• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.3
• /
• pp.358-366
• /
• 2014

This paper proposes a quasi Z-source AC-AC converter with the low DC voltage distribution capability operating as a power electronic transformer. The proposed system has configuration that the input terminals of two quasi Z-source AC-AC converters are connected in parallel, also their output terminal are connected in series. Simple control method of duty ratio was proposed for the in phase buck-boost AC voltage mode and the DC output voltage control. DSP based experiment and PSIM simulation were performed. As a result, the PSIM simulation results were same with the measured results. By controlling the duty ratio under the condition of 100 [${\Omega}$] load, quasi Z-source AC-AC converter could buck and boost the AC output voltage in phase with the AC input voltage, and the same time, the constant DC voltage could be output without affecting the AC output characteristics. And, the DC output voltage 48[V] was constantly controlled in dynamic state in case while the load is suddenly changed ($50[\Omega]{\rightarrow}100[\Omega]$). From the above result, we could know that the quasi Z-source AC-AC converter can act as a power electronic transformer with a low DC voltage distribution capability.

• Archives of Plastic Surgery
• /
• v.33 no.6
• /
• pp.748-752
• /
• 2006

Purpose:Circular skin lesions between 10 and 35 mm in diameter generate problems often. Direct closure of the lesion risks excessive wound tension or wound dehiscence. Skin grafts heal slowly and often remain unsightly. Traditional skin flaps have a limited role. We treated this circular medium-sized skin lesion(10 - 35 mm sized) by reducing opposed multilobed(ROM) flap. Methods: ROM flap involves a series of semicircular lobes extending both cephalic and caudal from the defect. Direction of the semicircular multilobed flap is set parallel to relaxed skin tension line(RSTL) to minimize scar formation. First semicircle is drawn 60% in diameter of the defect. Second semicircles are drawn at the cephalic and caudal aspects of the original semicircles. These semicircles are 60% in diameter of the first semicircle. Additional semicircles are repeatedly drawn until the tension of skin flaps becomes free. ROM flap has a length-to-base ratio of 0.5 resulting in lower theoretical risk of end flap necrosis than a random pattern flap with a large ratio. The technique involves lobes most distant from the primary defect being transposed in turn closer to the defect. Results: The ROM flap reduces skin tension concerns, lowers the risk of flap necrosis and allows for quicker and more aesthetic healing. Results were generally good and major complications, such as dehiscence, infection, or delayed healing, did not occur. Conclusion: ROM flap repair allows the plastic surgeon an additional option when faced with a circular medium-sized skin lesion.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.4 no.4
• /
• pp.64-71
• /
• 2001

Treatment efficiency was examined of a pond-wetland system constructed for water quality conservation of Koheung Estuarine Lake over one year after its establishment in July 2000. The system is composed of primary and secondary ponds in series and six wetland cells in parallel. Cattails (Typha angustiflora) were planted in three wetland cells and common reeds (Phragmites australis) in three other cells. Water pumped from Sinyang Stream flowing into the Lake was funneled into primary pond whose effluent was discharged into secondary pond by gravity flow. Effluent from secondary pond was distributed into each wetland cell. SS, $BOD_5$, T-N, and T-P concentrations in influent to primary pond, and effluent from primary pond, secondary pond, and three wetland cells planted with cattails were analyzed for about one year from August 2000 to August 2001. The removal rates at primary pond for SS, $BOD_5$, T-N and T-P were 29%, 30%, 15%, and 36%, respectively. The abatement rates at secondary pond for SS, $BOD_5$, T-N and T-P were 38%, 40%, 30%, and 47%, respectively. The reduction rates measured at three cattail-planted wetland cells for SS, $BOD_5$, T-N and T-P were 54%, 57%, 60%, and 68%, respectively. Considering early stage of the pond-wetland system and inclusion of winter during the research period, its treatment efficiency was rather good. Cattails had not yet grown to dense stands due to initial establishment period, which resulted in slightly lower treatment efficiencies of wetland cells for these pollutants, compared with those of ponds.

• Economic and Environmental Geology
• /
• v.5 no.3
• /
• pp.133-144
• /
• 1972

The mine of our present concern is situated at Shim-ri, Gusan-myon, Changwon-gun, Kyongsang-namdo, with lattitude $128^{\circ}35^{\prime}{\sim}36^{\prime}N$ and longitude $35^{\circ}03^{\prime}{\sim}04^{\prime}E$. This mine has not been noticed until the intermittent geological survey for the ore deposits were initiated from September, 1967 till 1970. The main mineralized zones, No.1 and No.2 zones, were studied by the diamond drilling of 9 holes down to the total depth of 1,140m, and found to have ore reserves of Cu 1.99% ore, estimated to reach around $358,000{\frac{M}{T}}$ (proved $117,000{\frac{M}{T}}$, indicated $241,000{\frac{M}{T}}$), which triggered the new exploitation of this mine. Geological composition of the district near the mine is mainly from the andesite belonging to the Silla Series of Kyongsang System and the distribution is broadly spread. Ore deposits are the hydrothermal one, filling the shear zone formed alongside the andesite main joint. There are two stripes of copper bearing mineralized zone which are about 40~70 meters apart and parallel to each other, in addition to which two others are expected. The strike of the main mineralized zone lies at $N15^{\circ}{\sim}20^{\circ}W$, the dip at $60^{\circ}{\sim}70^{\circ}NE$. The principal components of the ore mineral are chalcopyrite, bornite and as secondary, cuprite, tenorite, azurite and malachite. Pyrite, magnetite, specular hematite, very little of galena, sphalerite, quartz, epidote, zoisite, chlorite and calcite are found as gangue mineral. Confirmed by the drilling, the main mineralized zone, No.1 zone, has the length of 320m, average width of 1.62m, Ag 26g/t, Cu 1.84% and the average width of the ore zone except the narrow barren andesite horse interposed in the mineralized zone is 1.32m with Ag 32g/t and Cu 2.26%. The mineralized zone No.2 is 340m long, 1.00m wide with Ag 30g/t and Cu 2.15%. Neglecting the barren andesite horse the width is 0.73m with Ag 42g/t and Cu 2.94%.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.1
• /
• pp.174-182
• /
• 2014

Recently, not only common types of hybrid electric vehicle (HEV) such as series or parallel but many other types of HEVs including 4WD hybrid electric vehicle have been developed and released. In this study, analysis of fuel economy and driving performance for 2WD and 4WD HEV are conducted using backward simulation based on dynamic programming. To analyze the characteristics of 4WD HEV, tire slip model based on vehicle dynamics was applied to the backward simulation program. As a result, 2WD HEV shows better fuel economy than 4WD HEV because of relatively simple configuration. However, in a severe road condition, 4WD HEV shows better driving performance that 2WD HEV had about 6% of impossible time to follow the driving cycle though the 4WD HEV had no impossible time.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.3
• /
• pp.35-43
• /
• 2007

In this paper, the inductive power collector using electromagnetic induction for vehicle such as the PRT(Personal Rapid Transit) system is suggested and son ideas for power collector design to improve tile power transfer performance are presented. And also, the analysis of the inductive power transfer system in conjunction with series resonant converter operating variable high frequency is shown. Of particular interest is the sensitivity of the complete system to variations in operational frequency and parameters. In inductive power transfer system electrical power is transferred from a primary winding in the form of a coil or tract to one or more isolated pick-up coils that my relative to the primary. The ability to transmit power without contact enables high reliability and easy maintenance that allows inductive power transfer system to be implemented in hostile environments. This technology has found application in many fields such as electric vehicles, PRT(Personal Rapid Transit) etc. But, low output power is generated due to a loosely coupled characteristic of the large air-gap. Therefore, we will show you various characteristic of inductive power transfer system as double layer construction of secondary winding, which was divided in half to increase both output current and output voltage, a model of power collector and parallel winding structure, a model of concentration/ decentralization winding and the effects of parameter and operational frequency variation.

• Steel and Composite Structures
• /
• v.36 no.2
• /
• pp.213-228
• /
• 2020

Shape Memory Alloys (SMAs) are new materials used in various fields of science and engineering, one of which is civil engineering. Owing to their distinguished capabilities such as super elasticity, energy dissipation, and tolerating cyclic deformations, these materials have been of interest to engineers. On the other hand, the connections of a steel structure are of paramount importance because of their vulnerabilities during an earthquake. Therefore, it is indispensable to find approaches to augment the efficiency and safety of the connection. This research investigates the behavior of steel connections with extended end plates equipped hybridly with 8 rows of high strength bolts as well as Nitinol superelastic SMA bolts. The connections are studied using component method in dual form. In this method, the components affecting the connections behavior, such as beam flange, beam web, column web, extended end plate, and bolts are considered as parallel and series springs according to the Euro-Code3. Then, the nonlinear force- displacement response of the connection is presented in the form of moment-rotation curve. The results obtained from this survey demonstrate that the connection has ductility, in addition to its high strength, due to high ductility of SMA bolts.

• Journal of KIISE:Software and Applications
• /
• v.27 no.4
• /
• pp.412-421
• /
• 2000

In spite that the main contents of mathematical and scientific learning are understanding principles and their applications, most of existing educational softwares are based on rote learning, thus resulting in limited educational effects. In the artificial intelligence research, some progress has been made in developing automatic tutors based on proving and simulation, by adapting the techniques of knowledge representation, search and inference to the design of tutors. However, these tutors still fall short of being practical and the turor, even a prototype model, for learning problem solving is yet to come out. The geometry problem-solving tutor proposed by this research involves dynamic inference performed in parallel with learning. As an ontology for composing the problem space within a real-time setting, we have employed the notions of propositions, hypotheses and operators. Then we investigated the mechanism of interactive learning of problem solving in which the main target of inference involves the generation and the test of these components. Major accomplishment from this research is a practical model of a problem tutor embedded with a series of inference techniques for algebraic manipulation, which is indispensable in geometry problem solving but overlooked by previous research. The proposed model is expected to be applicable to the design of problem tutors in other scientific areas such as physics and electric circuitry.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.2
• /
• pp.497-507
• /
• 2010

This paper presents current unbalance improved half-bridge LLC resonant converter using the two transformers with different leakage inductances. The proposed converter resonates with the leakage inductance and magnetizing inductance of the transformer and the resonant capacitance. The converter operates in a wide load range and satisfies the zero voltage switching even under the light load. The series-parallel connected two transformers act as the transformers or the resonant inductances according to the operational modes, and the separate output filter inductance in the transformer secondary is not needed using the leakage inductance. The current unbalance of the secondary diode rectifier is improved using the different leakage inductances of the two transformers and the asymmetrical pulse-width modulation (PWM). In this paper, the operational principle of the converter is explained by the modes, and the design example for the prototype is also shown. To validate the performance of the converter, the prototype is implemented as the designed circuit parameters and the good performance of the proposed converter is shown through the experimental results

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.3
• /
• pp.669-676
• /
• 2016

North Korea has various ballistic missiles from short range to long range such as inter continental ballistic missiles. Short range ballistic missiles such as SCUD series are threatening to Korea peninsula. Therefore Korea is constructing various missile defense systems to protect country. Parameters influencing the received power from the target to the radar are transmitting power, antenna gain, carrier frequency, RCS(Radar Cross Section) of target and distance from radar to target. Especially, RCS and distance from target are not radar performance defined parameters but external parameters. Therefore radar deployment position that large RCS can be observed and target to radar distance should be considered in parallel to improve target detection probability. In this paper, RCS pattern of SCUD-B ballistic missile is calculated, received power is analyzed based on radar deployment position during ballistic missile trajectory and methode for optimum radar deployment position to improve target detection probability is suggested.