• Tribology and Lubricants
• /
• 제30권6호
• /
• pp.370-377
• /
• 2014

The basic elements in a rotary-type scroll compressor are two identical spiral scrolls containing refrigerant gas. The pressure variations in the compression pockets of a scroll compressor change the forces acting on the orbiting scroll, and these forces affect the dynamic behavior of the compression mechanism parts. To achieve high efficiency, using a self-sealing mechanism as a tip seal mechanism is very effective. Tip seals, which are placed on top of the scroll wraps, accomplish thrust sealing. This study calculates the friction force between the tip seal and the side plate of a scroll compressor using the numerical model considered in the Reynolds equation. The calculated friction force is verified by an experiment using a pin-on-disk apparatus. A hydraulic servo valve that controls the pressure of the oil hydraulic cylinder applies the normal load for the test, and a DC servo motor controls the sliding velocity of the disk. The friction force and normal load are measured by the force sensors attached to the supporting parts. The results show that the theoretical and experimental results are similar and that the friction is influenced by the viscosity of the oil and the sliding velocity of the scroll.

• 드라이브 ㆍ 컨트롤
• /
• 제18권3호
• /
• pp.1-7
• /
• 2021

In a hydraulic control system, since a hydraulic cylinder drives a relatively large mass of an object, an external load force acts as a disturbance on the control performance of the system. Additionally, as the hydraulic system is used for a long period, there are disturbances that occur gradually, such as a drop in supply pressure because of abrasion of the pump, oil leakage from a valve, and oil leakage from a cylinder. In this study, a state feedback controller based on a linearization technique is applied. To prevent the performance degradation of the controller from the load disturbance, an Extended Luenberger observer (ELO) is used for the Extended system. The case of using the proportional controller, which is a representative linear controller, and the result of using the controller designed in this study are compared and reviewed through simulation. Also, we propose an experimental gain-setting method for a state feedback controller that can be used at industrial sites, and examine how the stability and control performance of the system changes because of the disturbance inputs through the experimental results.

• 드라이브 ㆍ 컨트롤
• /
• 제19권1호
• /
• pp.34-42
• /
• 2022

Hydrostatic transmission (HST) comprises rotary parts, shafts, valve plate, swashplate, and servo pistons. Ensuring structural stability of each part of an HST has a significant impact on product safety. In this study, the structural stability of HST in agricultural machinery and industrial vehicles was analyzed using ANSYS software. For conservative evaluation, high-pressure conditions (35.5 MPa and 2 MPa pilot pressure) were applied as load conditions. The number of grids used in the calculations ranged from 0.4 to 0.8 million depending on modeling requirements. Structural analysis was performed for essential parts and safety factor was analyzed. All major parts of HST had a safety factor of ≥ 1.5. Thus, they were judged to be structurally safe. This study provides important information for designing an HST system.

• 한국정밀공학회지
• /
• 제16권1호통권94호
• /
• pp.42-48
• /
• 1999

A control method for a robot hand grasping a object in a partially unknown environment will be proposed, where a proximate sensor detecting the distance between the fingertip and object was used. Particularly, the finger joints were driven servo-pneumatically in this study. Based on the proximate sensor signal the finger motion controller could plan the grasping process divided in three phases ; fast aproach, slow transitional contact and contact force control. That is, the fingertip approached to the object with full speed, until the output signal of the proximate sensor began to change. Within the perating range of the proximate sensor, the finger joint was moved by a state-variable feedback position controller in order to obtain a smooth contact with the object. The contact force of fingertip was then controlled using the blocked-line pressure sensitivity of the flow control servovalve for finger joint control. In this way, the grasping impact could be reduced without reducing the object approaching speed. The performance of the proposed grasping method was experimentally compared with that of a open loop-controlled one.

• 한국항공우주학회지
• /
• 제34권3호
• /
• pp.74-80
• /
• 2006

본 논문은 선형 전기모터가 유압밸브 스풀(valve spool)을 직접 움직이는 직접구동밸브 (DDV: direct drive valve) 방식 유압서보 엑츄에이터의 제어 및 고장 모니터링에 관한 것이다. 유압서보 구동장치는 밸브 스풀을 통한 유량 흐름 특성으로 인하여 비선형 운동 특성을 갖게 된다. DDV 구동장치에 관한 비선형 운동 모델을 제시하고, 이를 선형화 시켜 DDV 구동장치의 제어계 및 고장 감지계 설계에 유용하게 사용될 수 있는 단순화된 선형 모델을 제시하였다. 한편, 조종면 구동 엑츄에이터가 만족시켜야 하는 성능 그리고 안전 작동에 관한 요구조건에 대하여 논의한 후, 이를 만족시키기 위한 제어계 및 고장 감지계의 구조에 대한 논의를 한다. 3중의 다중화 구조를 갖는 유압 DDV 구동장치의 운동 특성을 해석할 수 있는 수치해석 모델이 개발되었다.

• Journal of Biosystems Engineering
• /
• 제33권2호
• /
• pp.115-123
• /
• 2008

This study was conducted to develop an automatic soil water content control system for greenhouse, which consisted of drip irrigation nozzles, soil water content sensors, an on/off valve, a servo-motor assembly and a control program. The control logic adopted in the system was Ziegler-Nichols algorithm and rising time, time constant and over/undershoot ratio as control variables in the system was selected and determined by various control experiments to maintain small delay time and low overshoot. Based on the experimental results, it was concluded that the control system developed in the study could replace the unreliable conventional greenhouse soil water management.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1997년도 한국자동제어학술회의논문집; 한국전력공사 서울연수원; 17-18 Oct. 1997
• /
• pp.1684-1687
• /
• 1997

A dynamic load simulator which can reproduce on-ground the hinge moment of aircraft control surface is and essential rig for the loaded performance test of aircraft test of aircraft acutation system. The hinge moment varies wide in the aricraft flight enveloped depending on specific flight condition and maneuvering status. To replicate the wide spectrum of this hinge moment variation within some accuracy bounds, a force controller is designed based on the Quantiative Feedback Theory (AFT). Through the analysis on hinge moment dynamics, a design specification for the force controller is suggested. The efficacy of QFT force controller is verivied by simulation, in which combined aricraft dynamics/flight control law and hydraulic actuation system dynamics of aircraft control surface are considered.

• 대한기계학회논문집
• /
• 제19권4호
• /
• pp.1062-1070
• /
• 1995

The study deals with controlling the velocity of hydraulic motor with PI controller through the control of displacement pump which has higher efficiency than valve-controlled system. This was done as follows. First, we modified original displacement pump and designed this electrohydraulic puma system. Second, after experimenting static and dynamic characteristics, we identified system parameter of approximated model. Lastly, to control the velocity of hydraulic motor we controlled the angle of the swash plate of displacement pump. Test carried out in the laboratory shows that transient and steady state response could be improved by PI controller reducing power loss.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.985-990
• /
• 2007

This paper presents a novel control algorithm for position control of pneumatic cylinder. Generally, it is difficult to control the pneumatic servo system, due to nonlinearities such as air compressibility, the opening area of the valve, and frictional force between the cylinder and the piston. Especially, it is of significant importance for the control consisten-cy to return the cylinder pressures at equilibrium point to the initial states, still with guaranteeing the continuity of the pressures. For this purpose, the proposed control algorithm makes pressures of both cylinder chambers identical in magnitude but different in direction. The effectiveness and practicability of the control algorithm for the precise position control of the pneumatic cylinder are verified through the simulation study.

• 기계와재료
• /
• 제21권3호
• /
• pp.42-51
• /
• 2009

원자력/화력 발전소에서 사용중인 터빈출력제어장치(turbine power control device)는 유압 서보액추에이터(hydraulic servo actuator)로 구동하는 특수 스팀 밸브(steam valve)로서 터빈의 속도를 제어하고 스팀을 차단하는 기능이 있다. 대형 발전기(500~1000Mw)를 구동하여 양질의 전기를 생산하기 위해서는 발전기에 연결된 고압 및 저압터빈에 최적량의 스팀을 공급하여야 하고, 고속(화력 3600 rpm, 원자력 1800 rpm)으로 회전하는 터빈이나 스팀계통에 이상이 발생할 경우 터빈의 과속(over speed) 방지를 위하여, 즉시 터빈으로 공급되는 스팀을 차단하여 터빈을 보호해야 한다. 따라서 터빈의 속도제어와 계통의 스팀 량을 감시하여 차단하는 발전소의 특수 밸브의 신뢰성확보기술이 요구된다. 특히 원자력발전소의 경우 핵연료교환주기(약 24개월)에 밸브들을 정비 또는 교체하고 있어 이때마다 시스템과 매칭(튜닝)기술이 요구되었다. 본 연구에서는 전량 수입에 의존했던 원자력/화력 발전소의 특수 밸브인 터빈출력제어장치의 국산화 개발과 신뢰성확보기술 효과에 대하여 논하였다.