prediction accuracy of hybrid models. To obtain the experimental results fur comparing with the numerical results, the macroscopic and microscopic structures of the hollow-cone spray such as spray development process, spray penetration and the distribution of mean droplet size are investigated by using a shadowgraph technique and phase Doppler particle analyzer. Also, the numerical researches using various hybrid models are performed. LISA model and WAVE model are used for the primary breakup, and TAB, DDB, and RT model are used for the secondary breakup.

• 한국분무공학회지
• /
• 제23권1호
• /
• pp.9-15
• /
• 2018

Breakup lengths of circular and elliptical liquid jets in a subsonic crossflow were experimentally studied. Two circular-shaped and four elliptical-shaped plain-orifice injectors, which had different aspect ratios and orifice length to diameter ratios, were used to provide various liquid jet conditions such as steady, cavitation, and hydraulic flip. By varying the injection pressure drop from 1 bar to 6 bar, spray images were taken using a shadowgraph technique. Breakup lengths were measured and analyzed. As the aspect ratio in orifices increased, liquid column breakup lengths normalized by the equivalent diameter were reduced irrespectively of the switching of the major or minor axis to the crossflow. It was also found that when hydraulic flip developed inside the orifice, x-directional breakup lengths more decreased for both circular and elliptical liquid jets.

• 한국분무공학회지
• /
• 제12권2호
• /
• pp.115-122
• /
• 2007

The spray characteristics and drop size measurements have been experimentally studied in liquid jets injected into subsonic crossflow. With water as fuel injection velocity, injection angle and atomize. internal flows were varied to provide of jet operation conditions. The injector internal flow was classified as three modes such as a non-cavitation flow, cavitation, and hydraulic flip flows. Pulsed Shadowgraph Photography measurement was used to determine the spatial distribution of the spray droplet diameter in a subsonic crossflow of air. And this study also obtains the SMD (Sauter Mean Diameters) distribution by using Planar Liquid Laser Induced Fluorescence technique. The objectives of this research are get a droplet distributions and drop size measurements of each condition and compare with the other flow effects. As the result, This research has been showned that droplet size were spatially dependent on air-stream velocity, fuel injection velocity, injection angle effects, and normalized distance from the injector exit length(x/d, y/d). There are also different droplet size characteristics between cavitation, hydraulic flip and the non-cavitation flows.